Ministry Of Commerce And Industry - Tamil Nadu

33596740 supply of sanitary pipes and fittings supply of sanitary pipes and fittings , approved make: parryware, hindware, jaquar, cera or equivalent , supplyingwater closet squatting pan ( indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) conforming to is : 7231, with all fittings and fixtures complete. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests , supplyingwhite vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete. w.c. pan with isi marked white solid plastic seat and lid , .supplyingwash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and makinggood the walls wherever required: white vitreous china wash basin size 550x400 mm with a pair of 15 mm c.p. brass pillar taps , supplying stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets : kitchen sink without drain board , 610x460 mm bowl depth 200 mm , supplyingwhite vitreous china flat back half stall urinal of size 580x380x350 mm with necessary c.p. brass couplings and clamps complete, including painting of fittings: , supplying , p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. flexible pipe, 32 mm dia , supplying600x450 mm beveled edge mirror of superior glass ( of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , supplyingtoilet paper holder : c.p. brass , supplying of type b swr pvc soil and waste fittings, 6 kg / cm2. as peris 14735 for fittings, , 100 mm dia. , 75 mm dia , supplying of type b swr pvc soil and waste fittings, 6 kg / cm2. as peris 14735 for fittings, , 110 mm dia. elbow , 110 mm dia. tee , 110 mm dia. endcup , 110 mm dia.shoe , 110 mm dia. y , 75 mm dia. tee , 75 mm dia. endcup , 75 mm dia. y , 75 mm dia. shoe , `supplying and fixing of type b swr pvc floor trap .100 mm inlet and 75 mm outlet , supplyingptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement . 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms , supplying ptmt shelf 440 mm long, 124 mm width and 36 mm height , weighing not less than 300 gms. , supplyingc.p. brass health faucetfor ewc . 15mm nominal bore , supplyingcp brass two way bib cock , supplyingc.p. brass wall mixerconforming to is:8931 15mm nominal bore , supplyingoval shapecounter wash basinof premium make , withnecessary fixing arrangement with 15 mm long bodypillar cocki / c32 mm c.p brass waste coupling of standard pattern , white wash basin of size 560x400 mm all complete , supplyingstainless steel grating , rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating , supplying1500x450 mm beveled edge 6 mm thick mirror superior glassfixed to 12 mm thick bwp ply wood board using 4 no. of ss studs & silica sealant including cost of necessary ss screws etc., complete , supplyingc.p.brass push cock of size 15 mm complete. , supplyinggun metal gate valve with c.i. wheel ( screwed end ) : , 25 mm nominal bore , 32 mm nominal bore , 40 mm nominal bore , 50 mm nominal bore , supplyingc.p. brass shower rose with 15 or 20 mm inlet :100 mm diameter , supplyingc.p. brass bib cock conforming to is:8931 : 15 mm nominal bore , supplying c.p. brass long body bib cock of a conforming to is standards and weighing not less than 690 gms. 15mm nominal bore , supplying c.p. brass stop cockof standard design and of approved make conforming to is:8931. 15mm nominal bore , supplying c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 :15mm nominal bore , supplyinggrating and colour. circular type 125 mm nominal dia with 25 mm waste hole. , supplyingsquare mouth s.w. gully trap class sp 1 complete with c.i. grating .100x100 mm size p type , supplyingnon pressure np2 class ( light duty ) r.c.c. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete : 150 mm dia rcc pipe , supplyingc.i. cover with frame for manholes / terrace tank , 455x610 mm rectangular c.i. cover ( light duty ) the weight of the cover including frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15 kg ) ...

Indian Rare Earths Limited - Tamil Nadu

32888076 1 dismantling and removal of r.r. masonry sl.no.1 of scope of work dismantling and removal of r.r. masonry / brick masonry / plain cement concrete work, etc. upto 5m height and dumping the debris within a lead of 500m etc. complete as per the direction of engineer in charge. 2 2 dismantling and removal of rcc foundation sl.no.2 of scope of wok dismantling and removal of rcc foundation / column / slab / beam, etc. in all heights upto 8m from floor level including all necessary scaffolding and dumping the debris within a lead of 500m etc., complete as per the direction of engineer in charge. 3 3 earthwork excavation sl.no.3 of scope of work earthwork excavation for foundation in all types of loose / hard soil and depositing the spoils with an initial lead of 200m and lift upto 2m including refilling etc., complete as per the direction of the engineer in charge. 4 4 supplying, providing and laying pcc 1:4:8 sl.no 4 of scope of work supplying, providing and laying pcc 1:4:8 mix for foundation / flooring work using 40mm and below grade hard blue granite jelly including all form works, mixing, laying, compaction, consolidation and curing, etc. complete as per standard specifications and as directed by the engineer in charge. 5 5 supplying, providing and laying pcc 1:2:4 sl.no.5 of scope of work supplying, providing and laying pcc 1:2:4 mix for foundation / flooring work / kerb wall drainage wall using 20mm and below grade hard blue granite jelly including all form works, mixing, laying consolidation and curing, etc. complete as per standard specifications and as directed by the engineer in charge. 6 6 supplying, providing & laying rr masonry sl.no..6 of scope of work. supplying, providing & laying rr masonry foundation / wall / retaining wall in cement mortar 1:6 for construction of wall using hard blue granite stone, etc. complete from 1m below ground level to 3m height above ground level with neat finishing including proper pointing & necessary scaffolding work etc complete as per standard specifications and as directed by the engineer in charge. 7 7 supplying, providing and laying dry rubble masonry sl.no.7 of scope of work supplying, providing and laying dry rubble masonry for soak pit for construction of wall using hard blue granite stone, etc. complete as per standard specifications and as directed by the engineer in charge. 8 8 supplying, providing and laying brick masonrysl.no.8 of scope of work supplying, providing and laying brick masonry in cm 1:6 using well burnt country brick of minimum size 22.9x11.2x7cm for foundation / kerb wall / wall upto 4.5m height from ground level including all scaffolding, staging, curing, etc. complete complying with standard specifications and as directed by the engineer in charge. 9 9 supplying, providing and fixing twisted reinforcement is 1786 hysd sl.no 9 of scope of work supplying, providing and fixing twisted reinforcement is 1786 hysd bars fe500d / fe550d ( tmt bars tata / agni / jsw ) including fabrication, cutting, bending, cold tying, with overlapping to the standard length wherever necessary and placing the reinforcement in position as per the direction engineer in charge including binding, provision of spacer bars, cover blocks and all other incidental charges, etc. complete for all rcc works as per standard specification and as per the direction of engineer in charge. 10 10 supplying, providing and laying cement concrete 1:1.5:3 for rcc works sl.no 10 of scope of work supplying, providing and laying cement concrete 1:1.5:3 for rcc works using 20mm and below grade hard blue granite jelly with specified reinforcement and all mixing, laying, compaction, leveling, consolidation and curing, etc., including the cost of centering / shuttering work, complete as directed by engineer in charge. 11 11 supplying, plastering with cm 1:4 mix 15mm thick sl.no 11 of scope of work supplying, plastering with cm 1:4 mix 15mm thick one coat floated hard & trowelled smooth etc for floors & walls upto 8m height with neat finishing and necessary grouting, etc. complete complying with standard specifications and as directed by the engineer in charge. 12 12 supplying, plastering with cm 1:3 mix 12mm thick sl.no 12 of scope of work supplying, plastering with cm 1:3 mix 12mm thick one coat floated hard & trowelled smooth for rcc beam, column, ceiling upto 8m height with neat finishing and necessary grouting, etc. including all scaffolding, etc. complete complying with standard specifications and as directed by the engineer in charge. 13 13 supply of paints and painting two coat with emulsion paint sl.no.13 scope of work supply of paints and painting two coat with emulsion paint ( asian / berger / nippon ) 1st quality of approved shade over a coat of cement primer for the external / internal masonry surface upto 10m height from ground level, including thorough scrapping, cleaning, removal of dirt, all tools & tackles, sandpaper and scaffolding arrangements, etc. and applying putty touch up works wherever required, etc complete as per specification and as per the direction of engineer in charge. 14 14 supplying, providing and laying with 10mm thick vitrified tiles sl.no.14 of scope of work supplying, providing and laying with 10mm thick vitrified / marbonite double charge tiles of size 600mmx 600mm johnson / kajaria / somania brand with cement mortar 1:2 and pointing including finishing the joint and pointing flush with the surface, etc. complete as directed by engineer in charge. 15 15 providing and fixing 18 20mm thick jet black sl.no.15 of scope of work providing and fixing 18 20mm thick jet black / coffee brown / tan brown granite slab for wash basin / kitchen / store room area including grinding & finishing the ends with half round and closing the joints with matching colour cement and polishing the slab to smooth finish, etc, complete as directed by the engineer in charge. 16 16 supplying, providing and fixing of 2 leaf ms gate sl.no.16 of scope of work supplying, providing and fixing of 2 leaf ms gate of required size consisting of ms angle i.s.a. 40x40x 6mm allround and for middle, horizontals and cross diagonals and covered with aluminium chequered plat 2mm thick ( jindal / hindalco ) with bolted / riveted joints and hinges arrangement including providing ms kondy and locking arrangements and painting the gate with two ( 2 ) coats of enamel paint ( berger / asian / nippon ) over a coat of zinc chromate primer ( berger / asian / nippon ) etc. complete as per specification and as per the direction of the engineer in charge 17 17 supplying, providing and fixing of gi c class heavy hollow tube hand rail sl.no.17 of scope of work supplying, providing and fixing of gi c class ( heavy ) hollow tube hand rail of approved size of steel ladder railing, balcony railing, staircase railing and similar works, including painting with two ( 2 ) coats of enamel paint ( berger / asian / nippon ) over a coat of zinc chromate primer ( berger / asian / nippon ) and cutting, welding, grinding, conveyance, electrical charges, etc. complete as per the specification and as per the direction of engineer in charge. 18 18 supplying, providing and fixing m.s. grills sl.no.18 of scope of work supplying, providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars including painting with two ( 2 ) coats of enamel paint ( berger / asian / nippon ) over a coat of zinc chromate primer ( berger / asian / nippon ) and cutting, grinding, conveyance, welding charges, electrical charges, etc. complete as per the specification and as per the direction of engineer in charge. 19 19 supplying, providing and laying 20 / 25mm sl.no 19 of scope of work supplying, providing and laying 20 / 25mm cpvc astrol / ashirvad pipes 20 20 supplying, providing and laying 20 / 25 / 32mm id pvc pipe sl.no 20 of scope of work supplying, providing and laying 20 / 25 / 32mm id pvc finolex / ashirvad / astral superthick pipes including all specials such as bend, elbow, reducer, tee, solvent cement, etc. complete as per the direction of engineer in charge. 21 21 supplying, providing & laying 40 / 50 / 63mm id pvc pipe sl.no.21 of scope of work supplying, providing and laying 40 / 50 / 63mm dia id pvc finolex / ashirwad / astral superthick pipes including all specials such as bend, elbow, reducer, tee, solvent cement etc. complete as per the direction of engineer in charge. 22 22 supplying, providing and laying 110mm dia id pvc pipe sl.no 22 of scope of work supplying, providing and laying 110mm dia id pvc finolex / ashirwad / astral ( 6kg ) pipes including all specials such as bend, elbow, reducer, tee, solvent cement, etc. complete as per the direction of engineer in charge. 23 23 supplying, providing and fixing bib tap / piller tap sl.no 23 of scope of work supplying, providing and fixing the cp sanitary fittings: bib tap / pillar tap as per the direction of engineer in charge. 24 24 supplying, providing and fixing parryware wall hung basin sl.no 24 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware duke wall hung basin, colour: white wash basins with necessary accessories ( waste coupling, waste hose, etc. ) as per the direction of engineer in charge. 25 25 supplying, providing and fixing the cp & sanitary fittings brass ball wall sl.no.25 of scope of work supplying, providing and fixing the cp & sanitary fittings: 20 / 25mm brass ball valve of heavy type including fixing, etc. as per the direction of engineer in charge. 26 26 supplying, providing and fixing 500 ltrs. water tank sl.no 26 of scope of work supplying, providing and fixing 500 ltrs. capacity sintex water tank with all inlet and outlet pipe fitting arrangements and 20mm brass float valves, etc., complete as per the direction of the engineer in charge. 27 27 supplying, providing and fixing the cp & sanitary fittings angle cock sl.no.27 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware angle cock as per the direction of engineer in charge. 28 28 supplying, providing, laying & fixing electrification concealed point sl.no.28 of scope of work supplying, providing, laying and fixing electrification concealed ( polythene pipe ) point with required wire ( make: finolex / havells / polycab ) , switch box, switches ( make: polycab / havells ) with all required necessary fittings including chipping, routing, clamping and all other incidental charges, etc. complete as per the specification and as per the direction of engineer in charge. 29 29 supplying, providing and fixing of exhaust fan 375mm sl.no.29 of scope of work supplying, providing and fixing of exhaust fan 375mm ( 15 ) sweep ( heavy duty ) with all required necessary fittings etc. complete as per the specification and as per the direction of engineer in charge. 30 30 fitter for miscellaneous works sl.no.30 of scope of work fitter for miscellaneous works such as dismantling the exiting steel structural / roof sheet etc. as directed by the engineer in charge. ( required materials will be issued by company on free of cost ) 31 31 engagement of labour sl.no.31 of scope of work engagement of labour ( mazdoor ) for miscellaneous work directed by the engineer in charge. ( required materials will be issued by company on free of cost ) ....

