38777043
construction of transit accommodation building for officers at manali refinery of cpcl , earth work in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means (hydraulic excavators)/manually for depth upto 3.0m,including cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, and stacking of excavated material within a lead of 100m, including providing temporary supports to existing facilities viz., service lineslikewater pipes, electric under ground cablesetc. all complete as per the specifications and directions of engineer in charge. , backfilling / filling available earth after execution of the work to the proper grade and level with selected approved available excavated soil from soil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm, watering, rolling and ramming by manual methods/mechanical compactors, dressing, trimming etc. in foundations, plinths, etc.all complete as per directions of engineer in charge. , filling under the floor with quarry dustin layers of thickness not exceeding 150 mm, watering, rolling and ramming by manual methods/mechanical compactors, dressing, trimming etc. in below floor level all complete as per directions of engineer in charge. , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the designated area outside the refinery premises up to a lead of 7km (vaikkadu village) including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , supplying and filling m sand of specified quality underfootings,pedestal etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layersnot exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying in position plain cement concrete (pcc) 1:4:8 with 40mm & down size graded aggregate for levelling course/fill under footings,pedestal etc., for all depthsincluding all tools and tackles, labour and material charges, curing, compacting,in any shape, level, thickness, position and finishing the surface smooth/rough etc., complete as directed by engineer in charge. , providing, mixing and laying in position rcc m35 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m.using 53 grade ordinary portland cement in sub structure for all depths upto ffl level including cost of admixtures if used, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.,(excluding the cost ofreinforcement and shuttering), etc. all complete as specified and directed by engineer in charge. , all substructure works , providing, mixing andlaying in position rccm30 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 330kg/cu.m. using 53 grade ordinary portland cement in super structure for all heightsabove ffl level including cost of admixtures,labour charges, tools and tackles,providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. (excluding the cost of reinforcement, shuttering), etc. all complete as specified,and directed by engineer in charge. , all super structure works , providing and fixing straight / inclinedcentering and shuttering in sub structure for all depths upto ffl levelincluding strutting, bracing, propping etc. keeping the same in position during concreting and de shuttering & removal of the same after specified period as per specifications.keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , providing and fixingstraight / inclined centering and shuttering in super structure at all heights above ffl level including strutting, bracing, propping etc. keeping the same in position during concreting, de shuttering & removal of the same after specified period as per specifications etc.,keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500 for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying brick masonry using cement mortar 1:5 (1 cement:5 coarse sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying half brick masonry in cement mortar 1 : 4 (1 cement : 4coarse sand) for all depths and heightsincluding cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing 15mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrick masonry/ concrete surfaces including preparation of base, cleaning, chipping, scaffolding, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles, material costs etc. as per specifications and asdirected by the engineer in charge. , providing 12mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrickmasonry, concrete surfacesincluding preparation of base, cleaning, chipping, scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 6mm thick cement plaster in cement mortar 1:3 (1cement:3 fine sand by volume) on roof ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges,material costs,tools and tackles etc.as per specifications and as directed by the engineer in charge. , providingandapplying two coats of interior emulsion with wall putty of approved make of any shades/coloursover one coat of primer asper the specifications includingnecessaryscaffolding and surface preparation consisting of application of plaster of paris punning over entire surface, filling all holes and depressions with white cement, applying a coat of primer, two or more coats of oil based putty(as per manufacturers recommendations)sand paperingetc. in walls and roof ceiling, complete as per specification and as directed by engineer in charge. , providing and applyingweather proof textured exterior paint on rcc /brick walls / plastered surface etc. of asian ,nerolac,berger or any other equivalent approved make, one coat of primer andtwo or more coats (to give a smooth and even shade)of anti fungal, water proof, anti flakingweather proof paintof approved quality and shade etc. asper