Chennai Petroleum Corporation Limited - Tamil Nadu

32849887 rate contract for projects related civil works at manali refinery of cpcl rate contract for projects related civil works at manali refinery of cpcl , cutting & clearing the areaof grass,rank,vegetation,wild growth bushes,trees and plants upto 30cm girth measured at a height 1.0m above ground leveletc, including removal of rubbish, grass, plants, bushes, by cutting it, removing completely as per directions of engineer in charge and collecting all cut grass, vegetation etc and disposing it atdesignated place upto 7 km lead outside the refinery premises(vaikkadu village) with all tools, labour etc. complete as per specfications and directions of engineer in charge. , cutting trees of girth above 30 cm upto & including 60cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal of unserviceable material atdesignated place upto 7 km lead outside the refinery premises(vaikkadu village )as per specifications and as directed by the engineer in charge. , cutting trees of girth above 60 cm upto & including 120cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal of unserviceable material atdesignated place upto 7 km lead outside the refinery premises(vaikkadu village )as per specifications and as directed by the engineer in charge. , cutting treesofgirth above 120cm upto & including 240cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal ofmaterial atdesignated place upto 7 km lead outside the refinery premises in vaikkadu area as per specifications and as directed by the engineer in charge. , cutting treesofgirth above 240cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal ofmaterial atdesignated place upto 7 km lead outside the refinery premises in vaikkadu area as per specifications and as directed by the engineer in charge. , earthwork in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means(hydraulic excavators) / manually for depth upto 1.5m,including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated/sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes,sewage pipes, electricunderground cables, etc.all complete as per the specifications and directions of engineer in charge. , sameassl. no. 60 abovebutfor depths beyond 1.5m upto 3.0m. , excavating trial pits manually of required size & depth upto 3m at locations as specified with necessary shoring, dewatering & backfillingas required, etc. complete as per specifications and as directed by engineer in charge. , backfilling after execution of the work toproper grade and level with selected materials from available excavated soil fromsoil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm,watering, rolling and ramming by manual methods/mechanical compactors , dressing, trimming etc. in foundations, plinths,pits etc.all complete as per directions of engineer in charge. , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the designated area outside the refinery premises up to a lead of 7km (vaikkadu village) including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) todesignated areas within the refinery premises including etp/ttp areasup to a lead of 3kmincluding re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , supplying and filling approved quarry dust of specified quality under floors, plinths,etc. for all depthsincluding the cost of quarry dust, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , collection of scrap (metal/steel scrap) from anywhere within the refinery premises including supply of necessary vehicles with driver,required labour,loading and unloading etc.and handing over the materials to scrap yard within the refinery premises with all tools and tackles,manpower etc.all compelte as directed by engineer in charge. , supplying and filling approved m sand of specified quality under floors, plinths, foundations etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying plain cement concrete (pcc)1:4:8 by volume(1cement : 4 m sand:8 coarse aggregate) with opc 53 grade and 40mm & down size graded crushed stone aggregates for all depths wherever required like in foundations, fillings ,floors,pavements & ramps or any other works etc., including shuttering, tamping, ramming, vibrating, curing, etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete including cement cost etc, all complete as directed by engineer in charge. , same as sl.no: 150 above,but for plain cement concrete (pcc)1:1.5:3 , providing and laying of reinforced cement concrete (rcc) 1:1.5:3 by volume (1cement: 1.5 m sand:3 aggregate) with opc 53 grade and 20mm and down size graded crushed stone aggregate materials for sub structure upto plinth beam levelfor all depths including pavement, machine mixing, curing, consolidating with vibrator, cement cost etcall complete as per instructions of engineer in charge excluding cost of shuttering and reinforcement. , same as sl.no: 170 above,but for super structure at all heights above plinth beam level. , providing,fixing formwork including centering, shuttering ,strutting and propping in sub structure at all depths wherever required including removal of the shuttering after the specified period is over and as directed by the engineer in charge complete with all materials, labour, consumables etc.(form work shall be supplied by the contractor and shall remain the property of the contractor) , providing, fixing formworkincluding centering, shuttering ,strutting and propping insuper structure at all heightswherever required including removal of the shuttering after the specified period is over and as directed by the engineer in charge complete with all materials, labour, consumables etc.(form work shall be supplied by the contractor and shall remain the property of the contractor) , providing, hoisting and fixing in position rcc precast elementswithreinforced cement concrete grade 1:1.5:3 (1 cement:1.5 m sand: 3 graded stone aggregate withwith opc 53 grade and 20mm & down size graded crushed stone aggregates)for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks,levelling, aligning and fixing/laying in position using crane, breaking brickwork and /or concrete surfaces and making good the same etc. all complete (excluding cost of reinforcement) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement(conforming to is 1786, grade fe500) for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, welding spacers, lifting hooks etc for all heights & depths etc. removing of scraps from site, all complete as directed by engineer in charge. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases etc.using non shrink grout of approved make equivalent including supply of material,roughening surface, cleaning with compressed air/water jets, ramming, curing,labour charges etc.all complete as directed by engineer in charge. , providing & fixing in position bitumen impregnatedboard 12 mm thk. of approved make premoulded bituminous expansion joint filler boards conforming to is:1838 p1/1983 in joints including application of primer as directed by engineer in charge. , providing & filling in joints bitumastic sealing compound 12 to 17mm width x 20 to 25 mm depthofapprovedmake conforming to is:1834 latest revision grade a including one coat of primer as per manufacturer’s specifications, drawings & as directed by engineer in charge. , providing and laying coping block with cement concrete 1:2:4with 12.5mm & down size graded crushed stone chip aggregates on top of masonry wall including providing pockets, openings, recesses, chamfering wherever required, tamping, curing and rendering if required to give a smooth and even surface etc. for all heights in any shape, profile, position and thickness etc. all complete as directed by engineer in charge. , providing and laying brick masonry in sub structure with bricks ofclass 5.0 in cement mortar 1:5 (1 cement:5 m sand)for all depths including the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, finishing the joints flush below ground level , curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in using cement mortar 1:5 (1 cement:5 m sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam/slab, embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying half brick masonry in cement mortar 1 : 4 (1 cement : 4m sand) for all depths and heightsincluding cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing random rubble masonry with hard stone in sub structure with cement mortar 1:6 (1cement:6 m sand) for toe wall , including the cement cost , tools & tackles, labour required to complete the job, rendering the full face with 1:3 cm as per the specifications and directions of engineer in charge. , same as item no:300 above ,but for superstructure. , providing&laying dry rubble soling (hard core) with 20 to 40 mm size metal, under foundations/ ground floor slab (grade slab) etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors etc., complete as per drawings, specifications and as per thedirections of engineer in charge. , providing 15mm thick cement plasterin cement mortar 1:4(1 cement:4 m sand by volume) onbrickmasonry, pcc/rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster,bands ,mouldings etc. as specifiedfor all depths and heights including labour charges,tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 12mm thick cement plasterin cement mortar 1:4 (1cement:4 m sand by volume) onbrickmasonry,pcc/rcc surfacesincluding preparation of base, cleaning, chipping ,packing of electrical,plumbing works ,scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster,bands ,mouldings etc. as specifiedfor all heights including labour charges,tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 6mm thick cement plaster in cement mortar 1:3 (1cement:3 fine sand by volume) on roof ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges,material costs,tools and tackles etc.as per specifications and as directed by the engineer in charge. , providingandapplying two coats ofinterior paint of interior emulsion paint with wall putty of birla white/jk white or any other approved equivalent make of any shades/coloursover one coat of emulsion primer asper the specifications includingnecessaryscaffolding and surface preparation, filling all holes, cracks and depressions with wall putty,sand paperingetc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of exterior emulsion paint of asian or any other equivalent approved brand of required shade and includingsurface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty of birla white/jk white or any other approved equivalent make, necessary scaffolding etc, etc all complete as per specifications and directions of engineer in charge. , providing and applying 3 coats of white wash of approved make and shade for all depths and heights including cleaning, preparation of surfaces, curing etc with all labours, tools, tackles, scafolding etc. complete as directed by engineer in charge and as per specifications. , providing and applying two coats of water proof decorative cement paint of approved make and approved shade, cleaning, including preparation of surfaces, priming coat with cement primer,curing etc. all complete as per directions of engineer in charge. , providing recessed pointing onrandom rubble masonrywall for all heights with cement mortar 1:3(1cement:3 m sand) including scaffolding/staging, finishing, curing, etc.allcomplete as specified and directed by engineer in charge. , providing and fixing 18mm thick machine cut, mirror polished, premoulded and pre polishedgranite for platformsof approved qualityfor shelves of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 (1 cement:4 msand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish,curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. , providing and fixing 20mm thick machine cut,polished cudappah slab of approved qualityfor kitchen sinks of required size of approved shade, colour, and texture jointed with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, for fixing as kitchen sink, rubbing, curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. , providing and laying vitrified floor tiles of 600mmx 600mmof stain guard1st class quality ofapproved makelaid on 20mm thick cement mortar 1:4 (1 cement:4 m sand) , including a coating of adhesive as per manufacturers specifications, flush pointing of joints of tiles with cement paste, grouting with white cement and pigment with colour matching the shades of tiles including skirting, finishing ,curing ,material costs,labour charges,tools and tackles etc. all complete as directed by engineer in charge. , providing and laying of premium quality antiskid ceramic floor tiles (size of all tiles shall be 300x300) ofapproved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles, with material costs,tools and tackles,labour charges etc.as per specifications, standards and instructions of engineer in charge. , providingand laying upto300 x 450 mm size coloured glazed ceramic tiles for wall/dado(grade i quality), of approved make & shade including 20 mm thick cementbedding c.m. 1:3, pvc beading with matching colour , pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface with wax polishing complete with material costs,tools and tackles,labour charges as perspecifications and as directed by engineer in charge. , providing and laying pvc roll/tile of approved shade,texture of 2mm thickness homogenous, unbaked,flexible,anti static pvc tiles conforming to bs 2050 table 2, is 3461/3462 in floor,skirting,fixed over base floor/surface by means of a continous coating of rubber adhesive ( as per manufacturer specification) overthe base floor/surface including cleaning the finished surface with approved detergent to remove stains etc. all compelte as directed by engineer in charge.removal of damaged existing membrane to be carried out if required. , providing & forming40mm thick average hard wearing surface with granolithic concrete floor finish (1:1:2) laid in 2.5 m x 2.5 m panels by means of necessary formwork over concrete floor includingmaterials,labour,tools,tackles etc. all complete as per specification, drawings & as directed by engineer in charge. , providing asbestos free everest hitech or equivalent6mm thick corrugated cement sheet roofing in natural stone grey colour and fixing with high corrosion resistant self drilling fasteners and epdm washers by replacing the existing worn out sheet etc. complete ; including cutting to size and shape ,providing laps,scaffolding etc.with all labour,tools as directed by engineer in charge. , providing asbestos free everest hitech or equivalentserrated adjustable ridges for roofing including fixing with accessories like high corrosion resistant self drilling fasteners/epdm washers and or g.i. seam bolts and nuts, g.i. plain and bitumen/ washers including cutting to proper size , scaffolding, etc., for all heights with all labour,tools & tackles complete as directed by engineer in charge. , providing asbestos free everest hitech or equivalentgutterof 600mm overall girth semicircular in shape for roofing including fixing with necessary slope with accessories likegutter guards, clamps,brackets,high corrosion resistant self drilling fasteners/epdm washers and or g.i. seam bolts and nuts, g.i. plain and bitumen/ washers including cutting to proper size , scaffolding,providing provision for fixing rain water downtake pipe etc., for all heights with all labour,tools & tackles complete as directed by engineer in charge. , supplying, transporting, fabricating, erecting and fixing in position colour coated corrugated galvalume sheet of 0.45mm base metal thickness , with colour coating including fixtures, bitumen washers, corner pieces, all necessary accessories, scaffolding etc. complete in all respects at all levels, locations and as perspecifications and direction of engineer in charge. , providing & laying to required slope cement concrete screed of mix 1:1.5:3 (1 cement : 1.5 m sand: 3 coarse aggregates 12.5mm and down graded aggregates) using 53 grade opc inroof terrace etc. laid to required slope and thickness & inclusive of curing/pond curing, brooming with wire brush, finishingetc.all labours, tools and tackles complete as per drawing, specification & as directed by engineer in charge. , providing and laying cool roof s.r.i (solar reflective index)tiles of johnson endura or approved equivalent ,size 300mmx300mm ,white in colour with thickness not less than 10mm, on terraces jointed with suitable cementious water proof grout, laid over suitable tile fixing mortar as per manufacturers specification with required slope, thickness and finishing neat including pointing etc. complete with all tools, tackles, equipments, labour, cement cost etc. as per specifications and as directed by engineer in charge. , providing and laying first quality pressed clay tiles( as per approved pattern not less than 18 mm thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement: 4 msand) mixed with 2% integral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement: 4 m sand) and finishing neat including all tools, tackles, equipments, labour,materials,hacking of concrete,necessary surface preparation,pointing with cement mortar 1:4 mixed with 2 % integral water proofing compound , etc.whereever required , complete as per specifications and as directed by engineer in charge. , providing and fixing white glazed earthenware china wash basin of make parryware/hindware with antisplash rims on 3 sides of 550x450mm sizeincluding approved cast iron/ms brackets , one 15mm dia. cp brass pillar cock, rubber plug with cp brass, 32mm cp waste fitting of standard pattern pipe with 32mm dia. pvc pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by engineer in charge. , providing & fixing white glazed earthernware indian pan type water closetof parry ware orrissa or approved equivalent of size 580x440 mm with integral footrest,includingall fittings, p or s traps, cutting walls, floors making good of same, finishing, soldered joints, making inlet/outlet connection, providing min. 150 mm thick sand cushion, finishing, etc.all complete as directed by engineer in charge. , providing & fixing white wall hungeuropean water closet (ewc) with dual flush cistern of parry ware or approved equivalent make including cistern, cistern lid, antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook, other standard accessories, all fittings and fixturesincluding cutting walls, floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing & fixing white floor mounted european water closet (ewc) with dual flush cistern of parry ware petitieor approved equivalent make including cistern, cistern lid, antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook,bibcock andother standard accessories, all fittings and fixturesincluding cutting walls, floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing and fixing white glazed earthern ware half stall urinal of parry ware niagara orapprovedequivalent, including parryware brand or approved equivalent cp urinal push angle valve, cp brass spreader with 32 mm dia pvc pipe, tee, distribution pipe, brackets etc. making inlet & outlet connections fixing with cp brass screws, finishing, etc. all complete as directed by engineer in charge. , providingandfixing in position white glazed earthern ware vitreous chinadivisional platepartition for urinals of size 350x675x130mmparryware magnum or approved equivalent placedbetweenurinalsanchoring and fixing the divisional plate with fastners and required clamps / fittings, making good of all damaged work, finishing etc., all complete as per specification and as directed by engineer in charge. , providing and fixing20 mm nominal outer dia.sch 40 unplasticised poly vinyl chloride(upvc) pipes, of approved equivalent make with ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb,spacing of jumpers shall be minimum 1mc/c etc. all complete including jointing with bonding solution of approved quality and makeincluding clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , same as sl. no: 610 above, but for 25mm nominal outer dia. pipes , same as sl. no: 610 above, but for 50mm nominal outer dia. pipes , providing and fixing 15 mm dia. nominal bore galvanized iron (gi) pipes complete with gi fittings including trenching and refilling etc. (external work) complete as per directions of engineer in charge. , same as sl. no. 640 above, but for 20mm dia. nominal bore pipes. , same as sl. no: 640 above, but for 50mm dia. nominal bore pipes. , same as sl. no. 640 above, but for 80mm dia. nominal bore pipes. , same as sl. no. 640 above, but for 100mm dia. nominal bore pipes. , same as sl. no. 640 above, but for 150mm dia. nominal bore pipes. , providing and fixing75 mm outer dia. of 6kg/sq.cm poly vinyl chloride(pvc) pipes (exposed on wall) ,including all pvc plain & brass threaded fittings & accessories including fixing the pipe with clamps at 1m spacing. this includes jointing of pipes & fittings with one step pvc solvent and testing of joints complete as per directions of engineer in charge. , same as item no:700 above, but for 110mmouter diameter. , providing and fixing 160 mm dia. rigid pvcpipesas rain water pipes,weep hole pipes etc. with ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg/ sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal borebrass angle valveincluding breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixingapproved cp brass urinal push angle valve of parryware or approved equivalent including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing metro or equivalent approved 15mm nominal bore brass bibcockincluding breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing two way bibcock single lever range with flange of parryware crust or equivalent approved 15mm nominal bore cp including fixingand connections, etc. completeas directed by engineer in charge. , providing and fixing 25 mm nominal bore gun metal gate valve with cast iron (ci) wheel of approved quality (screwed end) including all fittings etc. complete as directed by engineer in charge. , same as sl. no. 770 above, but for 40mm nominal bore gate valve , same as sl. no. 770 above, but for 50mmnominal gate valve , providing and fixing 25mm nominal bore gi union in existing gi pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required as directed by engineer in charge. , same as sl. no.: 800 above, but for 40mm nominal bore gi union. , same as sl. no.: 800 above, but for 50mm nominal bore gi union. , providing and fixing 600 x 450mm mirror of superior glass of parryware or approved equivalent complete with cp brass screws, fastners and washers complete as directed by engineer in charge. , providing and fixing600 mm long cp rodtowel rail of parry ware make or approved equivalent complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour all complete as specified by engineer in charge. , providing and fixing in position approved quality liquid soap dispenser ofparrywareor approved equivalent make, of standard size with snap fittings, including drilling holes, fixing with cp screws all complete as directed by engineer in charge. , providing and fixing c.p. brass shower rose 100mm diameter with 15 to 20mm inlet of parryware or equivalent approved including 230mm shower arm, making inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing of cp brass twin robe hook of parryware/approved equivalent including fixing the coat hook including drilling holes on plastered/tiled wall and doors fixing the coat hook with cp screws including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , providing and fixing in positionstainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheetsupported onm.s. brackets, supply, fixing ofm.s.brackets, fasteners, sinkcock (quarter turn range) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipewith heavy bottle trap of parry ware or approved equivalent make, inlet pipe, drain pipe , rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls where ever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing etc., all complete as directed by engineer in charge. , providing and fixing coloured 10 litre p.v.c low level flushing cistern with manually controlled device(handle lever) deluxe dual flushofparryware or approved equivalent make with all fittings and fixtures complete as directed by engineer in charge. , supplying and laying in position square shaped 600mm x600 mm(grade md 10) medium dutyci manhole frame with lugs and coverincluding breaking of brick masonry or concrete surface to receive frame with lugs and making good the same with cement mortar 1:3 including applying two coats of anticorrosive paint inclusive of all labours and materials etc. complete as per specifications and as directed by the engineer in charge. , supplying and laying custom (prefabricated) pvc floor sumps/ floor traps fabricated out of 110mm dia. 6 kg/cm2 class pvc pipes with inlet and outlets from 40mm upto 75mm, including providing water seal, fixing to a perfect level, laying cement concrete in 1:3:6 mix cp/pvc colour grating with frame at 4mm below finished floor level making holes in masonry or concrete cutting surfaces conveying all dismantled portions and clearing the site,making leak proof joint and testing, etc. complete and as directed by engineer in charge. , making connection of drain or sewer line using pipes of upto 230mm diameter with existing manhole including breaking into and make good the walls, floors with cement concrete 1 : 2 : 4 mix (1 cement : 2 m sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1 : 4 ( 1 cement : 4 m sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. completeas directed by engineer in charge. , providing and fixing window/ventilator/ door glass panes with float glass panes with float glass of thickness 4mm, fixing with necessary pins and best quality putty or with wooden batten as necessary including removing old damaged glass, disposing of the same as directed all labour and materials etc. complete at all heights as directed by engineer in charge. , providing and fixingaluminium extruded section body tubular type universal hydraulic door closer of everest/ dyna/ universal or any other equivalent approved make with double speed adjustment with necessaryaccessories and screws with all labour charges,tools & tackles etc. all completeas directed by engineer in charge. , providing and fixing double action hydraulic floor spring with stainless steel cover plate of minimum 1.25mm thicknessof universal, everest or any other equivalent approved brand and manufacture is: 6315 marked, for doors for all heights includingall labours, tools and tackles ;cost of cutting floors as required, embedding in floors and cover plates with brass pivots and single piece m.s. sheet outer box with slide plateetc. complete as per the directions of engineer in charge. , providing and fixing bright finished brass 100mm mortice latch and lock isi marked with four leverswith necessary screws etc. complete (best make of approved quality) as specified by engineer in charge. , providing and fixing bright finished 125mm brass handles with necessary screws drilling holes in doors, cup boards including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , same as sl. no.: 970 above, but for 75mm brass handles. , providing and fixing in position first quality non reflective type polyester sun control film ofgarware or equivalent approved make of25 micron thickness including cleaning the door/ventilator panes,trimming the edges etc. complete as per the instructions of engineer in charge. , providing and fixing 12mm thick prelaminated particle board with decorative lamination on one side and balancing lamination on other side; flat pressed three layer or graded wood particle board, in panelling fixed in aluminium doors, windows ,shutters and partition frames with chromium platted(cp) brass / stainless steel screws etc. complete as perdirections of engineer in charge. , supplying and fixing24 mm thick pvc panelled door shutter with pvc frame including pvc towerbolts on either sides, pvc handlesincluding metal hinges and all other fittingsetc. complete as per directions of engineer in charge. , providing and fixing anodised aluminium work for fixed portion of doors, windows, ventilators and partitions with extruded built up standard tubular sections/approximate z sections and other sections of approved make, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required pvc/neoprene felt etc. for fixed portion, minimum anodic coating of grade ac 15 shall be provided.aluminium sections shall be smooth, rust free, straight, mitred and jointed mechnically whereever required including cleat angle, aluminium snap beading for glazing/panelling, c.p. brass/stainless steel screws, all complete as per directions of engineer in charge. (glazings and panellings shall be paid separately) , same as sl.no: 1020 above, but for shutters of doors, windows, ventilators including fittings. , providing and fixing in positionupvc doors both single leaf/double leaf white in colour comprising of glass panel minimum 5mm thick and upvc panels of minimum 15mm thickness (doors may be either partly glazed partly paneled or fully panelled)with upvc stiles, rails,frame and accessories holdfasts, hinges, pull handles on both sides, locking arrangement as per requirementincluding labour charges, material cost, tools and tackles all complete as per specifications & as directed by engineer in charge. , providing and fixing in position sliding upvc windows/ventilators (with clear 5mm thick glass), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , designing,supplying and fixing in position approved make chain/gear opearted steel rolling shutters conforming to is : 6248 using 18 gauge ms interlocking laths sections formed out of cold rolled steel strips 0.9mm thick,18mm wide and 1.25mm thick,80mm wide respectively for shutter width upto 3.5m and above 3.5m ; jointless ms channel section for guide ( minimum 3.15mm thick) ms girders,pressed bottom rails,shutter suspension stud shaft with pulley andcage,top rolling springs, locking arrangement including hood,gear operating mechanism and all accessories required and providing two coats of approved make and shade of rust proof synthetic enamel paint over a coat of red oxide or zinc chromate rich primer, etc. all complete as per directions of engineer in charge. , providing and fixing in position single/double leaf hinged type fire proof doorsof radiant or approved equivalent make conforming to is: 3614 with all necessary fittings and fixtures etc. fire proof doors shall have minimum fire rating of 2 hours including 1.20 mm thick stainless steel sheet cladded 46mm thick shutter with infill material honeycomb board complete with stainless steel frame (double rivet – 143 x 57mm) made from 1.60mm thick stainless steel sheet & fixing arrangementsetc. all complete as directed by engineer in charge. stainless steel shall be of grade 304. , providing and fixing isi marked, overall 30mm thickblock board flush door shutters of kutty or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on one side with decorative1mm thick laminate and another side with water proof laminate of archidply or approved equivalentincluding providing and fixingt type second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) including providing wooden filler/sealer, stainless steel lock with status indicator, teak wood lipping, aluminium butt hinges, 3mm thick anodised(anodic coating not less than15 microns) aluminium kicking plate fixed with screws for entire door width on either side of door for a height of 600mm, fixing with door frame,door bush, finishing etc . all complete as directed by engineer in charge. , providing and fixingsecond class teak wooden framesfor doors, windows, ventilators for all heights including all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/rcc by means of 300mm x 25mm x 6mm thick m.s. hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia m.s. dash fastner, painting with two coats of approved shade and make(ici or equivalent) synthetic enamel paint over appoved quality primer coat, finishing etc. all complete as dirercted by engineer in charge. , false ceiling(a): providing and fixing in position 12 mm thick exterior grade boiling water proof(bwp) both sides prelaminated particle board (novapan or equivalent approved make) panels of approved colour and texture to form grids of 600x600 mm and suspension system consisting of aluminium framework with (a) main runners aluminium tee sections of 25mmx35mmsize,1.5mm thickness(b)cross runners aluminium tee sections of 25mmx25mm size,1.5mm thickness(c) perimeter section aluminium angle section 38mmx38mm,1mm thickness all round the perimeter of the ceiling.the grid system is to be suspended by interlocking the main and cross runners @ 600mm max.bothways by means of aluminium angle cleats.the main runners shall be suspended from the ceiling by means of 3mm thick ms flat clamp fixed to main runners @ 1200 max.and fixed to 6mm dia ms hook which again is fixed to ceiling.3mm thick ms flat clamp shall be connected to main runners with 25mm long ms clamp with levelling nut and @ 1200 mm max. the ms hooks shall be suspended from ceiling by means of slotting in 25mmx25mmx3mm thick ms angle,fixed to the slab by 12mm dia. dash fasteners@1200mm c/c.cross runners shall be fixed suitably @max.600mmc/c to form a grid 0f 600mmx600mm.necessary provisions for suspendinglight fixtures etc.,wherever necessary shall be provided .the framework may be suspended from the roof slab at desired height including finishing,making the framework perfectly levelled and aligned etc. all complete as per directions of engineer in charge.all the suspended members shall be anodized(min.15 microns) aluminium frames of standard extrusions .the rate quoted shall include the material costs,labour charges,tools and tackles etc. , false ceiling(b): providing and fixing false ceiling using aluminium composite panel acp 4mm thick (0.5mm thick aluminium sheet on top & bottom sandwiched with 3mm thick core material )confirming to bs 1467 in combination with approved solid and metallic colour panels laminated sandwiched composite panels to a grid made out of anodized aluminium (with 15 micron anodic coating) t sections 35x15x1.5mm size main runners and cross runners 23.5x19x1.5mm fixed to main runners placed 600mm centre to centre both ways so as to form a grid 600mm square.the frameowrk shall be suspended from the ceiling by level adjusting hangers of 6mm dia ms rodfixed to roof slab by means of ceiling cleats.the suspender shall be placed 600x1200 mm centre to centre including fixing to the frame with cp brass screws and applying priming coat of zinc chromate yellow primer.rates are inclusive of scaffolding,frame work ,labour charges,tools and tackles,all material costs etc. complete as directed by engineer in charge. , demolishing pcc work (taking all necessary safety precautions)manually / by mechanical means for all depths and heights belowand above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable materialatdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishing rcc work (taking all necessary safety precautions)manually / by mechanical means for all depth and height belowand above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable materialatdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishingbrick masonry incement mortar (taking all necessary safety precautions) for allheightsabove plinth level including supply of all labours,tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable material atdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishingstone/rubble masonry (taking all necessary safety precautions) for demolition of existing compound wall for the entire heightabove ground level including supply of all labours,tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable materialatdesignated place upto 7 km leadin vaikkadu area as per specification and directions of engineer in charge. , dismantling of structural steel works (bolted/riveted/welded)of all descriptions(taking all necessary safety precautions) for all heights & depths above & belowplinth level including supply ofall tools & tackles, consumables, necessary scaffolding etc. providing temporary bracings as required, cutting gussetplates, bolts, nuts, weldings etc, stacking of serviceable materials at designated location /cpcl storage yard/scrap yardwithin the refinery premises as per direction of engineer in charge. , dismantling and stacking fencing fabric of any material (taking all necessary safety precautions) , including supply of all tools & tackles, necessarypropping, underpinning, cutting, transporting , stackingand handing over the material to cpcl scrap yard inside refinery etc. all complete as specified and directed by engineer in charge. , dismantling bituminous road(taking all necessary safety precautions)manually / by mechanical means for all depths including cutting road taking out soling and metalling,sorting and screening,supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and stacking of serviceable material, disposal of unserviceable materialto spoil heaps within 50mlead all complete as specified and as per directions of engineer in charge . , dismantling ci ,gi,pvc or asbestos drainage pipe with fitting and clamps including scaffolding, staging working platforms all complete including supply of all tools & tackles,stacking material, transporting, loading & unloading and handing overto scrap yard/stores within refinery premises and disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area) as specified and directed by the engineer in charge. , dismantling of water closet, urinals, wash basins & flushing cistern of all types (ci, pvc, viterous china) with fitting and clamps including pipe lines all complete including supply of all tools & tackles,stacking material, transporting, loading & unloading and handing overto scrap yard/stores within refinery premisesand disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area) as specified and directed by the engineer in charge. , demolishing of aluminium partitions/ gypsum/pop/tiled/thermocol false ceiling ,doors, windows, ventilators (steel/wood/aluminium/glass)shutters including, chowkhats, frames, architrave, holdfasts and all other retrieved materials(taking all necessary safety precautions) for all heights above floor level including supply of all labours,tools & tackles, providing necessary scaffolding, propping, underpinning, temporary supports etc.,as per the instruction of engineer in charge, cleaning and stacking of serviceable material like aluminium frames at destined location /cpcl storage yardwithin the refinery area and disposal of unserviceable material atdesignated place(vaikkadu area) upto 7 km lead outside the refinery premises as per specification and directions of engineer in charge. , demolishing of tile work in floors & walls laid in cement mortar for thickness upto 25mm (taking all necessary safety precautions)manually / by mechanical means including supply of all tools and tackles, propping, underpinning, cleaning the siteand disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area)as per specification and directions of engineer in charge. , dismantling of tile work in roofing for thickness upto 25mm (taking all necessary safety precautions)manually / by mechanical means including supply of all tools and tackles, propping, underpinning, cleaning the siteand disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area)as per specification and directions of engineer in charge. , dismantling ofgi/ac/aluminiumroofing sheets including ridges, hips, gutters, etc.in roofing, including suppy of all labours,tools & hooks, transportation and stacking of serviceable materials at destined location /cpcl storage yardwithin the refinery area and disposal of unserviceable material atdesignated place(vaikkadu area) upto 7 km lead outside the refinery premises as per specification and directions of engineer in charge. , chippingof rcc work by chisellingfor all depths below plinth level including supply of all tools and tackles,scaffolding,propping,underpinning etc. exposing, cutting,lapping/welding the reinforcement bars as per drawings and cleaning the same by wire brushing, washing the exposed surfaces,disposal of the unserviceable material to spil heaps anywhere within the plant boundary all complete as specified and directed.(excavation and backfilling if any shall be paid separately under relevant items.) , supplying,handling,transporting to site of work and fixing approved mechanical anchor fastenersms boltsof grade 5.8 or more,galvanisedwith minimum thickness of 5 microns(approved for use in cracked concrete),of 12mm dia at specified positions on concrete floors,roofs,beams( sides and bottom), walls,columns etc. according to manufacturers specifications including all accessories like nuts,washers etc. of required size,testing,necessary scaffolding,drilling of the holes in concrete surface with electric drill,cleaning of holes with air blowout & wire brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed by engineer in charge. , same as item 1260 above, but for 16mm dia. , same as item 1260 above, but for 20mm dia. , supplying,handling,transporting to site of work and fixing approved chemical anchor fasteners consisting of ms threaded rod of grade 5.8,galvanisedwith minimum thickness of 5 microns and chemical (approved for use in cracked concrete), packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors,roofs,beams( sides and bottom), walls,columns etc. according to manufacturers specifications including all accessories like nuts,washers etc. of required size,testing,necessary scaffolding,drilling of the holes in concrete surface with electric drill,cleaning of holes with air blowout & wire brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed by engineer in charge. , same as item 1290 above, but for 16mm dia. , same as item 1290 above, but for 20mm dia. , making pockets/holes of sizes upto & inclusive 200x200x500mm in rcc/pcc works(taking all necessary safety precautions) by chiselling/drilling, including supply of all tools and tacklesetc. cutting of reinforcement bars,cleaning the pockets of all debris etc. all complete at all heights & depths as specified and directed by engineer in charge.scaffolding and disposal of debris shall be paid separately under relevant items. , repairs to existing rcc beams & columns, including chipping and dismantling & removing of loose particles applying cement paste, raking out joints, applying epoxy resin for bonding fresh cocrete to old concerete, filling void portionwith concrete 1:1:5:3 concrete (1cement:1.5 m sand :3 stone agrregates 12mm size) making good as same, including formwork, curing, staging, working platforms labours, tool and tackles all complete as per specifications and directions of engineer in charge. , supplying, transporting, storing, fabricating & erecting in position bolted and / or weldedstructural steel works like angles,channels, beams, plates, pipes, tubes etc.at all heights & levels and locations including all builtup sections/ compound sectionsmade out of rolled sections and / or plates / bent plates inexisting / new structural pipe supports, frames, etc., cutting to required size, straightening/bending if required, edge preparation,cleaning, scrapping & welding ofunsoundjoints in existing structural members, preheating, (including sealing of box section with continuous welding ) finishing edges by grinding , fixing in line and level with temporary bracings,including providing staging, scaffoldings, & working platforms at all heights, and removal of same after erection,including preparing the surface for painting ,surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease etc complete along with providing paint system as follows:(a) applying inorganic zinc silicate coat 50 micron dft(b) two coats of epoxy primer paint 50 micron dft each(c) two coats of anti rust epoxy top coat paint 75 micron dft each as per manufacturers specifications and as directed by engineer in charge. (d) note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after manual cleaningprior to erection as per specifications & as directed by engineer in charge. supply of all materials in contractors scope. , same as sl. no. 1340 above, but for supplying, transporting, storing, fabricating & erecting in position structural steel works alone, excluding painting works but including pre erection painting works as per (d) in sl.no.1340 above. , same as sl. no. 1340 above, but for structural steel painting worksalone excludingsupplying, transporting, storing, fabricating & erecting in position structural steel works and excluding pre erection painting works as per (d) in sl.no.1340. , supplying, transporting, storing, fabricating and fixing in position ms steel inserts (withlugs)asshownin drawing including fabrication to any shape made out of flats, plates, rolled sections, sleeves, pipes etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both plain,reinforced cement concrete members inclusive of adjusting shuttering & reinforcement/any other fixture, welding where ever necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts,& painting with one shop coat of inorganic zinc silicate primer and finsihing with two coats of anti rust epoxy paint of approved brand and colour ,etc complete as perdrawing,specification and direction of engineer in charge. , supplying, fabricating, fixing and keeping in position at all levels and locations threadedm.s. anchor bolts of all diameters andnomenclature including nuts, washers, anchor plates, washer plates, closure plates, pipe sleeves etc. in foundations, pedestals, etc. as directed including handling & transporting, straightening if required, turning from relevant size. m.s. rounds to required diameter, threading, welding, providing necessary templates and auxillary dummy structure, if any, necessary tying and welding, providing necessary templates and auxillary dummy strucutres, if any, necessary tying and welding with reinforcement bars, adjustment of shuttering & reinforcement/any other fixture, greasing exposed metal surfaces, covering bolts and packing the sleeves with jute cloth etc. all complete as perdrawing and specification and direction of engineer in charge. , supply, fabricating, transporting to site and erecting in position ms gates/grills as per drawings using steel confirming to is:2062 / is:1161 including supply and fixing of all materials such as hinges, locking arrangement, pluger bolts, ci wheels and fixtures, ms rail for wheel with anchor etc, all complete as directed by engineer in charge. rate shall include material costs,labour charges,all inserts and embedments essential for smooth operation of the gate. the rate shall also include two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer. , supplying, transporting, fabricating, erecting and fixing in position as per the specifications, electroforged hot dip galvanised gratings (gi coating weight shall be 305gm/sqm as per is 4759) of the approved design and pattern and erecting & fixing of fabricated steel work on operating floors, platforms, stair landings & treads,drain cover etc., at various levels including supply of all gi fixtures like edge plates for treads,clips, studs, bolts, welding if required and nosing for the treads and etc., complete, as per drawings, specifications & as directed by engineer in charge. , supplying galvanised ms chequered plate,transporting ,cleaning & fabricating & fixing on floors as cable trench covers including grinding edges & supplying all bolts,nuts ,washers etc. complete .the galvanised ms chequered plate(6mm to 10mm thick) to be fixed to the supporting beam with help of 12mm dia. counter sunk bolts at 400mmc/c including necessary modifications for supporting structure,drilling holes in plates and supporting structures etc. all complete as per drawings,specifications and directions of engineer in charge. , providing and fixing double scaffolding(cup lock type) on the exterior side, up to three story height made with 40mm dia m.s. tube 1.5m centre horizontal and vertcical tubes joining with cup and lock system with m.s. tubes challies, m.s. clamps and m.s. staircas systems in the scaffolding for woking platform etc. and maintainingit in a serviceable condition for the required durationas approved and removing it there after. the scaffolding system shall be stiffened with bracing and runners, connection with the building etc., whereever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in charge. the elevational area of the scaffolding shall be measured for payment purpose. the payment will be made once irrescpective of duration of scaffolding. , supplying, fabricating, erecting stainless steel works including gratings (ss grade 304 )to required profile and size as filter in drain with necessary fittings including straightening if required, cutting, bending, welding,grouting , cleaning, surface preparation as per specifications etc. all completed as specified and directed by engineer in charge. , providing necessary barricading workswith 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3 m , embedding the same in firm ground etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works.the same will be the property of contractor. , providing and laying to required camber granular base wet mix macadam , comprising of coarse aggregate 53 mm & down size as per specification including preparation of mix in approved mixing plant with controlled addition of water ,spreading with paver finisher or motor grader & rolling with 10 mt roller(vibro roller) in layer of compacted thickness 150mm as directed by engineer in charge. , providing and laying reinforced np3 class (medium duty) rcc hume pipe of 300mm dia. with collars jointed with stiff mixture of cement mortar in the proportion of 1:2(1cement:2m sand)for road crossing etc.including cutting, lowering, laying in position , with proper level, slope , testing of joints etc. as per specifications and directed by engineer in charge. , same as sl. no. 1460 above,but for 450mm diameter. , supplying and fixing at site chain link wire net fencing with chain link fence fabric of 50x50 mm diamond mesh of 2.5mm dia gi innerwire insulated with minimum 1.5mm pvc to achieve outer dia not less than 4mm to intermediate, corner, straining, starting or end post of ms angles/post/strut and one horizontal strand of 8 swg (4mm) dia gi inner wire insulated with pvc for tension in chain link (at middle) , gi staples for fixing chainlink in the intermediate posts and 10mm dia 175mm long hook bolts (threaded portion being 75mm long minimum) for fixing each link of the chain link; with all labour and materials but excluding cost of all ms angle postetc. complete as per drawings and directions of engineer in charge. , supplying, fixing and tensioning in position on rcc posts, 12 gauge, 2 ply, 4points, gi barbed wire designation a 1 confirming to is:278 in horizontal rows for barbed wire fencing etc with necessary gi staples, clips and pins, gi straining bolts and binding wire, etc. complete as per specifications and directions of engineer in charge. , supplying and fixing at site welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint over a coat of primer including cost of materials,labour, tools,tackles all complete as directed by engineer in charge. , concertinacoilfencing: providing and fixing 750mm dia green colour painted razor type concertina fencing with all required clips, pins, etc as per the specifications(each concertina coil piece stretch to 9m length) concertina coil shall be fixed to the m.s. angle with 4 rows of same concertina runner wires over exisiting x type angle supports as per drawings. rate shall be quoted on running metre of compound wall basis. a.diameter of coil: 750mm, number of circles and number of clips are 72 and 180 in each 9m of length. b.central core wire: core wire shall be of 2.6mm diameter made of high carbon spring steel of high tensile strength having minimum galvanizedcoating thickness equivalent to 230 grams per sq.m. c. razor strip: 0.5mm thick hot dip galvanized and of width 19mm having series of barbed punched all along the length at regular intervalshaving minimum galvanized thickness of 12 microns. hardness of tape should be between 137 180 vpn (victor penetration number) d. clips: 1.5mm thick made out of stainless steel. e. runner wire: shall be of same specifications as of central core wire. , supply of unskilled class i labourto carry out petty works not assessable for measurements/minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits andhand tools. , same as sl. no. 1520 above,but for supply of unskilled class ii labour , same as sl. no. 1520 above,but for supply of mason. , same as sl. no. 1520 above,but for supply of plumber. , same as sl. no. 1520 above,but for supply of carpenter. , same as sl. no. 1520 above, but for supply of stone cutter. , same as sl. no. 1520 above, but for supply ofwelder/cutter/grinder including all consumables, necessary machineries, tools and tackles , ppeand with valid cpcl welders certificate. , same as sl. no. 1520 above, but for supply offitter including all consumables, necessary machineries, tools and tackles and ppe. , same as sl. no. 1520 above, but for supply ofrigger. , supply of jcb on hire basis on all days including sundays on 8 hrs.shift including driver,assistant /fuel/oil/lubricants /all consumables etc. complete. the quoted rate should include mobilization, operator crews/driver /assistant cost,tools, tackles etc., as directed by the engineer in charge. , supply ofpoclain pc 200on hire basis including fuel/oil/lubricantsfor excavating , levelling to required slopes and dumping at designated places within thesite premises. the quoted rate should include mobilization,operator crews/driver cost, loading, transporting, unloading, tools, tackles etc. complete as directed by engineer in charge. , same as sl. no: 1620 above, but for supply of crawler mounted dozzer. , same as sl. no: 1620 above, but for supply of tippers of capacity not less than 10 cu.m , same as sl. no: 1620 above, but for supply of taurus/approved equivalent tippers of capacity minimum 15 cu.m , same as sl. no: 1620 above, but for supply of mini poclain 30. , same as sl. no: 1620 above, but for supply of tractor mounted dozzer . , supply of 20 feet trailer with tractor on hire basis on all working days from monday to saturday on 8 hrs.shift ,inclusive ofdriver,one assistant,all consumables like diesel etc.,with all safety precautions within cpcl refinery premises.the quoted rate should include mobilization,operator crews/driver /assistant cost, loading, transporting from site to scrap yard within refinery premises, unloading,tools, tackles,wire ropes,pulley blocks,belts,chains etc. for lifting,aligning,tying,stacking etc. all complete as directed by engineer in charge. , same as sl.nono. 1680 above but for tractor with trailer of minimumcapacity 2.5 cu.m. , same as sl.nono. 1680 above but for 40 feet trailer with tractor . , supply of front cabin hydraof minimum capacity12 t on hire basis on alldays including sundays on 8 hrs.shift ,inclusive of driver,one assistant,all consumables like diesel etc.,with all safety precautions within cpcl refinery premises.the quoted rate should include mobilization,operator crews/driver /assistant cost, loading, transporting, unloading, labour, tools, tackles etc. complete as directed by engineer in charge. , supply ofskylift of minimum capacity 300kg for maximum working height upto 20m with high manoeuvrability and hydraulically operated on hire basis on alldays including sundays on 8 hrs.shift with all safety precautions within cpcl refinery premises. the quoted rate should include mobilization,operator cost, diesel charges,transporting, demobilisation etc. complete as directed by engineer in charge. , supply of 400amps welding rectifieron hire basis on alldays including sundays on 8 hrs.shift with all safety precautions within cpcl refinery premises.the quoted rate should include mobilization, transporting, demobilisation costs etc. complete as directed by engineer in charge. , same as sl.no1730 above but for supply of dg set of minimum capacity 63kva including diesel charges . , supply of gully sucker truckon hire basis for removal of oil sludge with inbuiltvacuum suction using super suction machine and tanker of minimum 6 kl capacity with necessary suction/ delivery hoses of sufficient lengths and personnels of 2(two) nos. in addition to a driver and cleaner to handle the floating oils on storm water pond/drains on regular basis on all working days from monday to saturday (8 hours/day starting from the reporting time at site). the quoted rate should be for supply of one gully sucker truck as specified above on hire basis, inclusive of charges towards fuel/oils/lubricants, operator crews /driver costs, all labour, tools, tackles, mobilization, loading, transporting, unloading in the refinery premisesas directed by the engineer in charge. , pumping out watercaused by natural ground water sources, broken water mains of drains adn the like using diesel/ electric power driven self priming pumps of adequate capacity with necessary discharge and suction hoses to required length including hire, fuel/oil and operator cost etc. complete as directed by engineer in charge. , providing and bunding with sand filled bags of min 0.5 cu.ft. in capacity for maintaining and diverting the flow of water etc. including supply and filling of sand, stitching of the bags, carting to site of work to any distance, keeping position as directed, plugging holes and paddling etc., with all labour, materials, tools plants including the cost of sand and empty gunny /polythene bags etc. complete as directed by engineer in charge. , cleaning of man holes dechocking and flushing of industrial ows/fecal sewage lines of different diameters between two manholes with drain cleaning rods, bamboos strips flushing with water and compressed air, removal of sludge and disposal ofthe same at identified areas within the refinery premises upto a lead of 2km radius, as directed by the engineer in charge all labour including removing and refixing the cover slabs in position, transportation of required machinery tools, plants etc., complete taking all safety precautions as specified. thecompressed air and water at one point shall be supplied free of cost, if required.for catch basins/pits/inspection/gully trap chambers etc. , providing and laying 60mm thick factory made cement concrete interlocking rubber mould paver block of m30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in two or more colour and pattern over and including 50mm thick compacted bed of coarse sand filling the joints withsand etc. all complete as per the direction of engineer in charge. , supplying, transportation, installing, dismantling and removing of interlocking type temporary steel sheet piles with crane, vibro hammer/pile driving machinery of adequate capacity and other ancillary equipment, including driving and joining the sheet piles as per specification up to levels as per specifications & directed by eic. installed sheet piles are temporary and shall retain the earth, provide excavation support for a depth of 6m from ground level and protection against water seepage & sliding of earth during construction activities.including supply of all materials, steel members, welding, strutting, tie members supporting, labour, plant & machineries, etc. all complete as directed by engineer in charge. (note: 1. method of measurement for payment will be the actual horizontal limit of temporary sheet piling installed and accepted, and the vertical limit as measured from the bottom of the exposed face of the sheeting to the top of the retained earth behind the sheeting. 2. the steel sheet piles shall be supplied by the contractor and shall remain the property of the contractor). , providing and fixing20 mm nominal outer dia chlorinated poly vinyl chloride(cpvc) pipes, of approved equivalent make withholder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb,spacing of jumpers shall be minimum 1mc/c etc. all complete including jointing with bonding solution of approved quality and makeincluding clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , same as sl. no: 1810 above, but for 25mm nominal outer dia. pipes , providing and laying of hot applied thermoplastic compound 2.5mm thick asroad marking strips including reflectorising glassbeads @ 250 gms per sq.m area,thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35. the finished surface to be level uniform and free from streaks and holes etc. complete as per morth specificationand as directed by engineer in charge. , providing and fixing glow studs of size 100x20 mm made of heavy dutybody shall be moulded asa (acrylic styrene acryloretrite ) or hip (highimpact polystyrene)having electronically welded microprismaticlens with abrasion resistant coating as approved by engineer in charge.the glow stud shall support a load of 13635 kg tested in accordance with astm d4280. the slope of retroreflective surface shall be 35(+/ 5)degress to base .the reflective panels on both sides with at least 12 cm of reflective area up each side. the luminance intensity should be asper thespecification and shall be tested as described in astm i: 809 as recommended in bs: 873 part 4 : 1973. the studs shall be fixed to the road surface using the adhesive conforming to is, as per procedure recommended by the manufacturer complete and as per direction of engineer in charge. , supply of diesel run vehicle mounted hydraulic operated high pressure suction cum jetting sewer cleaning machineon hire basis on alldays including sundays on 8 hrs.shift fitted with pumps having suction tank mounted including water jetting pipes & accessories, suction hose pipe, discharge pipes, all materials, consumables, tools & tackles, etc.,skilled driver cum operator, required helpers for carrying out the jetting / suction operations, cleaning of ows pits, pipelines and manholes etc. as per the directions of engineer in charge. rate includes mobilization, demobilization, charges for hoses of minimum length of 100m. => limited...