the specifications includingnecessaryscaffolding, cleaning and surface preparation, preparation consisting of application of plaster of paris punning over entire surface,filling all holes and depressions with plaster of paris, applying a coat of primer, two or more coats of oil/water based putty(as per manufacturers recommendations) sand papering etc., all complete as per specification and as directed by engineer in charge. , providing and laying water proofing membrane to roof of atactic poly propylene (app) with non woven polyster reinforcement having thin poly ethylene foil of approved quality inculding cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturers specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. (the thickness of atactic poly propylene (app) membrane to be considered as 4.0mm) , providing and laying first quality pressed clay tilesof size 300 mm x 300 mm (as per approved pattern not less than 18 mm thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement: 4 msand) mixed with 2% integral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement: 4 m sand) and finishing neat including all tools, tackles, equipments, labour,materials,hacking of concrete,necessary surface preparation,pointing with cement mortar 1:4 mixed with 2% integral water proofing compound , etc.whereever required , complete as per specifications and as directed by engineer in charge. , providing and laying 60mm thick factory made cement concrete interlocking rubber mould paver block s of m20 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in two or more colour and pattern over 50mm thick m sand cushining well rambled and laid without undulation etc. as per drawing , all complete as per the direction of engineer in charge. , providing and fixing 18mm thick machine cut, mirror polished, premoulded and pre polished machine cut granite for platformsof approved qualityfor wash basin/ vanity counters,pantry,shelves,steps,150mm wide skirting with edge polishing etc.of required size of tan brown colour or any other colour/shade laid 20mm thick base cement mortar 1:4 (1 cement:4 m sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening as per requirement etc., rubbing, curing, moulding & full bull nose edge polishing etc. complete at all levels as directed by engineer in charge. , fixed glazing with teakwood framework of size 50mm x 115mm with 6mm thk glass and cnc cur wooden panels with 2nd class teakwood finished with varnish and melamine finish along with wooden fins of size 50mm x 100mm as shown in the drawing , providing and fixingelevation jaali using ss 304 frameworkwith sections of size 37.5mm x 62mm x1.5mm thickness ofheight and details as shown in drawing. it is to be fixed & screwed to concrete walls using ss angle cleat of size 50mmx50mmx1.5mm thickness. additional members of the same size as required to be provided to fix with the jaali with concreteas shown in drawing. the 18mm thick wpc (wood plastic composite) jalitype panels to be cut to design and shape in cnc (computer numeric control) machine of shape and design as given in drawings,to befixed to ss frame work all as shown indrawings, the wpc cnc cut jali ,wooden beadingto besurface prepared with initial first coat ofprimer(ici duco primer or approved equivalent ) after sand papering, one coat of surface enhancer primer( ps2 duco white or approved equivalent) after applying putty (iciducoputty or approved equivalent ), 2 coats of premium quality air dryingspray painting(iciduco or approved equivalent)with glossy finish in colour allcomplete asdirectedby engineer in charge. , providing & fixing of aluminium fins as per the section & dimensions in drawings & allcomplete asdirectedby engineer in charge. , flooring and tiles , providing and laying of premium quality floor tiles of size 800x800of kajaria/johnson/somanyor approved equivalent,approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles,4skirting all around as per drawing ,along with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge as per drawing. , providing and laying of premium quality glazed vitrified flooring tiles of size 900x1200 or bigger of kajaria or somany or approved equivalent, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles,4skirting all around as per drawing ,along with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge as per drawing. , providing and laying of premium quality antiskid vitrified / ceramic toilet tiles of size 600x600 ofkajaria or somany or approved equivalent make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles, with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge. , providingand laying coloured glazed vitrified / ceramic tiles of size 600 mm x 1200 mm for wall/dado(grade i quality), of kajaria or somany or approved equivalent & shade including tile fix adhesive, pvc beading with matching colour, pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface, all complete with material costs, tools and tackles, stagings labour charges as perspecifications and as directed by engineer in charge. , providingand laying coloured glazed vitrified / ceramic tiles of size as per drawing for elevation wall/dado(grade i quality), of kajaria or somany or approved equivalent & shade including tile fix adhesive, pvc beading with matching colour, pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface, all complete with material costs, tools and tackles, stagings labour charges as perspecifications and as directed by engineer in charge. , door, windows & ventilators , providing and fixing in position openable special & fixed glazing in staircase upvc windows two track(no. of panels to be decided jointly with eic) (with clear 5mm thick glass double glazing), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , providing and fixing in position fixed upvc framed glazingabove main door (with clear 5mm thick glass), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , providing and fixing in position openable upvc windows(with clear 5mm thick glass ), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , providing and fixing in position upvc sliding doors(with clear 5mm thick glass ), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , window grills made out of 12mm square ms rods4 spacing inserted into the wall at regular intervals including applying two coats of sythentic enamel paint over a coat of zinc chromate , providing and fixing in position upvc louvers ventilators (with pin headed 5mm thick glass ), white in colour including all fixtures, fastenings,300mm long friction stay hinges(himax or approved equivalent), handle with flush lock, epdm gaskets, wool pile, etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , providing and fixing bright finished brass 100mm mortice latch and lock of godrej or approved equivalent isi marked with four levers and a pair of polished stainless steel decorative handles(size of handles to match the door size) with necessary screws etc. complete (best make of approved quality) as specified by engineer in charge. , providing and fixing isi marked, overall 30mm thickblock board flush door shutters of greenply/century/archidply or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on both sides ost vineer of archidply or approved equivalent, providing and fixing 6mm thick second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) ] including providing wooden filler/sealer, stainless steel lock , teak wood lipping, door bush, finishing etc . all complete as directed by engineer in charge. , providing and fixing isi marked, overall 30mm thickblock board flush door shutters of greenply/century/archidply or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on one side ost vineerof archidply of approved equivalent and acp with 3mm thick on rear side on other side of archidply or approved equivalent, providing and fixing 6mm thick second class teakwood perimeter beading by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) ] including providing wooden filler/sealer, stainless steel lock , teak wood lipping, door bush, finishing etc . all complete as directed by engineer in charge. , providing and fixingsecond class teak wooden framesfor doors for all heights including all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/rcc by means of 300mm x 25mm x 6mm thick m.s. hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia m.s. dash fastner, painting with two coats of approved shade and make (ici or equivalent) synthetic enamel paint over appoved quality primer coat, finishing etc. all complete as dirercted by engineer in charge. , providing and fixing main door with second class teakwoodfor frames and for doorsincluding all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/rcc by means of 300mm x 25mm x 6mm thick m.s. hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia m.s. dash fastner. , railing , toughened glass hand rail with jindalss 304 gradebalustrades 38mm sq. tubes 2mm thick with ss base cups to cover theholes made in the flooringas mentioned in drgswith glazing clips at bottom and top to hold the toughened glass panels . the top railing isto be provided with 38mm dia jindalss 304 gradepipe 2mm thick . the balustrades needto be firmly fixed in to the concrete floor slab with proper grouting chemicals . , plumbing , providing & fixing geberit wall mounted water closet with concealed cistern (concealed cistern with full frame & chrome finish push plates all complete) of hindwareor approved equivalent or approved equivalent make including all fittings,slim line health faucet with hose & hook, other standard accessories, all fittings and fixturesincluding cutting walls, floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providingandfixingin position vasca over the counter wash basinof hindware or approved equivalent with one c.p brass single lever pillar cock with aerator tap of hindware or approved equivalent, one no ofcp angle valve with wall flange, c.p. brass waste, pvc drain pipewith heavy bottle trap of hindware or approved equivalent make,c.i. brackets and all accessories complete including cutting walls, floors and making good the same, painting all exposed metallic surfaceswith 2 coats of approved shade and quality synthetic enamel paint over an approved quality priming coat of red oxide zinc chromate making all connections, fixing, finishing, etc. all complete as per specifications and as directed by engineer in charge. , providingandfixingin position alto pedastal wash basinof hindware or approved equivalent with one c.p brass single lever pillar cock with aerator tap of hindware or approved equivalent, one no ofcp angle valve with wall flange, c.p. brass waste, pvc drain pipewith heavy bottle trap of hindware or approved equivalent make,c.i. brackets and all accessories complete including cutting walls, floors and making good the same, painting all exposed metallic surfaceswith 2 coats of approved shade and quality synthetic enamel paint over an approved quality priming coat of red oxide zinc chromate making all connections, fixing, finishing, etc. all