Indian Rare Earths Limited - Tamil Nadu

32770072 dismantling and removal of r.r. masonry sl.no.1 of scope of work dismantling and removal of r.r. masonry / brick masonry / plain cement concrete work, etc. upto 5m height and dumping the debris within a lead of 500m etc. complete as per the direction of engineer in charge. 2 2 dismantling and removal of rcc foundation sl.no. 2 of scope of work dismantling and removal of rcc foundation / column / slab / beam, etc. in all heights upto 8m from floor level including all necessary scaffolding and dumping the debris within a lead of 500m etc., complete as per the direction of engineer in charge. 3 3 earthwork excavation for foundation sl.no. 3 of scope of work earthwork excavation for foundation in all types of loose / hard soil and depositing the spoils with an initial lead of 20m and lift upto 2m including refilling etc., complete as per the direction of the engineer in charge. 4 4 supplying, providing and laying pcc 1:4:8 mix for foundation sl.no. 4 of scope of work supplying, providing and laying pcc 1:4:8 mix for foundation / flooring work using 40mm and below grade hard blue granite jelly including all form works, mixing, laying, compaction, consolidation and curing, etc. complete as per standard specifications and as directed by the engineer in charge. 5 5 supplying, providing & laying rr masonry foundation sl.no. 5 of scope of work supplying, providing & laying rr masonry foundation / wall / retaining wall in cement mortar 1:6 for construction of wall using hard blue granite stone, etc. complete from 1m below ground level to 3m height above ground level with neat finishing including proper pointing & necessary scaffolding work etc complete as per standard specifications and as directed by the engineer in charge. 6 6 supplying, providing and laying dry rubble masonry for soak pit sl.no. 6 of scope of work supplying, providing and laying dry rubble masonry for soak pit for construction of wall using hard blue granite stone, etc. complete as per standard specifications and as directed by the engineer in charge. 7 7 supplying, providing and laying brick masonry sl.no. 7 of scope of work supplying, providing and laying brick masonry in cm 1:6 using well burnt country brick of minimum size 22.9x11.2x7cm for foundation / kerb wall / wall upto 4.5m height from ground level including all scaffolding, staging, curing, etc. complete complying with standard specifications and as directed by the engineer in charge. 8 8 supplying, providing and laying pcc 1:2:4 mix for foundation sl.no. 8 of scope of work supplying, providing and laying pcc 1:2:4 mix for foundation / flooring work / kerb wall drainage wall using 20mm and below grade hard blue granite jelly including all form works, mixing, laying consolidation and curing, etc. complete as per standard specifications and as directed by the engineer in charge. 9 9 supplying, providing and fixing twisted reinforcement sl.no. 9 of scope of work supplying, providing and fixing twisted reinforcement is 1786 hysd bars fe500d / fe550d ( tmt bars tata / agni / jsw ) including fabrication, cutting, bending, cold tying, with overlapping to the standard length wherever necessary and placing the reinforcement in position as per the direction engineer in charge including binding, provision of spacer bars, cover blocks and all other incidental charges, etc. complete for all rcc works as per standard specification and as per the direction of engineer in charge. 10 10 supplying, providing and laying cement concret 1:1.5:3 sl.no. 10 of scope of work supplying, providing and laying cement concrete 1:1.5:3 for rcc works using 20mm and below grade hard blue granite jelly with specified reinforcement and all mixing, laying, compaction, leveling, consolidation and curing, etc., including the cost of centering / shuttering work, complete as per specification and as directed by engineer in charge. 11 11 supplying, plastering with cm 1:4 mix 15mm thick sl.no. 11 of scope of work supplying, plastering with cm 1:4 mix 15mm thick one coat floated hard & trowelled smooth etc for floors & walls upto 8m height with neat finishing and necessary grouting, etc. complete complying with standard specifications and as directed by the engineer in charge. 12 12 supplying, plastering with cm 1:3 mix 12mm thick sl.no. 12 of scope of work supplying, plastering with cm 1:3 mix 12mm thick one coat floated hard & trowelled smooth for rcc beam, column, ceiling upto 8m height with neat finishing and necessary grouting, etc. including all scaffolding, etc. complete complying with standard specifications and as directed by the engineer in charge. 13 13 supply of paints and painting two coat sl.no. 13 of scope of work supply of paints and painting two coat with emulsion paint ( asian / berger / nippon ) 1st quality of approved shade for the external / internal masonry surface upto 10m height from ground level, including thorough scrapping, cleaning, removal of dirt, all tools & tackles, sandpaper and scaffolding arrangements, etc. and applying wall primer & putty touch up works wherever required etc complete as directed by the engineer in charge. 14 14 supplying, providing and fixing sintex pvc door sl.no. 14 of scope of work supplying, providing and fixing sintex make pvc door of size 750x2100mm including hinges, handle and locking arrangements, etc. complete as directed by engineer in charge. 15 15 supplying, providing and fixing steel door sl.no. 15 of scope of work supplying, providing and fixing steel door of size 1.20x2.10m consisting of heavy type 40mm g.i. square pipe ( is:4923 ) all round and middle two horizontal 25mm g.i. square pipe at 100mm centre to centre vertical on the top half portion and bottom portion covered with 2mm thick aluminium chequered sheet fixed with 25x5mm ms flat welded with outer frame on both sides of aluminium sheet including all supply and fixing ms kondy, locking arrangements and painting the gate with two coats of enamel paint over a coat of zinc chromate enamel yellow base primer, etc. complete as directed by engineer in charge. 16 16 supplying, providing and finishing the floor with anti skid ceramic tiles sl.no. 16 of scope of work supplying, providing and finishing the floor with johnson / somany / kajaria make anti skid ceramic tiles of size 300x300mm of approved quality and shade in cm 1:3 ? 15mm thick and pointing the tiles with matching colour cement, etc. complete as per the direction of the engineer in charge. 17 17 supplying, providing, laying, dadoing the walls tiles sl.no. 17 of scope of work supplying, providing, laying, dadoing the walls with johnson / somany / kajaria make ceramic wall tiles of size 450mmx300mm of approved quality and shade fixing with cm 1:2 ? 10mm thick, etc. including neat cleaning, grouting and finishing with shaded colour joint filler etc. complete as per the direction of the engineer in charge. 18 18 supplying, providing and fixing rcc jally sl.no. 18 of scope of work supplying, providing and fixing rcc jally of size 0.60x0.45m.as per the direction of the engineer in charge 19 19 supplying, providing and and laying 20 / 25mm cpvc pipe sl.no. 19 of scope of work supplying, providing and laying 20 / 25mm cpvc astrol / ashirvad pipes including all specials cpvc / brass such as bend, elbow, reducer, tee, solvent cement, mta & fta etc. complete as per the direction of engineer in charge. 20 20 supplying, providing and laying 20 / 25 / 32mm id pvc pipes sl.no. 20 of scope of work supplying, providing and laying 20 / 25 / 32mm id pvc finolex / ashirvad / astral superthick pipes including all specials such as bend, elbow, reducer, tee, solvent cement, etc. complete as per the direction of engineer in charge. 21 21 supplying, providing and laying 40 / 50 / 63mm dia idpvc pipes sl.no. 21 of scope of work supplying, providing and laying 40 / 50 / 63mm dia id pvc finolex / ashirwad / astral superthick pipes including all specials such as bend, elbow, reducer, tee, solvent cement etc. complete as per the direction of engineer in charge. 22 22 supplying, providing and laying 110mm idpvc pipes sl.no. 22 of scope of work supplying, providing and laying 110mm dia id pvc finolex / ashirwad / astral ( 6kg ) pipes including all specials such as bend, elbow, reducer, tee, solvent cement, etc. complete as per the direction of engineer in charge. 23 23 supplying, providing and fixing bib tap sl.no. 23 of scope of work supplying, providing and fixing the cp sanitary fittings: bib tap / pillar tap as per the direction of engineer in charge. 24 24 supplying, providing and fixing urinal sl.no. 24 of scope of work supplying, providing and fixing the cp & sanitary fittings: white parryware urinal niagara with spreader and waste pipe including suitable azhirwad / supreme / high count make pvc gully trap, urinal bracket, urinal cock, etc. as per the direction of engineer in charge. 25 25 supplying, providing and fixing urinal partition slab sl.no. 25 of scope of work supplying, providing and fixing the cp & sanitary fittings: urinal partition slab i.e. both side polished and corner grinded ( for smooth finish ) marble slab of size 600x1200mm ? 20mm thick, with neat finishing etc. complete as per the direction of the engineer in charge. 26 26 supplying, providing and fixing wall hung basin sl.no. 26 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware duke wall hung basin, colour: white wash basins with necessary accessories ( waste coupling, waste hose, etc. ) as per the direction of engineer in charge. 27 27 supplying, providing and fixing indian toilet sl.no. 27 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware ceramic sanitary ware indian toilet / orissa pan with required trap and slim flush tank combo pack ( standard, white ) ( 23 inch indian toilet ) etc.as per the direction of engineer in charge. 28 28 supplying, providing and fixing europeon closet sl.no. 28 of scope of work supplying, providing and fixing the cp & sanitary fittings: elite [ europeon closet ] white parryware single piece suite 525x380x400mm including seat cover, with required trap and slim flush tank ( standard, white ) and fittings as per the direction of engineer in charge. 29 29 supplying, providing and fixing 20 / 25mm brass ball valve sl.no. 29 of scope of work supplying, providing and fixing the cp & sanitary fittings: 20 / 25mm brass ball valve of heavy type including fixing, etc. as per the direction of engineer in charge. 30 30 supplying, providing and fixing 500 ltrs water tank sl.no. 30 of scope of work supplying, providing and fixing 500 ltrs. capacity sintex water tank with all inlet and outlet pipe fitting arrangements and 20mm brass float valves, etc., complete as per the direction of the engineer in charge. 31 31 supplying, providing and fixing health faucet sl.no. 31 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware health faucet with hose & hook as per the direction of engineer in charge. 32 32 supplying, providing and fixing towel rail sl.no. 32 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware towel rail 600mm as per the direction of engineer in charge. 33 33 supplying, providing and fixing angle cock sl.no. 33 of scope of work supplying, providing and fixing the cp & sanitary fittings: parryware angle cock as per the direction of engineer in charge. 34 34 engagement of labour ( mazdoor ) for miscellaneous work sl.no. 34 of scope of work engagement of labour ( mazdoor ) for miscellaneous work as directed by the engineer in charge. ( required materials will be issued by company on free of cost ) ....