complete as per specifications and as directed by engineer in charge. , providing and fixing in positionstainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheetsupported onm.s. brackets, supply, fixing ofm.s.brackets, fasteners, sinkcock (quarter turn range) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipewith heavy bottle trap of parry ware or approved equivalent make, inlet pipe, drain pipe , rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls where ever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing etc., all complete as directed by engineer in charge. , providing and fixingmirror of superior glass of size 400 mm x 500mmof parryware or approved equivalent complete with cp brass screws, fastners and washers complete as directed by engineer in charge. , providing and fixing600 mm long cp rodtowel rail of parry ware make or approved equivalent complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour all complete as specified by engineer in charge. , providing and fixing in position approved quality liquid soap dispenser ofeuronicsor approved equivalent make, of standard size with snap fittings, including drilling holes, fixing with cp screws all complete as directed by engineer in charge. , providing and fixing of cp brass twin robe hook of parryware/approved equivalent including fixing the coat hook including drilling holes on plastered/tiled wall and doors fixing the coat hook with cp screws including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , providing and fixing in position approved quality shower panel of jaquar or approved equivalent make, of standard size all complete as directed by engineer in charge. , providing and fixing15 mm nominal outer dia. & sdr11 chlorinated poly vinyl chloride (cpvc) pipes, of approved equivalent make having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings & accessories including fixing the pipe with clamps at 1m spacing. this includes jointing of pipes & fittings with one step cpvc solvent and testing of joints complete as per directions of engineer in charge. , same as sl. no: 58 above, but for 20mm nominal outer dia. pipes , providing and fixing 75mm dia. nominal boreunplasticised rigidpvc (upvc pipe) sch. 40 water line pipes on wall face conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 leaving 10mm gap for thermal expansion (single socketed pipes) with necessary fittings /accessories etc.all complete as per specifications and as directed by engineer in charge. , same as sl. no. 60 above, but for 110mm dia. nominal bore pipes. , providing and fixing 160 mm dia. rigid pvc rain water pipeswith ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg/ sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing 110mm dia.rigidpvc pipes with pressure rating of 4 kg/ sq.cm of approved brand including all fixtures as vent pipe for septic tank, machine welded, rubber ring jointsusing approved lubricant, making hole in the slaband restoring the same to the original condition including provision of cowl in the septic tank vent pipe etc. complete as per specifications and directions of engineer in charge. , providing and fixing bibcock single lever range with flange of parryware or equivalent approved 15mm nominal bore cp including fixingand connections, etc. completeas directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal borebrass angle valve including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing 25 mm nominal bore gun metal gate valve with cast iron (ci) wheel of approved quality (screwed end) including all fittings etc. complete as directed by engineer in charge. , same as sl. no. 66 above, but for 40mm nominal bore gate valve. , supplying and laying custom (prefabricated) pvc floor sumps/ floor traps fabricated out of 110mm dia. 6 kg/cm2 class pvc pipes with inlet and outlets from 40mm upto 75mm, including providing water seal, fixing to a perfect level, laying cement concrete in 1:3:6 mix cp/pvc colour grating with frame at 4mm below finished floor level making holes in masonry or concrete cutting surfaces conveying all dismantled portions and clearing the site,making leak proof joint and testing, etc. complete and as directed by engineer in charge. , special items , supplying and fixing of 12 mm thick unpolished sadhar ali grey granite slab (shade and colour as approved by eic) out of 300x 600mm available size of uniform shade from the same rock cut in to different shape and size as per drgs and all edges are chamfered of size 6mmx6mm so as to form a v groove when joined with adjacent granite to be fixed above the plastered surfacebrick wall /columns where ever necessary usingcement mortar plaster 1:3 and pasting with cement slurry of reqd consistency , supplying and fixing of hpl laminate in exterior front façade teak wood shade ( as approved by eic) of funder maxx , royal touche or green lam, 4mm thickfixed using using necessary sealants over and above 25x50x 2mm alu hollow rectangular section frame workwhich is screwed to the walls/ concrete surface . , supplying and fixing reynoarch exterior wood finish acp louvres in the exterior front façade as mentioned in drgs. it isfixed using using interlocking over and above 25x50x 2mm alu hollow rectangular section runners at 600 mm centres which is screwed to the walls/ concrete surface , providing and applying two coats of sheenlac or its eqvt varnish after sanding the surface well, covering the porous surface with sheenlac or its eqvt wood sealer and wood putty , final coat will be with