Military Engineer Services - Tamil Nadu

32767686 provision of toilet neat main gate entrance of age ( i ) r&d office at cvrde avadi 1 excavation in trenches n. exc 1.5 m in depth for foundation etc and getting out in hard / dense soil. 2 surface excavation in hard dense soil n.exc ( not exceeding ) 30cm deep and averaging 15 deep and getting out in hard / dense soil. 3 m & l for pcc type d2 1:4:8 ( 40 mm graded aggregate ) cement concrete in foundations, filling, concrete bed to drain pipes and mass concrete 4 m&l brick work with sub class ‘b’ bricks curved on plan exc 6 m mean radius built in cement mortar 1:6 5 m&l brick work with sub class ‘b’ bricks curved on plan exc 6 m mean radius built in cement mortar 1:4 6 m&l brick work with sub class ‘b’ bricks curved on plan exc 6 m mean radius built in cement mortar 1:4 in half brick thick walls 7 returning filling including spreading, levelling watering and well ramming in layers not exc 25 cm thick complete 8 removal of excavated soil exe 250m but not exe 500 m and deposited where directed. 9 m & l for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; verticle or to batter fair finish surface. 10 m & l for formwork to sides of pillars, posts, struts, piers, columns and stanchions fair finish surface 11 m & l for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc fair finish surface 12 m&l for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick ( horizontal or sloping ) 13 m & l formwork to chullah hoods, chajjas, troughs and similar items including edges fair finish 14 form work to edges of concrete slabs exc 10 cm but not exc 20 cm thick 15 m&l tmt bars 10mm dia & over cut to length bent to shape required including cranking, bending spirally for hooping for columns hookingends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed. 16 all as per srl item no 1.14 here in before but6mm to 8mm dia and stirrups complete all as specified and directed. 17 m&l for rcc m30 in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concreteall as specified and as directed. 18 m&l forrcc m30 in columns, pillars, piers, posts and struts complete all as specified. 19 m & l for rcc m30 in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified. 20 m & l for rcc m30 in slab supported on walls, beams, and column in floors, roofs, landings, balconies, canopies, deck slabs and inshelves, chajja complete all as specified. 21 m & l for rendering 15mm thick cement mortar in two layers i.e 10mm in cm 1:6 and5mm in cm 1:4 mixed with with approved water proofingcompound as per manufacturer instruction on fair faces of brick work or concrete surfaces.note: wpc measured and paid separtely. 22 m&l rendering 10mm thick cement plaster on ceiling surfaces in cement mortar 1:4 finished fair and evenwithout using extra cement complete all as specified 23 m&l rendering 12mm thickin cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified. 24 m&l non skid glazed ceramic coloured ( light colour as approved ) tilesof size 300x300x7 8 mm thick as in flooring set and jointed in neat cement slurry over & including 15 mm thick screed in cement mortar ( 1:6 ) as in floors / sub floors and pointed in white cement with pigment to match the colour of tiles complete all as specified. 25 m&l glazed ceramic coloured tiles in vertical surface 350x 250x 7mm / 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 1:4 cm 10mm thick rendering rough finishedto recive tiles as in skirting / dado. 26 m&l granite galaxy 20mm thick factory polished fixedwithcement slurrypointing with coloured pigment to match the granite including cutting to shape, grinding, polishing bulnosing etc in floors with 15mm thick screed bed in cement mortar ( 1:6 ) all as specified anddirected by the engineer in charge. 27 m & l 75mm thick pccd2, 1:4:8 ( 40mm graded aggregate ) in subbase offlooring complete all as specified. 28 m &l for broken stone hardcore of gauge n exc. 63mm, broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified. 29 m&l for cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by engr in charge and complete all as specified. 30 m&l rendering 15 mm thick screed / cement plaster in cm 1:3 with wpc on rcc surfaces of roof / brick walls finished fair and even while the concrete is green. note : wpc shall be measured and paid seperately. 31 supply only integral water proofing compound. 32 m&l for app based polymeric membrane minimum weighing 3.5 kg / sqm and minimum 3mm thick reinfored with polyster non wooven fabric ( wt not less than 160gm / sqm ) laid over primed surfaces includingbituminous primer conforming to is 3384applied @ 0.3 ltr / sqm byby forced all as specified and directed.four course roof treatment consist of as under: ( i ) applying one coat of bituminous primer conforming to is 3384 @ 0.3 ltr / sqm. ( ii ) laying of app based membrane as specified thickness and weight. ( iii ) applying one coatbitumen grade 85 / 25@1.2kg / sqm. ( iv ) applying two coataluminium paint @100ml / sqm. 33 s&f solid pvc door frame of size 50mmx47mm made out of 5mm plain colour pvc sheetreinforced with ms square tubes s&f opening as per specification & drawings complete all as specified. 34 s&f factory made soild pvc moulded door shutter 28 to 30mm thick ( stiled ) with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face and 2mm plain colour pvc sheet on back face with particle board core. 35 s&f 125mm long ptmt butt hinges fixed with necessary screws powder coated any colour complete all as specified and directed. 36 s&f 150mm long ptmt handles powder coated any colour oval type complete all as specified coloured 125 mm long fixed all as specified and directed. 37 s&f 150mm long ptmt barrel tower bolts powder coated any colour complete all as specified and directed. 38 s&f 250mm long aluminum sliding door bolt powder coated any colour, with hasp and staple bolt type all as specified and directed. 39 supply and fix anodised aluminium, powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. 40 s&f alumnium powder coated louvers ( movable arrangement in pair ) for ventilators including locking arrangement complete all as specified and as directed 41 s&f figured glass coloured pin headed type 4mm thick fixed to aluminium lovers in strips width not exceeding 80mm all as directed. 42 m&l for pvc ( swr ) floor trap 75 mm dia , including 40mm dia hdpe pipe up to the trap of bath room and jointing with solventwith outlet pipes, stainless steel grating etc fixed all as specified. 43 m&l pvc ( swr ) gully trap 125 / 110 mm, setting and jointing with solvent cement with outlet pipesand pcc 1:2:4 filling around trap and 25mm thick coverslab ( size as directed by eic ) complete all as specified. 44 s&f of 110 mm bore pvc ( swr ) pipes single socketed, in any length with rubber ring joints, fixed and laid in trenches / floors including distance pieces complete all as specified and directed. 45 s&f of 75 mm bore pvc ( swr ) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in swr pipes complete all as specified and directed. 46 s&f 110 mm pvc ( swr ) bend of any radius 47 s&f pvc ( swr ) junction single, ( single t ) equal or unequal for 110mm dia pipe 48 s&f 110 / 75 mm dia pvc ( swr ) reducers connected to door bend with access door complete all as specified 49 s&f 110 mm trap p or s trap pvc ( swr ) complete all as specified. 50 s&f 75 / 110 mm dia pvc ( swr ) vent cowl. 51 s&f vitreous china squatting pan, orissa pattern, size 580x440mm white / coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti syphonage pipe, etc. fixed complete all as specified. 52 s&f pvc 10 ltr. capcityvalveless syphonic action type, flushing cistern, low level, white / coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc with all neccassary fittings complete all as specified directed. 53 s&f in 15 mm size pvc connections with ptmt nuts of 450 mm long complete all as specified. 54 s&f vitreous china urinal, bowl type, coloured , flush pipe and waste pipe including providing and fixing plugs, bedding urinal against wall in cm 1:2 securing urinal to plugs fixing with brackets, flush pipe, grating and union for 32mm dia pvc pipe discharge pipe connection to drain etc. 55 s&f urinal spreader of ptmt any colour for fixing with 15 mm dia pipe ( minium weight 60gms ) 56 s&f wash hand basin flat back 550x400mm vitreous chine ( white ) with cantilever brackets embedded in concrete block including the following and fixed in repairs complete all as specified ( a ) brass chromium plated waste coupling 32mm bore size ( b ) waste pipe pvc 32mm bore ( c ) angle iron / cast iron brackets ( d ) cp fancy type pillar cock 15 mm dia. 57 s&f 600x 450 mm leveled edged mirror, 5mm thick of selected quality glass mounted on hard board covered with pvc moulding as per sample kept in ge office and fixed to wooden plugs with chromium plated brass screwed all as directed. 58 m&l soap shelf, pvc white / colour appx size 450 x 125 x 40mm ( as per sample ) . make: prayag or equivalent 59 s&f in repar tubular towel rail 20mm dia d type60cm long between flanges brass chromium plated. 60 s&f bib taps, cp, fancy type screwed for 15mm bore of iron pipe or for brass ferrule and fixed all as specified. 61 s&f bathroom cabinet pvc with mirror suitable for to keep the bathroom items, size 400 x 500mm, white colour all as specified. make : priyag ( cat. no 554 ) 62 s&f stop valves, fancy type, cp with long shank and cup ( concealed typee ) , screwed both ends for 15mm bore of iron pipe or for union and fixed all as specified. 63 s&f gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 15mm bore pipe all as specified and directed. 64 s&f gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 20mm bore pipe all as specified and directed. 65 s&f in mild steel galvanized tubing 15 mm bore medium grade with fittings to walls, ceiling or laid on floor all as specified. 66 s&f in mild steel galvanized tubing 20 mm bore medium grade with fittings to walls, ceiling or laid on floor all as specified. 67 s&f ofrotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) 1000 ltr capesity hoisted and fixed in position all as specified including ball brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe complete all as specified and directed. 68 m&l preparing new plastered surfaces and applying two coats of white wash on soffits / ceilings etc; complete all as specified or as directed. 69 preparation of new plastered surface and apply two coat of cement base paint over a coat of primer with 2mm thick wall care putty complete all as specified. 70 preparation of newly plastered surfaces of walls and applying two coats of distemperoil emulsion over a coat of chalk whiting, on plastered surfaces with 2mm thick wall care putty complete all as specified. 71 m&l chequered cement colouredconcrete tiles 300mm x 300mm x 25mm, set, jointed and pointed in thick neat cement slurry in floors and pointed with white cements and pigments andincluding 15 mm thick screed in cement mortar ( 1:6 ) as in floors / sub floors and pointed in white cement with pigment to match the colour of tiles complete all as specified. 72 cutting existing galvanized ironwater supply pipe line up to 100 mm dia for inserting suitable size gi tee and socket of size 20mm dia for taking branch connection complete all as specified.note: excavation shall be measured and paid seperately. 73 m&l of 150mm bore salt glazed stone ware pipe grade ‘a’ as in trenches at any depth complete all as specified ( excavation , earth work & concrete shall be measured and paid separately ) . 74 m&l pcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate as in benching for manholes, bands , coping , bed plate etc with slightly chamfered or rounded angles including necessary form work, if any, and finishing exposed surface even and smoothwithout using extra cement 75 extra for forming fair finish to drain or channel 30cm internal girth in cement concrete using extra cement inl. forms moulds / mitred stopped ends etc. 76 m & l precast rcc 1:2:4 type b1 using 20mm graded crushed stone agg as in manhole cover slabs, of any thickness, size or shape incldg necessary form work, finished concrete surfaces fair & even in cm all as specified and directed by engr in charge. 77 cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( 1 / 2 round or 3 / 4 section ) in cement concrete 1:2:4 type b 1 smooth finished, and reforming bench ing as required ( internal dia of pipe in 150mm ) 78 m&l for point wiring with pvc insulated, frls pvc unsheathed, two single core, stranded, copper conductor cable 1.5 sqmm size, 1100v grade, drawn into and including concealed rigid non metallic pvc conduit not less then 20mm wide, isi marked with 1.5 sqmm unsheathed, stranded copper frls cable for continuous earth wire and including pressed modular metal concealed terminal boxes of reqd size and suitable size inner frame with outer cover suitable for modular switches / sockets / regulators all as specified & directed for the folowing : ( a ) one light / fan controlled by one switch 79 s&f switch piano flush type, 6 amps, 230v ac, single pole, one way. 80 s&f ceiling rose, surface type, bakelite 65x50mm three terminal 81 s&f batten 4 feet led tube light fitting 18w high lumen efficiency, min 5700k and extruded aluminium body with suitable electronic driver, 230vwith all accessories pre wired, connecting up with and including twin core twisted flexible copper cable complete inclluding taking down unserviceable ftl fitting any type any watts all as specified and directed.make: havells / wipro / philips 82 s&fbatten 2 feet led tube light fitting 10w high lumen efficiency, min 5700k and extruded aluminium body with suitable electronic driver, 230vwith all accessories pre wired, connecting up with and including twin core twisted flexible copper cable complete inclluding taking down unserviceable ftl fitting any type any watts all as specified and directed.make: havells / wipro / philips 83 sub main wiring with 2 runs of single core 2.5 sqmm 1100 volts grade, frls pvc insulated, unsheathed cable, copper conductor, multistranded drawn through and incl provision of isi markedpvc conduit 20mm dia medium grade surfcaein walls / roofs / floors etc., including provision of one run frls pvc insulated 2.5 sqmm copper conductor as earth continuity conductor and connecting to common earth dolly incl taking down u / s aluminium wiring complete all as specified and directed. note: two runs of 2.5sqmm cable, one run of earth continuity conductor shall be measured as one unit length and pvc conduit shall be measured under relevant items. 84 supply and fix ventilating fans ventil air dx white 250mm sweep, 230 / 240 volt mounting ring and louvers and shutters with clamp sets, nuts and bolts suitable for ventilatort fansincluding provn of connecting cable 1 sqmm, 3 core, pvc insulated all as specified and directed. 85 supply and fixing inof energy efficient led building security fitting of not less than 30 watt, epoxy powder coated pressure die cast aluminium housing and toughened glass with ip 66 degree of protection, system luminous efficiency morethan 100 lumens / watt and pf>0.9 with voltage range 140 to 270 volt, fitting should be provided wih inbuilt 10 kv minimum surge protection, short circuit and over voltage protection facility for driver and fitting including making electrical connection for cable connection complete all as directed. note : cable for connection of led light fitting andincluding mounting bracket of gi pipe 32 mm bore bend to shape with 2 nos ms flat 32 x 3 mm thick with suitable nuts & bolts for mounting the fitting shall be is included in this item and nothing shall be paid extra on this account 86 s&f sheet metal enclosure ( mcb db ) , single phase and neutral with suitale amps rated bus bar, double door type, 240 volts 4 way 87 s&f mcb single pole, 240 volts, 6amps, c series, 10 ka breaking capacity & connection complete all as specifed and directed. 88 s&fmcb single pole & neutral10amp, 240 volts, c series, 10 ka breaking capacity & connection complete all as specifed and directed. 89 s&f fix inearthing complete with galvanised steel earth plate electrode 60x60cm x 6.0mm thick burried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to and including using of 4 mm gi wire as earthing leadby means of bolts, nuts, check nuts and washers of galvanised steel , connected to earthing test point, all as specified & indicated, including testing on completion including earth work and excavation in any type of soil / rock, pcc 1:3:6 type c1, earthing chamber, precast rcc slab 50mm thick in cement concrete 1:2:4 type b1 reinforced with welded steel wire febric weight hot less than 4 kg / sqm, funnel with gi watering pipe of 20mm bore, medium grade wire mesh and lugs, gi protection pipe of 15mm bore light grade upto 7.50 mtr long test point etc all as specified and directed....

Chennai Petroleum Corporation Limited - Tamil Nadu

31710300 tender for miscellaneous civil and structural works for coke handling system in manali refinery of cpcl miscellaneous civil and structural works for coke handling system in manali refinery of cpcl , earthwork excavation in all types of soil depth up to 1.5 m, including soft or hard murrum, but excluding sofr and hard rock, using mechanical means ( hydraulic excavators ) / manually including clearing away of vegitations, shrubs and debris, cutting and dressing of slides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated / sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated materials within a lead of 100m, as directed including shoring and strutting and providing temporary supports to existing service lines like water pipes, product pipes, sewage pipes, electric overhead and underground cables, cable trenches, etc. all complete as per the specifications and directions of engineer in charge. , same as item no. 10 above, but for depth beyond 1.5m and upto 3.0m. , providing & laying dry rubble soling ( hard core ) with 20 to 40 mm size metal, under foundations / ground floor slab ( grade slab ) , etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors, etc., complete as per drawings, specifications and as per the directions of engineer in charge. , providing, mixing and laying of pcc 1:4:8 nominal mix using 20 mm and downgraded coarse aggregate and using opc ( 53 grade ) for any thickness for all depths below raft, pile cap, etc., including shuttering, tamping, ramming, vibrating, curing, etc., all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete, as per drawings, specifications and as directed by engineer in charge. , providing, mixing and laying in position reinforced cement concrete ( rcc ) of grade m35 with 20mm and down graded coarse aggregates and minimum cement content of 400kg / cu.m as per is 456:2000 using 53 grade ordinary portland cement in sub structure for all depths upto 450mm from ground level along with cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash, etc. including single pour concreting as specified in drawing, ( excluding the cost of reinforcement and shuttering ) , etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete ( rcc ) of grade m30 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg / cu.m; as per is 456:2000 using 53 grade ordinary portland cement in super structure for all heights above 450mm from ground level ( upto and inclusive of 20m ) including cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. ( excluding the cost of reinforcement, shuttering ) , etc. all complete as specified, and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete ( rcc ) of grade m20 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg / cu.m; as per is 456:2000 using 53 grade ordinary portland cement for grade slab including tamping, screening ( if & as specified in drgs ) to achieve a smooth surface and proper slope without additional finish along with cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chafering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc. ( excluding the cost of reinforcement and shuttering ) , etc. all complete as specified and directed by engineer in charge. , providing and fixing formwork in sub structure for all depths and height upto 450mm above ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents of approved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , providing and fixing formwork in super structures for all heights above 450mm from ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents ofapproved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500d for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge ( swg ) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in cement mortar 1:4 ( 1 cement:4 m sand ) for all heights including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam / slab, embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in sub structure with bricks of class 5.0 in cement mortar 1:6 ( 1 cement:6 m sand ) for all depths including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, finishing the joints flush below ground level, curing, excluding plaster, etc. all complete as per specifications, and as directed by engineer in charge. , providing 15mm thick cement plaster in cement mortar 1:4 ( 1 cement:4 m sand ) on brickmasonry, pcc / rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curingincluding mouldings and providing grooves in plaster, bands, mouldings, etc. as specified for all depths and heights including labour charges, tools and tackles, material costs, etc. as per specifications and as directed by the engineer in charge. , providing 20mm thick cement plaster in 2 coats, 1st coat of 12 mm thick in cement mortar 1:4 ( 1 cement : 4 m sand ) & 2nd coat of 8 mm thick in cement mortar 1:4 ( 1 cement : 4 m sand ) plain cement plaster outside / inside the building / boundary wall finished to a smooth finish including providing grooves at junctions of two dis similar materials all complete as directed by eic. , providing 6mm thick cement plaster in cement mortar 1:3 ( 1cement:3 m sand by volume ) on roof ceilings, concrete surfaces including preparation of base, cleaning, chipping, packing of electrical works, scaffolding, finishing, curing, etc. for all heights complete with all labour charges, material costs, tools and tackles, etc. as per specifications and as directed by the engineer in charge. , providing & applying interior paint one coat of emulsion primer & filling services, if any with putty & applying two coats of acrylic distemper paint of asian / approved equivalent make, as per the manufacturer’s specifications including necessary scaffolding, brushing, cleaning & surface preparation with plaster of paris punning, etc. complete as per specifications, drawings and as directed by engineer in charge. , providing and applying textured granular type wall coating of bakelitehylam ltd. or approved equivalent, consisting of twin pack fine gradesilica granules / dry flakes made of special grade of china clay / granite type flakes of heritage or equivalent in approved shade and texture;mixed in situ with 100% acrylic polymer bonding agent; applied overplastered surfaces; the granules / flakes etc., bonding material, mixing, method of application, surface preparation etc. all shall be as per manufacturers recommendations and specifications all complete as directed by engineer in charge. , providing and applying three coats of approved white wash ( comprising of fat lime, water, gum with hot water and sodium chloride with hot water ) in interior surfaces as per the specifications including necessary scaffolding and surface preparation, etc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of premium acrylic emulsion exterior paint of required shade and including surface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty, necessary scaffolding, etc., all complete as per specifications and directions of engineer in charge. , providing and laying water proofing membrane to roof of atacticpoly propylrnr ( app ) with non woven polyster reinforcement having thin poly ethylene foil of approved quality inculding cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturers specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. ( the thickness of atactic poly propylene ( app ) membrane to be considered as 4.0mm ) , providing and fixing tray type aluminium plank false ceiling consisting of 254 / 305mm x 1264mm or 600mm x 600mm size aluminium planks ( profiled for positive engagement into clip in profiles and demounting of individual planks ) manufactured out of 0.7mm thk. aluminium alloy 3105 / 3005 / 5052 ( as per astm 209m ) with stove enamelled ( coil coated ) finish in approved colour and suspension system consisting of 0.5mm thk. 40mm x 20mm galvnized steel clip in main runner profiles ( @1264m or 600mm as per plank size ) supported by and including 0.5mm thk. 25mm x 16mm gi suspension angle, 1mm thk. 25mm x 34mm x 76mm crca zinc plate steel ceiling brackets ( @ max. 1264mm c / c or 600mm as per profile ) fixed to roof slab / beam, 0.5mm thk. 40mm wide, 105mm high g.i> hold on clamps slotted for level adjustment, perimeter angles including providing slit openings for fixing supply / return air grill, lighting fixtures, ac ducts etc. all complete. , providing and fixing pressed steel door and window frames ofsize ( assorted size out of ) overall 125mm x 60mm section, of required profile confirming to is: 4351, made of 16 swg pressed steel including / consisting of: i ) 3 mm thick ms flat spacers welded to frame @500 mm c / c and at hold fast locations. ( ii ) filling the hollow frame section with concrete. ( iii ) ms angle ( 20mm x 20mm x 3mm ) horizontal tie member below floor furnish ( iv ) ms hold fasts ( 200mm x 25mm x 6mm ) welded to spacers. ( v ) fixing to masonery ( by grouting the holdfasts with m 15 grade concrete in minimum 250mm x 100mm x 100mm sized hole ) / fixing to rcc ( bu minimum 100mm long, 12mm dia metallic counter sunk anchor fasteners ) vi ) ms pad plates ( 40mm x 150mm x 3mm ) & gi mortar gaurd welded to frame at hinge and other hardware locations. vii ) metering of joints between horizontal and vertical members, grinding and smoothening of welding, cleaning of frame surface, finishing ( synthetic enamel painting / electrostatic powder coating / polyurethane ( pu ) coating ) , making true alignements and surface etc. all complete. note: 1 ) cumulative length of all horizontal and vertical frame members shall be measured for payment. frames painted with polyurethane ( pu ) paint coating over epoxy primer. , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40mm overall thickness; and consisting of / including; ( i ) 3 mm thick ms flat all along perimeter ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @ 600 c / c maximum ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces etc. all complete. notes : only the net shutter ( s ) area shall be measured for payment. single shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16mm dia 250mm long aldrop on both sides of shutter. ( iii ) spring loaded heavy duty door stopper ( iv ) ss 304 grade 19mm dia.200 mm long handle on both side of shutter. ( v ) 10mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40mm overall thickness; and consisting of / including; ( i ) 3 mm thick ms flat all along perimeter ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @ 600 c / c maximum ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces etc. all complete. notes : only the net shutter ( s ) area shall be measured for payment. double shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16mm dia 250mm long aldrop on both sides of shutter. ( iii ) spring loaded heavy duty door stopper ( iv ) ss 304 grade 19mm dia.200 mm long handle on both side of shutter. ( v ) 10mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . , providing and fixing in position plastic doors ( with door frames ) , of uv stabilized compounds of pvc ( sintex or approved equivalent ) , consisting of 53 x 60mm l shaped door frame ( blr53 of sintex or equivalent ) , 33 x 47mm shutter frame ( dwuf 306 of sintex or equivalent ) , 30mm thick in fill panel slats, complete as per manufacturers specifications and recommendations, including all fittings, fasteners, fixtures, sealing periphery with polymeric sealant etc all complete. , providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded build up standard tubular sections / appropriate z sections and other sections of approved make confirming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for galzing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for seperately ) ; for shutters of doors, windows & ventilators made from powder coated aluminium ( minimum thickness of powder coating 50 micron ) including providing and fixing hinges / pivots and making provision for fixing of fittings whereever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) , providing and fixing toughened glass panes of 6.0 mm thickness in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge. ( cost of aluminium snap beading shall be paid in basic item ) , supplying, transporting, storing, fabricating and fixing in position ms steel inserts ( with lugs ) as shown in drawing including fabrication to any shape made out of flats, plates, rolled sections, sleeves, pipes etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both plain, reinforced cement concrete members inclusive of adjusting shittering & reinforcement / any other fixture, welding where ever necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts, & painting with one shop coat of inorganic zinc silicate primer ( 30 micron dft ) and finishing with two coats of anti corrosive paint ( 20 micron dft each coat ) brand and colour, etc complete as per drawing, specification and direction of engineer in charge. , providing, straightening, fabricating curb angle as per drawing including hold fasts ( ms round or flat ) welded to angles and fixing, painting with one coat of anti corrosive primer complete as per drawings and specifications. , supplying, assembling and installing 1000mm high stin finish stainless steel ( ss 304 grade ) tubular railing of approved design in staircase, ramps, around floor cutouts etc. consisting of :1.50mm dia ss pipe top handrail 2. 32mm dia ss pipe balusters ( at every third step for staircase, @ maximum 1200mm c / c for ramp, floor cutouts ) 3. 3 nos minimum 18mm dia ss pipe intermediate handrails. including: 1. fixing balusters to floor with 4 nos bolts and 8mm thick, 100mm dia ss base plate & ss cap / collar. 2. fixing top hadrail to the balusters with 12mm dia plate. 3. fixing intermediate handrails to the balusters with 12mm dia ss bar connector. 4. all endcaps, decorative caps over balusters, necessary bending, welding, polishing of all weld joints ( lenght of top handrail shall be measured for payment ) . , construction of brick masonery ( brick class 5 ) inspection chambers / manholes of 750mm x 750mm internal size 1000mm deep ( max. ) in cement mortar 1:4 ( 1 cement : 4 sand ) with ci frame and cover 500mm clear dia, ( circular medium duty of grade md 10 ) confirming to is:1726 fixedon rcc slab of m 30 grade, necessary excavation, supplying, fixing 4 nos. 16mm dia m.s. rungs, m 20 grade foundation concrete 1:3 cement mortar ( 1 cement : 3 sand ) plastering of 13mm average thickness for inside & 16mm avg thicness for outside exposed surfaces, backfilling, disposal of surplus earth upto a lead of 100m, benching with m 20 grade cement concrete and rendering smooth with a neat coat of cement slurry, painting the c.i. frame and cover with two coats chlorinated rubber zinc phosphate primer @ 40 dft per coat and finish painting consists of two coats of chlorinated rubber paint @ 40 dft per coat etc. all complete as per drawings, specifications and directions of engineer in charge. , providing and laying upto 600 x 600 mm size coloured glazed ceramic tiles for wall / dado, of approved make & shade including 20mm thick cement bedding c.m. 1:3, pvc beading with matching colour, pointing and finishing exposed joints with white cement / matching colour pigment, etc., including cleaning the finsihed surface with wax polishing complete with material costs, tools and tackles, labour charges as per specifications and as directed by engineer in charge. , providing and laying of permium quality antiskid ceramic floor tiles ( size of all tiles upto 1200 x 1200 ) of approved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement pase / grout mixed with colour pigments matching the shade of tiles, with material costs, tools and tackles, labour charges etc. as per specifications, standards and instructions of engineer in charge. , providing and laying vitrified floor tiles of size upto 1200mm x 1200mm of kajaria / jhonson / somany / orient bell or approved make laid on 20mm thick cement mortar 1:4 ( 1 cement:4 m sand ) including a coating of adhesive as per manufacturers specifications, flush pointing of joints of tiles with cement paste, grouting with white cement and pigment with colour matching the shades of tiles including skirting, finishing, curing, material costs, labour charges, tools and tackles etc. all complete as directed by engineer in charge. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases, etc. using non shrink grout of approved make equivalent including supply of material, roughening surface, cleaning with compressed air / water jets, ramming, curing, labour charges, etc. all complete as directed by engineer in charge. , supplying, transporting, fabricating, erecting and fixing in position as per the specifications, electroforced hot dip galvanised gratings ( gloating weight shall be 305gm / sqm as per is 4759 ) of the approved designed and pattern and erecting & fixing of fabricated steel work on operating floors, platforms, stair landings & treads, drain cover etc., at various levels includingsupply ofall gi fixtures like edge plates for treads, clips, studs, bolts, welding if required and nosing for the treads and etc., complete as per drawings specifications & as directed by engineer in charge , demolishing brick masonry in cement mortar ( taking all necessary safety precautions ) for all depths and heights below and above plinth level including demolition of existing watch tower structural members at all heights, supply of all labours, tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing rcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depth and height below and above plinth level including demolishing of existing foundation upto bottom of pile cap , demolition of existing watch tower structiral members at allheights, supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing pcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depths and heights below and above plinth levelincluding pcc below existing pile cap, including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , providing, hoisting and fixing in position rcc precast elements with reinforced cement concrete grade 1:1.5:3 ( 1 cement:1.5 m sand: 3 graded stone aggregate with opc 53 grade and 20mm & down size graded crushed stone aggregates ) for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks, levelling, aligning and fixing / laying in position using crane, breaking brickwork and / or concrete surfaces and making good the same, etc. all complete ( excluding cost of reinforcement ) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying structural steel conforming to is:2062 grade a, ( yield strength 250.0 n / mm2 ) transporting, storage, straightening, cleaning, fabricating welded / bolted structural steel work in columns, beams, trusses, purlins, platforms, ladders, monorails, staircases, supports, strengthening of steel members, etc. at all locations / levels up to and inclusive of 40.0 m height above hpp / fgl, including supply of bolts, supply of shim plates & approved welding electrodes, including all built up sections / compound sections made out of rolled sectionsand / or plates / bent plates in all types of structural frameworks, floor beams , stairs, or any other structural items or accessories to support equipments, piping , galleries, towers , masts etc, making templates, welding, bolting, erection bolting, splicing, etc. as per specifications and drawing and as directed by the owner / consultant. cutting to required size, straightening / bending if required, edge preparation, cleaing, scrapping and welding, preheating, finishing edges by grinding, fixing in line ans level, including preparing the surface for painting, surface cleaing, wire brushing, removal of mill scale, dust, rust, oil or grease, etc., complete along with providing paint system as follows: ( a ) applying inorganinc zinc silicate coat 50micron dft; ( b ) one coat of epoxy primer paint 50 micron dft each; ( c ) two coat of anti rust epoxy top coat paint 50micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after gritblast cleaing in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , dismantling / modification ofbolted and / or welded structural steel works already erected by others with all cranes and necessary machineries. at all locations and levels upto & inclusive of 50m above hpp / fgl, including all builtup sections / scaffoldingpipes / compound sections made out of rolled sections and / or plates / bent plates in all types of structural frameworks, floor beams, stairs or anyother structural items or accessories to support equipments, piping, conveyor galleries, towers, masts etc., providing temporary staging & bracing and removal of the same after erection and gas cutting, unwelding & bolt removing including supply of all tools & tackles, consumables, necessary scaffolding etc., providing temporary staging & bracing and removal of the same after erection and gas cutting, un welding & bolt removing including supply of all tools and tackles, consumables, necessary scaffolding etc., providing temporary bracings as required, cutting ( by flame or saw ) gusselt plates, bolts, nuts, welding etc., including necessary cranes, skilled & unskilled manpower required for the completing the work. transporting and stacking of all the serviceable materials to designated place and transporting to scrap yard within the refinery premises, all complete at all heights, as specified and directed by engineer in charge , providing and placing / spreading 500 microns thick hdpe sheet / film including laps as per drawing & as directed by engineer in charge. , providing & fixing in position bitumen impregnatedboard 12 mm thk. of approved make premoulded bituminous expansion / contraction / isolation joint filler boards conforming to is:1838 p1 / 1983 in joints including expansion / contraction joints, application of primer as directed by engineer in charge. , same as item no.440 above, but for 25mm thick board. , providing pockets for foundation bolts as per drawings including providing and removing of necessary formwork, etc. complete as per specifications and as directed by owner / consultant. ( for 100 mm x 100 mm to 300mm x 300 size in plan ) and upto 300mm depth , same as item no.460, but for 300mm to 600mm , same as item no.460, but for 600mm and above , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty mechanical anchor fasteners, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge. , same as item 490 above, but for 20mm dia , same as item 490 above, but for 24mm dia , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty chemical anchor fasteners, packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge. , same as item 520 above, but for 16mm dia , same as item 520 above, but for 20mm dia , supply and installation of cylindrical triple layer white virgin plastic storage tank of capacity 1000 litres of sintex or approved equivalent on ground floor roof with lid and making necessary cutout / holes for inlet, outlet and overflow pipes, necessary connections and sealing all joints properly, all complete. including, fixing, transportation to work site all complete as per drawings and directions of engineer in charge. , providing and fixing in position oval shaped coloured glazed vitreous china wash basin 550 x 400 mm of approved equivalent make including c.i. brackets fixed on walls, chromium plated couplings rubber plug with chromium plated chain and chromium plated tap with brass unions, brass c.p. bottle trap with cleaning nut and 32mm dia g.i.waste pipe ( from floor level to nahani trap ) complete with all necessary fittings and put into proper working order as per the specifications, drawings & as directed by engineer in charge. , providing and fixing white glazed earthern ware half stall urinal of parry ware niagara or approved equivalent, including parryware brandor approved equivalent cp urinal push angle valve, cp brass spreader with 32 mm dia pvc pipe, tee, distribution pipe, brackets etc. making inlet & outlet connections fixing with cp brass screws, finishing, etc. all complete as directed by engineer in chagre , providing and fixing in position chromium plated brass liquid soap dispenser of approved quality and design fixed with chromium plated brass screws finished complete as per the drawings, specifications and as directed by engineer in charge. , providing & fixing wall mounted coloured designer type european type wc of approved equivalent with seat cover, p or s traps and low level earthen ware cistern of 10 litres capacity of approved make with chromium plated stop cock & ball cock fittings etc. complete as per drawings, specifications and as directed by engineer in charge. , providing and fixing 150 mm dia. rigid pvc pipes as rain water pipes, weep hole pipes etc. with ms holder clamps including fixing / embedding into masonry / concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg / sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing 15mm dia. nominal bore upvc pipes ( sch 80 ) of ashirvad or approved equivalent including upvc fittings viz. elbows, reducers, couplers, end caps, tees, union, tank nipple, female adapter, male adapter, bends and providing pvc cement and joining with the pipes complete for both open and concealed works including providing ss clamps for fixing in open works and chipping the wall and making good the same after completion of concealed works etc. all complete as per directions of engineer in charge. , same as sl.no. 610 above, but for 20mm dia. nominal bore pipes , same as sl.no. 610 above, but for 25mm dia. nominal bore pipes , same as sl.no. 610 above, but for 40mm dia. nominal bore pipes , same as sl.no. 610 above, but for 80mm dia. nominal bore pipes , same as sl.no. 610 above, but for 100mm dia. nominal bore pipes , supplying and fixing m.s. nozzles with puddle flanges upto 200mm diameter in position as directed with necessary breaking of concrete / brickwork in slabs, beams, walls grouting with non shrinking grout ( if required ) and making the surface good, curing, painting with one coat of anti corrosive primer rtc. complete ( grouting to be paid separately ) . , same as item no. 670, but for 200mm dia to 500mm ms nozzle with puddle flange. , providing and fixing in position under deck insulation consisting of rigid polyisocyanurate foam ( pir ) slabs of size 1000 x 500mm and thickness of 30mm ( covered on one side with glass fibre tissue / aluminium foil having 50mm overlap ) confirming to is:12436 having density not less than 32 kg. / cum., thermal conductivity ( k value ) not more than 0.023 w / mk measured at 10 deg. c; classified as class i for surface spread of flame as per bs 476, part 7; fixed to r.c.c. slab by hot blow grade bitumen of 85 / 25 grade or cold adhesive cprx applied over a coat of bituminous primer @ 0.5 litres / sq.m. applied to bare r.c.c. surface and to the two surface of each pir panel and pressed in position ( while the bitumen is still tacky ) with the help of g.i. screws ( no. 8 x 75mm long ) fixed into rawl plugs ( holes in r.c.c. for the raw plugs shall be drilled prior to applying coat of bituminous primer ) of size 8 x 25mm inserted ( 5 nos. for each slab one each at 4 corners and one at center ) and g.i washers 25mm dia; including covering the overlaps with approved quality sealing compound ( mas 94 or equivalent ) ; chicken wire mesh 24g x 19mm shall then be fixed to g.i screws and tightened with lacing wire; including preparation of surface consisting of cleaning r.c.c surface of all dust, dirt and loose particles by wire brushing; etc. all complete as per approved manufacturers standard specifications and recommendations. , cut or form a hole, square or circular through reinforced concrete floor or wall exceeding 150 mm but not exceeding 500 mm thick & make good complete as directed by owner / consultant, for area of cutting in between 65 and upto 250 sq.cm, all complete as directed by eic. ( for cutouts, below 65 sq.cm surface area, no extra payment will be made ) , same as item no.700, but for area of cutting in between 260 up to 500 sq.cm. , supplying and applying two coats of coal tar epoxy paint of approved make as per manufactures specifications with minimum of volume solids as 65% coal tar content as 40% pigment content as 22% and dft per coat as 100 microns, on all exposed surfaces of rcc in substructure eg. foundation, footings, rafts, pile caps, beams, slabs, pedastals, trenches, manholes, catchpits, drains, rcc pits, pipe sleepers, equipment / machine foundations etc. all complete for all depths below ground level etc. including all labour, tools and tackles complete as directed by eic. , demolition of existing stores ( 02 nos. ) near wagon loading silos of size approx. 30.1mx10mx6m and 17.78mx7.75mx6m including dismantling of flooring, fixtures, doors, windows, partitions, rolling shutter etc., asbestos sheeting, truss, purlin, structural steel items etc. all complete as directed by engineer in charge. this includes demolishing foundation upto bottom of pile cap and pcc layer underneath if resting on pile else complete foundation including raft and underlying layersis to be demolished in case of open foundation.all unserviceable material should be disposed atvaikkadu area outside the refinery premises up to a lead of 7km as per specifications and as directed by the engineer in charge .all serviceable materials shall be the property of contractor. unserviceable material includes plain cement concrete, reinforced cement concrete excluding reinforcement bars, fire proofing materials, insulations, floor finishes and water proofing layers, bricks, stones, rubbish, vitreous ( ceramic ) sanitary items like washbasin, urinals, water closets and plumbing fittingsetc.serviceable materials are reinforcement steel, structural steel , roof / side cladding sheets, chequered plate, gratings, hand railing, doors, wooden / steel / aluminium windows & ventilators shutters, frames steel / aluminium grills, partitions, steels gates, rolling shutters, etc. as decided by the engineer in charge. , supplyof unskilled labour to carry out petty works not assessable for measurements / minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits and hand tools. , supply of jcb on hire basis on all working days from monday to saturday on 8 hrs. shift including driver, assitant / fuel / oil / lubricants / all consumables etc. complete. the quoted rate should include mobilization, operator crews / driver / assistant cost, labour, tools, tackles etc., as directed by the engineer in charge. , supply of poclain pc 200 on hire basis including fuel / oil / lubricants for excavating the existing compacted earth, levelling to required slopes and dumping at designated places within the site premises. the quoted rate should include mobilization, operator crews / driver cost, loading, transporting, unloading, labour, tools, tackles etc. complete as directed by engineer in charge , providing necessary barricading works with 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3m, embedding the same in firm ground with necessary foundation works, etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works. the same will be the property of contractor....