mrf / asianor its eqvt melamine coatmatt finish as approved by eic., using machine spray gun , , providing necessary temporary barricading workswith 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3 m , embedding the same in firm ground etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works.the same will be the property of contractor. , electrical , supply & fixing of distribution boards , supply and erection of 8 way tp&n distribution board factory made with powder coated finish and with double door / dust & vermin proof wall mounting for distribution of of power loads comprising of following : 1 no : 63amps tpn mcb as incomer 24 nos : 16 25 a amps sp mcbs as outgoing feeders to provide power plugs and ac units , supply and erection of 10way spn distribution board factory made with powder coated finish and with double door/dust & vermin proof wall mounting forcommon & external usage comprising of following: 1 no : 20ampsdpmcb as incomer 8 nos : 6 amps sp mcbs as outgoing feeders , supply and fixing of ac mcb box of 10a capacity as per the directions of engineer in charge , supply & fixing of switch box: switch box shall beconcealed type galvanised metal boxes gi boxes with 120 gsm zinc coating manufactured from gi sheet having 250 hrs protection against red rust.good quality threads. earthing terminal to avoid shock. box to be supplied along with cover plate and base frame , a) 1 or 2 module , b) 3 module , c) 4 module , d) 6 module , e) 8 module , f) 12 module , g) 16 module , supply & fixing of pvc conduits: pvc conduit installation and laying of conduits in concealed or surface mounted for circuit/main/telephone/video conferencing/data wiring with clamps, saddles, pull boxes and all other conduit accessories as per the specifications of this tender and directions of engineer in charge. , a) installation of 32 mm pvc conduit , b) installation of 25 mm pvc conduit , c) installation of 20mm conduit , supply & fixing of pvc conduits: supply and laying of following sizes of empty conduits for use of cctv / wifi etc. , a) 25mm pvc conduits , b) 20mm pvc conduits , supply & fixing of heavy duty pvc conduits: supply laying of heavy duty pvc conduit of 25 mm size to run the 3c external lighting cable along the wall, or surface or to be burried under ground in to a depth of 450 mm with necessary fixing accessaries and filling materials etc. , tv, telephone, data networking system : , a) supply and fixing of data outlets with i/o , b) supply and fixing of voice outlets with i/o , c) supply and fixing of tv socket outlets , compound wall , earth work in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means (hydraulic excavators)/manually for depth upto 2.0m,including cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, and stacking of excavated material within a lead of 100m, including providing temporary supports to existing facilities viz., service lineslikewater pipes, electric under ground cablesetc. all complete as per the specifications and directions of engineer in charge. , backfilling after execution of the work to the proper grade and level with selected approved available excavated soil from soil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm, watering, rolling and ramming by manual methods/mechanical compactors, dressing, trimming etc. in foundations, plinths, etc.all complete as per directions of engineer in charge. , supplying and filling m sand of specified quality underfootings,pedestal etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layersnot exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying in position plain cement concrete (pcc) 1:4:8 with 40mm & down size graded aggregate for levelling course/fill under footings,pedestal etc., for all depthsincluding all tools and tackles, labour and material charges, curing, compacting,in any shape, level, thickness, position and finishing the surface smooth/rough etc., complete as directed by engineer in charge. , providing, mixing and laying in position rcc m35 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m.using 53 grade ordinary portland cement in sub structure for all depths upto ffl level including cost of admixtures if used, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.,(excluding the cost ofreinforcement and shuttering), etc. all complete as specified and directed by engineer in charge. , rcc column in footing , rcc plinth beam , providing, mixing andlaying in position rccm30 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 330kg/cu.m. using 53 grade ordinary portland cement in super structure for all heightsabove ffl level including cost of admixtures,labour charges, tools and tackles,providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. (excluding the cost of reinforcement, shuttering), etc. all complete as specified,and directed by engineer in charge. , a. column above plinth beam , providing and fixing straight / inclinedcentering and shuttering in sub structure for all depths upto ffl levelincluding strutting, bracing, propping etc. keeping the same in position during concreting and de shuttering & removal of the same after specified period as per specifications.keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , providing and fixingstraight / inclined centering and shuttering in super structure at all heights above ffl level including strutting, bracing, propping etc. keeping the same in position during concreting, de shuttering & removal of the same after specified period as per specifications etc.,keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , providing and laying brick masonry in super structureabove ffl level using cement mortar 1:5 (1 cement:5 coarse sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing 15mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrick masonry/ concrete surfaces including preparation of base, cleaning, chipping, scaffolding, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles, material costs etc. as per specifications and asdirected by the engineer in charge. , providing and applyingweather proof textured exterior paint on rcc /brick walls / plastered surface etc. of asian ,nerolac,berger or any other equivalent approved make, one coat of primer andtwo or more coats (to give a smooth and even shade)of anti fungal, water proof, anti flakingweather proof paintof approved quality and shade etc. asper the specifications includingnecessaryscaffolding, cleaning and surface preparation, preparation consisting of application of plaster of paris punning over entire surface,filling all holes and depressions with plaster of paris, applying a coat of primer, two or more coats of oil/water based putty(as per manufacturers recommendations) sand papering etc., all complete as per specification and as directed by engineer in charge. , providing and fixingdouble shutter stainless steel gate of size 4.2 m x 1.98 mas shown in drgs fixed to rcc columnswith necessary hinges, and all necessary accessorieswithcast iron solid cup to swivel and roate the end post of gate . , fixing of granite slab as per the shade approved byt the engineering charge 18mm thick in cement mortar with necessaryclamp & brackets in the entrance compoundwall adjacent to the gate as shown in the drawing (logo & letters should be fix above the granite slab) , granite fins of size (200x35mm) to the required height as shown in the drawing to be fix to brick & r.c.c lintel in the entrance compound wall. , ms steel grills in compound wall including applying finish paint as per drawing & directions of engineer in charge , rear courtyard , supplying and fixing of 12 mm thick unpolished sadhar ali grey granite slab (shade and colour as approved by eic) out of 300x 600mm available size of uniform shade from the same rock cut in to different shape and size as per drgs and all edges are chamfered of size 6mmx6mm so as to form a v groove when joined with adjacent granite to be fixed above the plastered surfacebrick wall /columns where ever necessary usingcement mortar plaster 1:3 and pasting with cement slurry of reqd consistency . , providing and fixingaluminium rafter at rear court yard with wooden finish of size 50 x100mm x2mm as shown indrgs fixed to the brick compoundwall on one side and to the sunshade fascia brick work on other side and grouted properly using rcc 1:1.5: 3. , providing and laying brick masonry in super structureabove ffl level using cement mortar 1:5 (1 cement:5 coarse sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing 15mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrick masonry/ concrete surfaces including preparation of base, cleaning, chipping, scaffolding, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles, material costs etc. as per specifications and asdirected by the engineer in charge. , providing and applyingweather proofexterior paint on rcc /brick walls / plastered surface etc. of asian ,nerolac,berger or any other equivalent approved make, one coat of primer andtwo or more coats (to give a smooth and even shade)of anti fungal, water proof, anti flakingweather proof paintof approved quality and shade etc. asper the specifications includingnecessaryscaffolding, cleaning and surface preparation, preparation consisting of application of plaster of paris punning over entire surface,filling all holes and depressions with plaster of paris, applying a coat of primer, two or more coats of oil/water based putty(as per manufacturers recommendations) sand papering etc., all complete as per specification and as directed by engineer in charge. , interior contractor to mandatorily enagage an external residential building / apartmentinterior contractor for this work. the proposed interior contractor to be placed for approval to eic prior to start of the work. necessary documentary evidence for past experience to be submitted to eic for approval. , supply andfixingtv cabinet in living roomas given inthe drawings using 19mmthk bwpplywood forcabinetand 12mmthkbwpplywoodforwallpanellingusingecohingesoritsequivalent.theinnersurfaceofthecabinetis laminatedwith0.7mmthkandoutsidesurfacefinishedwithglossy laminatefinishedwithmelaminepolishasperthe drawing as approved by engineer in charge. , wall panel area (glossy laminate finish) , console unit & shelf area (matt laminate finish) , wall paper in living room and office room as given in drawing , wall panelling with 12mm thk bwp plywood partly with ost & melamine finsh and partly with designer charcol board as suggested by enginer in charge. , laquered full height sliding door : wardrobe cabinet as given in the drawings with box type cabinets using 19mm thk bwp plywood and laminated with 0.7mm thk. the sliding shutter shall be made out of aluminiumframeworkof50mmx25mmplywood@600mmintervalsandbothsidestheframeworkwillbtcovered with6mmbwpplywood.theinsideoftheshutterwillbefinishedwith0.7mmlaminateandtheoutersidewillbe finished with acrylic finish laminate and coloured glass/ mirror as per the drawing as approved by engineer in charge. all cabinets edges will be finished with rehal tap matching