Chennai Petroleum Corporation Limited - Tamil Nadu

31636740 civil works for construction of silo and other associated civil works for coke handling system in manali refinery of cpcl civil works for construction of silo and other associated civil works for coke handling system in manali refinery of cpcl , supplying, transportation, installing, dismantling and removing of interlocking type temporary steel sheet piles with crane / jcb / poclain / vibro hammer / pile driving machinery of adequate capacity and other ancillary equipment, including driving and joining the sheet piles as per specification up to levels indicated in the drawings & specifications. installed sheet piles are temporary and shall retain the earth, provide excavation support for a depth of 5m from ground level and protection against water seepage & sliding of earth during construction activities, including supply of all materials, steel members, welding, strutting, tie members supporting, labour, plant & machineries, etc. all complete as directed by engineer in charge. ( notes: ( i ) method of measurement for payment will be the actual horizontal limit of temporary sheet piling installed and accepted, and the vertical limit as measured from the bottom of the exposed face of the sheeting to the top of the retained earth behind the sheeting. ( ii ) the steel sheet piles shall be supplied by the contractor and shall remain the property of the contractor ) . , providing necessary barricading works with 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3m, embedding the same in firm ground with necessary foundation works, etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works. the same will be the property of contractor. , earthwork excavation in all types of soil depth up to 1.5 m, includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means ( hydraulic excavators ) / manually includingclearing away of vegetations, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated / sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed includingshoring and strutting and providing temporary supports to existing service lines like water pipes, product pipes, sewage pipes, electric overhead and underground cables, cable trenches, etc. all complete as per the specifications and directions of engineer in charge. , same as item no. 30 above, but for depth beyond 1.50 m and upto 3.0 m. , same as item no. 30 above, but for depth beyond 3.0 m and upto 4.80 m. , transporting & disposing the surplus earthfrom construction area to vaikkadu area up to a lead of 7km including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas ( viz., from where the earth is transported and where it is deposited ) to required levels and slopes complete with all lifts as directed by engineer in charge. ( note: if measured by stacks, 30% voids will be deducted. ) , supplying and filling approved m sand of specified quality under raft, foundation, etc. for all depths including the cost of sand, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layers not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and / or other equipment to specified level all complete as per specifications and directions of engineer in charge. , backfilling after execution of work to proper grade and level with selected materials from available excavated soil stacked in soil heaps within a lead of 100 m, including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths & heights in layers of thickness not exceeding 150 mm watering, rolling and ramming by manual methods / mechanical compactors, dressing, trimming, etc., in foundations, plinths, trenches, pits, etc. including all labours, tools & tackles, etc. all complete as per the specifications and directions of engineer in charge. , providing & laying dry rubble soling ( hard core ) with 20 to 40 mm size metal, under foundations / ground floor slab ( grade slab ) , etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors, etc., complete as per drawings, specifications and as per the directions of engineer in charge. , providing, mixing and laying of pcc 1:4:8 nominal mix using 40 mm and downgraded coarse aggregate and using opc ( 53 grade ) for any thickness for all depths below raft, pile cap, etc., including shuttering, tamping, ramming, vibrating, curing, etc., all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete, as per drawings, specifications and as directed by engineer in charge. , providing, mixing and laying in position reinforced cement concrete ( rcc ) of grade m35 with 20mm and down graded coarse aggregates and minimum cement content of 400kg / cu.m as per is 456:2000 using 53 grade ordinary portland cement in sub structure for all depths upto 450mm from ground level along with cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash, etc. including single pour concreting as specified in drawing, ( excluding the cost of reinforcement and shuttering ) , etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete ( rcc ) of grade m30 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg / cu.m; as per is 456:2000 using 53 grade ordinary portland cement in super structure for all heights above 450mm from ground level ( upto and inclusive of 20m ) including cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. ( excluding the cost of reinforcement, shuttering ) , etc. all complete as specified, and directed by engineer in charge. , same as item no. 120 above, but for height above 20m upto 50m including silo wall concreting , providing and laying reinforced self finished / broomer finish concrete of grade m35 with 40 mm & down size graded stone aggregates and mixing by mechanical mixers for roadwork / pavement in alternate bays, including tamping, compacting by internal and surface vibrators, providing smooth shuttering, providing camber to the surface, providing joints, curing, tarring the sides of slab with hot bitumen, etc. also including applying cement slurry ( 2.75 kg / m2 ) prior to placing concrete, complete as per the drawings and specifications and as directed by the engineer in charge. ( reinforcement shall be paid separately. ) , providing and fixing formwork in sub structure for all depths and height upto 450mm above ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents of approved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , providing and fixing formwork in sub structure for curved shuttering in foundations in all types for columns, beams, slabs, walls, etc. of buildings for all depths below and upto & inclusive of plinth level, including strutting, bracing, propping, etc., keeping the same in position during concreting and removal of the same after specified period, etc. for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or any other fixture, etc. all complete and as specified and directed. , providing and fixing formwork in super structures for all heights above 450mm from ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents ofapproved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. for all works above 450mm and upto 20 m , same as item no. 170 above, but for height above 20 m and upto 50 m , providing and fixing formwork in superstructures for curved shuttering in all types for columns, beams, slabs, walls, etc. of buildings for all heights above plinth level, including strutting, bracing, propping, etc., keeping the same in position during concreting and removal of the same after specified period, etc. for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or any other fixture, etc. all complete and as specified and directed. , same as item no. 190 above, but for height above 20m upto 50m , supplying, installing, dismantling and removing slip form shuttering arrangement for construction of rcc silo shell for all elevations from 20 m up to 50 m above gl as per drawings and specifications at all levels, using steel / plywood / wood shuttering. the quoted rate includes providing working platform inside & outside, structural beam / column for erecting slip form arrangements, scaffoldings, jack system, motors, metal ropes, safety nets as per the requirement, winch & lifting arrangement separately for materials and labour movement, all tool & tackles, machineries and materials, etc., all complete as per direction of engineer in charge. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500d for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge ( swg ) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying half brick masonry with bricks of class 5.0 in cement mortar 1:4 ( 1 cement : 4m sand ) for all depths and heights including cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing and laying brick masonry in super structure with bricks of class 5.0 in cement mortar 1:4 ( 1 cement:4 m sand ) for all heights including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam / slab, embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in sub structure with bricks of class 5.0 in cement mortar 1:6 ( 1 cement: 6 m sand ) for all depths including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, finishing the joints flush below ground level, curing, excluding plaster, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in using cement mortar 1:6 ( 1 cement:6 m sand ) for all heights including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam / slab, embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing 15mm thick cement plaster in cement mortar 1:4 ( 1 cement:4 m sand ) on brickmasonry, pcc / rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curingincluding mouldings and providing grooves in plaster, bands, mouldings, etc. as specified for all depths and heights including labour charges, tools and tackles, material costs, etc. as per specifications and as directed by the engineer in charge. , providing 12mm thick cement plaster in cement mortar 1:4 ( 1 cement:4 m sand ) on brickmasonry, pcc / rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curing including mouldings and providing grooves in plaster, bands, mouldings, etc. as specified for all depths and heights including labour charges, tools and tackles, material costs, etc. as per specifications and as directed by the engineer in charge. , providing 20 mm thick cement plaster in 2 coats, 1st coat of 12 mm thick in cement mortar 1:4 ( 1 cement:4 m sand ) & 2nd coat of 8 mm thick in cement mortar 1:4 ( 1 cement:4 m sand ) plain cement plaster outside / inside the building / boundary wall finished to a smooth finish including providing grooves at junctions of two dissimilar materials all complete as directed by eic. , providing 6mm thick cement plaster in cement mortar 1:3 ( 1cement:3 m sand by volume ) on roof ceilings, concrete surfaces including preparation of base, cleaning, chipping, packing of electrical works, scaffolding, finishing, curing, etc. for all heights complete with all labour charges, material costs, tools and tackles, etc. as per specifications and as directed by the engineer in charge. , providing & applying interior paint one coat of emulsion primer & filling services, if any with putty & applying two coats of acrylic distemper paint of asian / approved equivalent make, as per the manufacturer’s specifications including necessary scaffolding, brushing, cleaning & surface preparation with plaster of paris punning, etc. complete as per specifications, drawings and as directed by engineer in charge. , providing and applying three coats of approved white wash ( comprising of fat lime, water, gum with hot water and sodium chloride with hot water ) in interior surfaces as per the specifications including necessary scaffolding and surface preparation, etc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of premium acrylic emulsion exterior paint of required shade and including surface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty, necessary scaffolding, etc., all complete as per specifications and directions of engineer in charge. , providing & laying water proofing membrane to roof of atactic polypropylene ( app ) with non woven polyester reinforcement having thin polyethylene foil of approved quality including cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturer’s specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. ( the thickness of atactic polypropylene ( app ) membrane to be considered as 4.0 mm. ) , providing and fixing tray type aluminium plank false ceiling consisting of 254 / 305mm x 1264mm or 600mm x 600mm size aluminium planks ( profiled for positive engagement into clip in profiles and demounting of individual planks ) manufactured out of 0.7mm thk. aluminium alloy 3105 / 3005 / 5052 ( as per astm 209m ) with stove enamelled ( coil coated ) finish in approved colour and suspension system consisting of 0.5mm thk.40mm x 20mm galvanised steel clip in main runner profiles ( @ 1264mm or 600mm as per plank size ) supported by and including 0.5mm thk. 25mm x 16mm gi suspension angle, 1mm thk. 25mm x 34mm x 76mm crca zinc plated steel ceiling brackets ( @ max.1264mm c / c or 600mm as per profile ) fixed to roof slab / beam, 0.5 mm thk. 40mm wide, 105mm high g.i. hold on clamps slotted for level adjustment, perimeter angles including providing slit openings for fixing supply / return air grill, lighting fixtures, ac ducts, etc. all complete. , providing & laying 15mm thick tile acid resistant tiles ( vitrified ) to floors of approved make bedding & joints filled with appropriate acid proof cement. all work complete as per manufacturer’s specifications, drawing & as directed by engineer in charge. , providing & laying acid resistant tiles ( vitrified ) to 10 to 12 mm thick for walls of approved make with applying 2 coats ( to the base concrete ) of mixture of general purpose polymer ( bonding agent ) mixed with opc cement, sprinkling silica to make surface rough. bedding mortar of 8 to 10 mm thickness in 1:3 ratio with 5 % general purpose polymer added to cement. joints of min. width 5 to 8 mm raked, cleaned & filled with appropriate acid proof cement. all work complete as per manufacturer’s specifications, drawing & as directed by engineer in charge. , providing and fixing 2 hours fire rated single shutter steel doors consisting of steel door frame, shutter, vision panel, insulation and hardware such as hinges panic bar, locks / trims for panic bar, door closer, door stopper, consealed flush bolt, etc. including fixing with masonry, partition, etc. all complete as per specificaitons and approved manufacturers details. , providing and fixing pressed steel door and window frames of size ( assorted size out of ) overall 125mm x60mm section, of required profile conforming to is: 4351, made of 16 swg pressed steel including / consisting of: ( i ) 3 mm thick ms flat spacers welded to frame @ 500mmc / c and at holdfast locations. ( ii ) filling the hollow frame section with concrete. ( iii ) ms angle ( 20mmx20mmx3mm ) horizontal tie member below floor finish. ( iv ) ms holdfasts ( 200mmx25mmx6mm ) welded to spacers. ( v ) fixing to masonry ( by grouting the holdfasts with m 15grade concrete in minimum 250mm x 100mm x 100mmsized hole ) / fixing to rcc ( by minimum 100mm long, 12 mm dia metallic counter sunk anchor fasteners ) ( vi ) ms pad plates ( 40mm x150mm x 3mm ) & gi mortar guard welded to frame at hinge and other hardware locations. ( vii ) metering of joints between horizontal and vertical members, grinding and smoothening of welding, cleaning of frame surface, finishing ( synthetic enamel painting / electrostatic powder coating / polyurethane ( pu ) coating ) , making true alignments and surfaces, etc. all complete. notes: ( 1 ) cumulative length of all horizontal and vertical frame members shall be measured for payment. frames painted with polyurethane ( pu ) paint coating over epoxy primer. , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40 mm overall thickness; and consisting of / including: ( i ) 3 mm thick ms flat all along perimeter. ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap. ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c. ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware, etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @600 c / c maximum. ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces, etc. all complete. notes: only the net shutter ( s ) area shall be measured for payment. single shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16 mm dia 250mm long aldrop on both sides of shutter. ( iii ) spring loaded heavy duty door stopper. ( iv ) ss 304 grade 19 mm dia.200 mm long handle on both side of shutter. ( v ) 10 mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40 mm overall thickness; and consisting of / including: ( i ) 3 mm thick ms flat all along perimeter. ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap. ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c. ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware, etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @600 c / c maximum. ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces, etc. all complete. notes: only the net shutter ( s ) area shall be measured for payment. double shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16 mm dia 300mm long aldrop on bothsides of shutter. ( iii ) spring loaded heavy duty door stopper. ( iv ) ss 304 grade 19 mm dia.200 mm long handle on both side of shutter. ( v ) 10 mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . ( vi ) 2mm thick 25mmx 25mm gi angles ( vertical ) welded to each shutter at the meeting point of double shutter. , providing and fixing in position plastic doors ( with door frames ) , of uv stabilized compounds of pvc ( sintex or approved equivalent ) , consisting of 53x 60mm l shaped door frame ( blr53 of sintex or equivalent ) , 33x47mm shutter frame ( dwuf 306 of sintex or equivalent ) , 30mm thick infill panel slats, complete as per manufacturers specifications and recommendations, including all fittings, fasteners, fixtures, sealing periphery with polymeric sealant, etc. all complete. , providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket, etc. aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p.brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) ; for fixed portion of aluminium doors, windows, ventilators and partitions made from powder coated aluminium ( minimum thickness of powder coating 50 micron ) , providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket, etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p.brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) ; for shutters of doors, windows & ventilators made from powder coated aluminium ( minimum thickness of powder coating 50 micron ) including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) , providing and fixing 12 mm thick pre laminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ii, with decorative lamination on both sides, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws, etc. complete as per architectural drawings and directions of engineer in charge. , providing and fixing toughened glass panes of 6.0 mm thickness in aluminium door, window, ventilator shutters and partitions, etc. with epdm rubber / neoprene gasket, etc. complete as per the architectural drawings and the directions of engineer in charge. ( cost of aluminium snap beading shall be paid in basic item ) , supplying, transporting, storing, fabricating and fixing in position ms steel inserts ( with lugs ) as shown in drawing including fabrication to any shape made out of flats, plates, rolled sections, sleeves, pipes, etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both plain, reinforced cement concrete members inclusive of adjusting shuttering & reinforcement / any other fixture, welding wherever necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts, & painting with one shop coat of inorganic zinc silicate primer ( 30micron dft ) and finsihing with two coats of anti corrosive paint ( 20micron dft each coat ) on exposed surface only, of approved brand and colour, etc. complete as perdrawing, specification and direction of engineer in charge. , supplying, fabricating, fixing and installation in position at all levels and locations threaded m.s. anchor bolts of all diameters and nomenclature including nuts, washers, anchor plates, washer plates, closure plates, pipe sleeves, etc. in foundations, pedestals, etc. as directed including handling & transporting, straightening if required, turning from relevant size, m.s. rounds to required diameter, threading, welding, providing necessary templates and auxillary dummy structure, if any, necessary tying and welding, providing necessary templates and auxillary dummy structures, if any, necessary tying and welding with reinforcement bars, adjustment of shuttering & reinforcement / any other fixture, greasing exposed metal surfaces, covering bolts and packing the sleeves with jute cloth, etc. all complete as per drawing and specification and direction of engineer in charge. , same as item no.480 above, but for collecting from owner store, fixing and installation in position at all levels and locations ( excluding supply / fabrication which is in owner scope ) , etc. complete. , providing, straightening, fabricating curb angle as per drawing including holdfasts ( ms round or flat ) welded to angles and fixing, painting with one coat of anticorrosive primer complete as per drawings and specifications. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases, etc. using non shrink grout of approved make equivalent including supply of material, roughening surface, cleaning with compressed air / water jets, ramming, curing, labour charges, etc. all complete as directed by engineer in charge. , demolishing brick masonry in cement mortar ( taking all necessary safety precautions ) for all depths and heights below and above plinth level including supply of all labours, tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing rcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depth and height below and above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing pcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depths and heights below and above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , supply of unskilled labour to carry out petty works not assessable for measurements / minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits and hand tools. , same as item no.550 above, but for supply of skilled labour. , providing, hoisting and fixing in position rcc precast elements with reinforced cement concrete grade 1:1.5:3 ( 1 cement:1.5 m sand: 3 graded stone aggregate with opc 53 grade and 20mm & down size graded crushed stone aggregates ) for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks, levelling, aligning and fixing / laying in position using crane, breaking brickwork and / or concrete surfaces and making good the same, etc. all complete ( excluding cost of reinforcement ) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying and sealing expansion joints 25mm wide and 12mm deep at all locations and levels in concrete structures with approved two parts liquid polysulphide sealing compound as per is: 12118 including raking of joints, etc. all complete as shown, specified and directed by eic. , supplying and sealing expansion joints 50mm wide and 12mm deep at all locations and levels in concrete structures with approved two parts liquid polysulphide sealing compound as per is: 12118 including raking of joints, etc. all complete as shown, specified and directed by eic. , supplying structural steel conforming to is:2062 grade a, ( yield strength 250.0 n / mm2 ) transporting, storage, straightening, cleaning, fabricating welded / bolted structural steel work in columns, beams, trusses, purlins, platforms, ladders, monorails, staircases, supports, strengthening of steel members, etc. at site to line and level, including supply of bolts, supply of shim plates & approved welding electrodes, including making templates, welding, bolting, erection bolting, splicing, etc. as per specifications and drawing and as directed by the owner / consultant. cutting to required size, straightening / bending if required, edge preparation, cleaing, scrapping and welding, preheating, finishing edges by grinding, fixing in line ans level, including preparing the surface for painting, surface cleaing, wire brushing, removal of mill scale, dust, rust, oil or grease, etc., complete along with providing paint system as follows: ( a ) applying inorganinc zinc silicate coat 50micron dft; ( b ) one coat of epoxy primer paint 50 micron dft each; ( c ) two coat of anti rust epoxy top coat paint 50micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after gritblast cleaing in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , providing and placing / spreading 500 microns thick hdpe sheet / film including laps as per drawing & as directed by engineer in charge. , providing & fixing in position bitumen impregnatedboard 12 mm thk. of approved make premoulded bituminous expansion / contraction / isolation joint filler boards conforming to is:1838 p1 / 1983 in joints including expansion / contraction joints, application of primer as directed by engineer in charge. , same as item no.620 above, but for 25mm thick board. , providing pockets for foundation bolts as per drawings including providing and removing of necessary formwork, etc. complete as per specifications and as directed by owner / consultant. ( for 100 mm x 100 mm to 300 mm x 300 mm size in plan ) and upto 300 mm depth. , same as item no.640, but for depth from 300mm to 600mm. , same as item no.640, but for depth 600mm and above. , supplying, assembling and installing 1000 mm high satin finish stainless steel ( ss 304 grade ) tubular railing of approved design in staircases, ramps, around floor cutouts, etc. consisting of: ( 1 ) . 50mm dia ss pipe top handrail. ( 2 ) . 32 mm dia ss pipe balusters ( at every third step for staircase, @ maximum 1200mm c / c for ramp, floor cutouts ) . ( 3 ) . 3 nos. minimum 18mm dia ss pipe intermediate handrails, including: ( 1 ) . fixing balusters to floor with 4 nos. bolts änd 8mm thick, 100mm dia ss base plate & ss cap / collar. ( 2 ) . fixing top handrail to the balusters with 12mm dia ss bar connector & 6mm thick ss saddle plate. ( 3 ) . fixing intermediate handrails to the balusters with 12mm dia ss bar connector. ( 4 ) . all end caps, decorative caps over balustrades, necessary bending, welding, polishing of all welded joints ( length of top handrail shall be measured for payment ) . , supplying and fixing in position hydrophilic self swelling water stops as per manufacturers specifications in rcc structures at all locations including cutting, fixing and jointing, etc. all complete as shown, specified and directed by eic. , providing and fixing 150 mm dia. rigid pvcpipesas rain water pipes, weep hole pipes etc. with ms holder clamps including fixing / embedding into masonry / concrete, providing connections like shoes, vents, specials, bends, etc. fixing in perfect plumb, etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg / sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing 100 mm dia. rigid pvc pipes with pressure rating of 4 kg / sq.cm of approved brand including all fixtures as vent pipe for septic tank, machine welded, rubber ring joints using approved lubricant, making hole in the slaband restoring the same to the original condition including provision of cowl in the septic tank vent pipe, etc. complete as per specifications and directions of engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal bore brass bib cock including breaking walls and making good the same, inlet and outlet connections, etc. complete as directed by engineer in charge. , providing and fixing 15 mm dia. nominal bore upvcpipes ( sch 80 ) of ashirvad or approved equivalent including upvc fittings, viz., elbows, reducers, couplers, end caps, tees, union, tank nipple, female adapter, male adapter, bends and providing pvc cement and joining with the pipes complete for both open and concealed works including providing ss clamps for fixing in open works and chipping the wall and making good the same after completion of concealed works, etc. all complete as per directions of engineer in charge. , same as sl. no. 720 above, but for 20mm dia. nominal bore pipes. , same as sl. no. 720 above, but for 25mm dia. nominal bore pipes. , same as sl. no.720 above, but for 40mm dia. nominal bore pipes. , same as sl. no.720 above, but for 80mm dia. nominal bore pipes. , same as sl. no. 720 above, but for 100mm dia. nominal bore pipes. , providing and fixing in position stainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheet supported on m.s. brackets, supply, fixing of m.s.brackets, fasteners, sink cock ( quarter turn range ) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipe with heavy bottle trap of parryware or approved equivalent make, inlet pipe, drain pipe, rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls wherever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing, etc., all complete as directed by engineer in charge. , providing and laying reinforced np3 class ( medium duty ) rcc hume pipe of 300mm dia. with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1cement:2m sand ) for road crossing, etc. including cutting, lowering, laying in position, with proper level, slope, testing of joints, etc. as per specifications and directed by engineer in charge. , same as item no. 790 above, but for 600 mm dia. hume pipe , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty mechanical anchor fasteners, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as per manufacturers specification and directed by engineer in charge. , same as item no.810 above, but for 20mm dia. , same as item no.810 above, but for 24mm dia. , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty chemical anchor fasteners, packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge. , same as item no.840 above, but for 16mm dia. , same as item no.840 above, but for 20mm dia. , supplying and fixing m.s. nozzles with puddle flanges upto 200mm diameter in position as directed with necessary breaking of concrete / brickwork in slabs, beams, walls grouting with non shrinking grout ( if required ) and making the surface good, curing, painting with one coat of anti corrosive primer, etc. complete ( grouting to be paid separately ) . , same as item no.870, but for 200 mm dia to 500mm ms nozzle with puddle flange. , cut or form a hole by chipping, square or circular through reinforced concrete floor or wall for area in between 65 to 250 sq.cm, not exceeding 150mm thick and make good all complete as directed by eic. ( note: for cutouts, below 65 sq.cm surface area, no extra payment will be made ) , same as item no.890, but for area of cutting in between 260 up to 500 sq.cm. , cut or form a hole, square or circular through reinforced concrete floor or wall exceeding 150 mm but not exceeding 500 mm thick & make good complete as directed by owner / consultant, for area of cutting in between 65 and upto 250 sq.cm, all complete as directed by eic. ( for cutouts, below 65 sq.cm surface area, no extra payment will be made ) , same as item no.910, but for area of cutting in between 260 up to 500 sq.cm. , supplying of 150mm dia gi pipe ( h ) , fabricating, fit up, welding, laying, alligning, including shifting to location & gi painting to the welding portion, etc. complete as per drawing & specification & as per direction of the engineer in charge , same as item no.930, but for 100mm dia. , same as item no.930, but for 75mm dia. , providing, fabrication and fixing g.i. pipe inserts of 40mm dia with fixing arrangement on slab, platforms & silo walls, shown in drawing includingproviding necessary scaffolding, staging, cutting, straightening, if required, embedding in position on both plain, reinforced cement concrete members, fixing to structural steel inclusive of adjusting shuttering & reinforcement / any other fixture, welding where necessary, tying and holding to correct level, line and position, any auxiliary dummy structures to support the heavy inserts all complete as per drawing and specification and direction of engineer in charge. , same as item no.960, but for 25mm dia. , providing and applying two coats of cold applied heavy duty bituminous protective coating over one coat of primer to external faces of underground concrete structures after thorough cleaning of concrete, surface preparation, complete as per drawing and manufacturer specification and as directed by engineer in charge. , providing and fixing dowel bars ( for pavement works alone ) of 25mm dia. x 1000 mm long and at 300 mm c / c including handling, fixing, straightening, cutting, wastage, and g.i. pipe 40 mm dia. x 150 mm long with end cap over dowels at construction joints & fixing cotton filling sleeve & painting for bond broken etc., complete as per drawings, specifications and as directed by eic. , concertina coil fencing: providing and fixing 750mm dia green colour painted razor type concertina fencing with all required clips, pins. etc as per the specifications ( each concertina coil piece stretch to 9m length ) concertina coil shall be fixed to the m.s. angle with 4 rows of same concertina runner wires over existing x type angle supports as per drawings. rate shall be quoted on running metre of compound wall basis. a. diameter of coil: 750mm, number of circles and number of clips are 72 and 180 in each 9m of length. b. central core wire: core wire shall be of 2.6mm diameter made of highcarbon spring steel of high tensile strength having minimum galvanized coating thickness equivalent to 230 grams per sq.m.c. razor strip: 0.5mm thick hot dip galvanized and of width 19mm having series of barbed punched all along the length at regular intervals having minimum galvanized thickness of 12 microns. hardness of tape should be between 137 180 vpn ( victor penetration number ) d. clips: 1.5mm thick made out of stainless steel. e. runner wire: shall be of same specifications as of central core wire. , supply of jcb on hire basis on all working days from monday to saturday on 8 hrs.shift including driver, assitant, fuel, oil, lubricants, all consumable etc. complete. the quoted rate should include mobilization, operator crews, driver, assistant cost, labour, tools & tackles etc., as directed by the engineer in charge. , supply of poclain pc 200 on hire basis including fuel, oil, lubricants for excavating the existing compacted earth, levelling to required slopes and dumping at designated places within the site premises. the quoted rate should include mobilization, operator crews, driver cost, loading, transporting, unloading, labour, tools and tackles etc. complete as directed by engineer in charge. , supply of 20 feet trailer with tractor on hire basis on all working days from monday to saturday on 8 hrs. shift, inclusive of driver, one assitant, all consumables like diesel etc., with all safety precautions within cpcl refinery premises. the quoted rate should include mobilization, operator crews, driver, assistant cost, loading, transporting from site to scrap yard within refinery premises, unloading, labour for loading and unloading, tools, tackles, wire ropes, pulley blocks, belts, chains etc. for lifting, aligning, tying, stacking etc. all complete as directed by engineer in charge. , supply of 12 t hydra on hire basis on all working days from monday to saturday on 8 hrs shift, inclusive of driver, one assitant, all consumables like diesel etc., with all safety precautions within cpcl refinery premises. the quoted rate should include mobilization, operator crews, driver, assitant cost, loading, transporting, unloading, labour, tools and tackles etc. complete as directed by engineer in charge. , dismantling of structural steel works ( bolted / riveted / welded ) of all descriptions ( taking all necessary safety precautions ) for all heights & depth above & below plinth level including supply of all tools & tackles, consumables, necessary scaffolding etc. providing temporary bracings as required, cutting gusset plates, bolts, nuts, weldings etc, stacking of serviceable materials at designated location / cpcl storage yard / scrap yard within the refinery premises as per direction of engineer in charge. , dismantling of scaffolding / staging ( made of pipes / tubes / frames ) already erected by others including at all locations and levels upto 25 mtr from ground level, including all builtup sections / scaffoldingpipes / compound sections made out of rolled sections and / or plates / bentplates in all types of structural frameworks, floor beams, stairs or anyother strucutral items providing temporary staging including supply of all tools and tackles, consumables, necessary scaffolding etc., including necessary cranes, skilled & unskilled manpower required for the completing the work.transporting and stacking of the serviceable materials to designated place, cleaning & disposal of the site of work from all unserviceable materials transporting to scrap yard / disposal yard within the plant boundary, all complete at all depths andheights, as specified and directed by engineer in charge. , providing and fixing double scaffolding system on the exterior side, upto 25 mtr height from groud level made with 40mm dia m.s. tube 1.5m centre horizontal & vertical tubes joining with cup & lock system with m.s.tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it inserviceable condition for the required duration as approved and removingit there after.the scaffolding system shall be stiffened with bracings, runners, connection with the buildings / strucutures etc. whereverrequired for inspection of work at required locations with essential safety features for the workmen etc.complete as per directions and approval of engineer in charge. the elevational area of the scaffolding and product of height shall be measured for payment purpose. the payment will be made once irrespective of duration of scaffolding. ( scaffolding material shall remains property of contractor and shall be taken back bycontractor after completion of work / instructions of eic ) ...