to the exterior finish. , wardrobecabinetalongwithdressingtableasgiveninthedrawingswithboxtypecabinetsusing19mmthkbwp plywood and laminated with 0.7mm thk, shutter will be with 2 track sliding with hettich or its equivalent. the sliding shutter shall be made out of aluminium framework of 50mm x 25mm plywood @ 600mm intervals and both sides the framework will bt covered with 6mm bwp plywood. the inside of the shutter will be finished with 0.7mm laminate and the outer side will be finished with matt finish laminate and coloured glass/ mirror as per the drawing as approved by engineer in charge. all cabinets edges will be finished with rehal tap matching to the exterior finish. , kitchen bottom cabinet shall be as per drawing, the cabinets shall be of bwp plywood with 0,7mm thk laminate inside and1mmthk laminateoutside of glossy & matt combinationwithrehaltap,ecohinges, etc. the kitchencabinets shallhave necessary ss drawers, racks, shelves as suggested by enginer in charge. ss drawers to contain following accessories : stainless steel basket por cutlery, plain basket, plate basket oilpull out 4 nos tandam drawer , kitchenoverheadcabinetshallbeasperdrawing,thecabinetsshallbeofbwpplywoodwith0,7mmthklaminate insideand1mmthklaminateoutside of acrylic & matt combinationwithrehaltap,ecohinges,etc.thekitchencabinetsshallhavenecessaryss drawers, racks, shelves as suggested by enginer in charge. , crockery cabinet shall be as given in the drawing made out with box type cabinets using 19mm thk bwp plywood and laminated with 0.7mm thk, with openable shutter. the inside of the shutter will be finished with 0.7mm laminate and theoutersidewillbefinishedwithvineerand mirrorasperthedrawingasapprovedbyengineer in charge.all cabinets edges will be finished with rehal tap matching to the exterior finish. , providingwallpanellingon kitchenentrancearch etcwith25mmx50mmof1.5mmthickwith 0.583kg/m, aluminumhollowsectionsatnotmorethan 575mmc/c oneitherdirectionwithnecessaryclamps and fixing of 12 mm thick bwp plywood by screwing to the aluminium framework and providing 1.25 mm thick decorative lamination on exposed side by pasting to the plywood with all complete including material costs,labour costs,tools and tackles etc. all complete as directed by engineer in charge.the shade,colour,tecture of laminate shall beas approved complete all as per trade practice and as directed byarchitect/ consultant /engineer in charge. , providing and fixing suspended12.5mm gypboard plain panel ceiling as per drawing including gypserra perimeter channelis fixed along the perimeter of existing wall/ partition with the help of hilti hps 1 (6x40) impact anchor, at 600mm centres.gypserra ceiling angleis suspended by fixing it to the gyproc soffit cleat and or gyproc rawl plug 8x45mm creating 1220mm x 1220mm grid.gypserra intermediate channelis fixed to the gypserra ceiiing angle with m6 x 12mm hex bolt & hex nut arrangement or with 2 nos of ø4.2x13 gyproc metal to metal screw. the gypserra ceiling sectionis then fixed to the gypserra intermediate channelwith the help of gyproc connecting clipand in direction perpendicular to the intermediate channel at 457mm c/c. single layer of 12.5mm tapered edge gypboard plain tile (conforming to is 2095 part 1 : 2011) is then screw fixed to ceiling section with 25mm drywall screwsat230mm centres on ceiling section and 150mm at periphery of ceiling.finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with jointing compound & joint paper tape.the work is to be executed all complete at all different elevations including material costs,labour,tools and tackles as directed by engineer in charge. , down light 6watt gm brand or equivalent for false ceiling , cove light philips brand or equivalent for false ceiling , landscaping , trees , supplying and planting royal palm 10 to 12 tall including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting fox tail palm 6 to 7 tall including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting arica palm 4 to 5 tall including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting peltophorum above 8 tall including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting spathodia above 8 tall including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying terminalia mentalia 5 to 6 tall including cost of the plants and transportcharges etc., all complete. , shrubs , supplying and planting teccomo above 5 tall including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting ixora dwarf (12)1 to 2 tall bushy including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting golden duranda(6) bushy including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting pentanus grass bushy including cost of the plants, transport and plantinglabour charges etc., all complete. , supplying and planting spider lilly bushy including cost of the plants, transport and plantinglabour charges etc., all complete. , red earth with cow dung manure mixture and coco pith , manure filling, leveling, planting labours and material arrangement charges. , supply and installation of cylindrical triple layer white virgin plastic storage tank of capacity 1000 litres of sintex or approved equivalent onground floor roof with lid and making necessary cutout /holes for inlet, outlet and overflow pipes, necessary connections and sealing all joints properly,all complete. including, fixing, transportation to work site all complete as per drawings and directions of engineer in charge....
Due Date : August 21, 2023
Tender Value : ₹ Ref. Documents