Balmer Lawrie And Co Limited - Tamil Nadu

29551413 tender for building repairing & painting work 1 providing and repairing with concrete & brickwork plastering and all damaged admin building & operation building, warehouse inner & outer areas chipping & plastering using with chemicals dr. fixit or fosroc or equivalent including scaffolding with 6m height, ware house 12m height using with safety belt and labour fitness certificate with doctor with all tools and tackles etc., 2 providing and painting of interior with two coats of premium emulsion of approved make (asian, dulux, nerolac or equivalent) and shade thoroughly cleaning the surfaces, removing loose burrns, dust, dirt, repairing dents, holes cracks, etc., as per specifications including cost of materials, labour, scaffolding etc., 3 providing and painting of exterior with one coat of primer and two coats of ace or tractor emulsion and shade thoroughly cleaning the surfaces, removing loose burns, dust, dirt, repairing dents, holes cracks, etc., as per specifications including false ceiling area and cost of materials, labour, scaffolding etc., admin, operation buildings, security room (white colour) and compound wall columns and beams (with bl green colour) 4 providing and applying two coats of white wash as per specifications and ceiling (concrete) ware house outside, compound wall inner including scaffolding, adding approved adhesive/glue, preparing the surface etc, as directed, re plastering the damaged patches etc 5 preparing the surfaces of existing wooden doors and windows in all floors and painting with one coat of synthetic enamel paint (asian or equivalent) of approved quality and shade to give an even shade including scrapping wherever required all as directed including all materials, labour, scaffoldings, brushes, tools, equipment, etc., complete. note: 1.necessary painting co efficient shall be allowed as per engineering in charge.2. the above quantity is inclusive of painting coefficient. 6 preparing the surfaces of existing steel members & main gate in all floors and painting with one coat of epoxy paint (asian or equivalent) of approved quality and shade to give an even shade including scrapping wherever required all as directed including all materials, labour, scaffoldings, brushes, tools, equipment, etc., complete. note: 1.necessary painting co efficient shall be allowed as per engineering in charge.2. the above quantity is inclusive of painting coefficient. 7 letter writing including white base coat, green letter and scaffolding etc, 8 supplying & applying of one coat of epoxy primer 15 microns, and two coats of epoxy signal red paint 50 microns of 6 dia or 8 dia fire fighting pipe including supporting angle using power wire brush for cleaning all the surface by manually cleaned etc., user of chopping hammer, emery paper shall be done to clean pitted areas to the satisfaction of site in charge including all materials tools and tackles etc., ...

Military Engineer Services - Tamil Nadu

29052526 as as to vip room at meenambakkam under age ( i ) navy chennai as as to vip room at meenambakkam under age ( i ) navy chennai 1 dismantling of plain or corrugated or semi corrugated steel sheeting as in roof covering complete all as specified and directed by engineer in charge. 2 s&f pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge 3 s&f pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge 4 dismantling wall and ceiling boards ( fibre, pulb, insulation etc ) or insulation boards slabs / blankets any thickness including cover fillets complete all as specified and directed by engineer in charge 5 m&l for suspended false ceiling using e grid 2430, 180 gsm ( exposed ceiling suspension system ) of grid size 600mmx600mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 8mm thick high pressure non asbestos fiber cement decorative board ( e board classic ) in a grid of gi system duly suspended with 4 mm dia gi bar hanger fixed with steel dash fasteners or iron purline from the roof eith adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. the main runners to be secured to structural soffits by hanger @ 1220 mm maximum c / c. the last hanger at the end of each main runner should not be interlocked between main runners @ 610mm c / c, as to form 600 mm x 600 mm grid complete all as specified and directed by engineer in charge 6 taking down shutters of any description n exc 1 sqm each leaf complete all as specified and directed by engineer in charge 7 taking down shutters of any description exc 1 sqm n exc 2 sqm each leaf complete all as specified and directed by engineer in charge 8 taking down shutters of any description exc 1 sqm n exc 2 sqm each leaf and refixing in same opening complete all as specified and directed by engineer in charge 9 taking down wooden chowkhats or frames with shutters ( without taking off shutters from the frames ) of size not exceeding 1.50 square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed by engineer in charge 10 all as per sl item no. 09 above but size exceeding 1.5 square metre and not exceeding 4 square metre each complete all as specified and directed by engineer in charge 11 s&f 30mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both side complete all as specified and directed by engineer in charge 12 s&f 2nd class hard wood glazed and skeleton door shutters 30mm thick open rebated and prepared to receive glass, guage etc ( without sash bars ) , edge of framing plain chemfered ro rounded fitted with cut and mitred beds for securing glass etc size of members of shutters as specified in ssr part i section 8 clasue 8.20 ( a ) complete all as specified and directed by engineer in charge 13 s&f 2nd class hard wood glazed and skeleton ventilator / window 30mm thick open rebated and prepared to receive glass, guage etc ( without sash bars ) , edge of framing plain chemfered rounded fitted with cut and mitred beds for securing glass etc size of members size of members of shutter as specified in ssr part i section 8 clasue 8.20 ( b ) complete all as specified and directed by engineer in charge 14 demolition of un reinforced cement concrete in ground floor and paving not exceeding 15 cm thick ( below or above ground level ) complete all as specified and directed by engineer in charge 15 m&l cement concrete ( 1:3:6 ) , type c 1 using 20mm graded stone aggregate as in filling of steel chowkhats and holdfast including necessary form work complete all as specified and directed by engineer in charge 16 s&f solid pvc door frame of size 50 mm x 47 mm made of 5 mm plain colour pvc sheet reinforced with mild steel square tube complete all as specified in clause 8b.3.1 and shown on page 150 of mes schedule part ii ( 2010 ) complete all as specified and directed by engineer in charge 17 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of ms tubes for top & bottom rails, ms frame covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rails with suitable pvc sheet beading and jointed together with solvent cement, s&fing in the frame at site as per clause 8 b.2.1 of mes schedule part ii ( 2004 ) complete all as specified and directed by engineer in charge 18 s&f anodised aluminium powder coated any colour as approved for ventilator frame and shutter , half fixed and half louvered type without sash bar , incuding 4 mm thick glass , necessary joining cleats , glazing clips , rubber packing , anodised aluminium snap beading , screws etc and section 1.5 mm thick section size complete all as specified and directed by engineer in charge 19 s&f anodised aluminium powder coated any colour as approved window shutters, incl window frame with three track sliding type, without sash bars including guide rollers as reqd nos, including 4mm thick glass necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings as required like suitable handle, star lock etc and minimum 1.5 mm thick section size complete all as specified and directed by engineer in charge note rate incl for providing slide or fix type mosquito proofing shutter and addl track if reqd 20 s&f powder coated ( thickness of powder coating not less than 50 micron ) aluminium door shutters, joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws comprise with door shutter with 85mm x 45mm x 1.5mm thick stiles, 100mm x 43mm x 1.5mm bottom rails and 85mm x 43mm x 1.5mm including lock rails complete all as specified and directed by engineer in charge . 21 s&f 4.8 mm thick sheet glass selected quality approved fixed in position in aluminium / iron / wooden frame work including rubber beading and pointing cleats / glazing with oil putty complete all as specified and directed by engineer in charge 22 s&f framed work such as grills, gratings, etc. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con forming to fe.290.gde e 165 complete all as specified and directed by engineer in charge 23 s&f 6.3 mm thick sheet glass exc 0.5 sqm selected quality approved fixed in position in aluminium / iron / wooden frame work including rubber beading and pointing cleats / glazing with oil putty complete all as specified and directed by engineer in charge 24 s&f ms butt hinges cold rolled medium weight 100mm long complete all as specified and directed by engineer in charge 25 s&f ms butt hinges cold rolled medium weight 75mm long complete all as specified and directed by engineer in charge 26 s&f aluminium, anodised, barrel tower bolts of extruded section 200mm long complete all as specified and directed by engineer in charge 27 s&f aluminium, anodised, barrel tower bolts of extruded section 150mm long complete all as specified and directed by engineer in charge 28 s&f extruded aluminium alloy handles, fabricated type , anodised 125 mm in size complete all as specified and directed by engineer in charge 29 s&f extruded aluminium alloy handles, fabricated type , anodised 75 mm in size complete all as specified and directed by engineer in charge 30 s&f in repairs ms sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12 mm dia and 300 mm long complete all as specified and directed by engineer in charge 31 s&f in repairs second class hard wood small fittings incuding 50 mm thick butt hinges such as brackete of any type , stopper / cleat for door or window, articles n.exc. 200 cu cm each with ms butt hinges cold rolled medium weight 50 mm long complete all as specified and directed by engineer in charge 32 m&l double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainless steel cover , governing pivot made of brass , other parts made of mild steel heavy duty and fixed complete all as specified and directed by engineer in charge 33 s&f in repair aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with beading to wooden frames with aluminium wire staples complete all as specified and directed by engineer in charge 34 m&l 5mm thick pvc sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make pvc frame as per specification and drawing complete all as specified and directed by engineer in charge 35 m&l for 5mm thick solid pvc wall lining consisting of single side prelam pvc sheet of wooden grain printed pvc sheet color inclusive of solvent cement without relevant and fixing at site on pvc frame complete all as specified and directed by engineer in charge 36 s&f anodised aluminium frame for pations with one or more rebates incl joining cleat for fixing etc complete all as specified and directed by engineer in charge 37 s&f sheet glass 5.5 mm thick sheet glass, selected quality in square not exc. 0.50sqm in each pane complete all as specified and directed by engineer in charge 38 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles and rubbish off the premises complete all as specified and directed by engineer in charge 39 m&l glazed ceramic tiles in vertical surface 300 x 450 x 7mm thick incuding rendering 10 mm thick cement mortar ( 1:4 ) to receive tiles in vertical surfaces all as specified set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed by engineer in charge 40 m&l non skid colour ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tiles exc 0.11 sqm but not exc 0.18 sqm as in floors including screed bed or bedding layers of 15 mm thick cement mortar ( 1:6 ) for laying floor finishes all as specified. set and jointed in cement slurry @ 3 kg / sqm and pointed in white or colour cement to match existing surfaces complete all as specified and directed by engineer in charge 41 m&l vitrified ceramic tiles 8 to 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc including screed bed or bedding layers of 15 mm thick cement mortar ( 1:6 ) for laying floor finishes all as specified. all as specified set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by engineer in charge 42 m&l vitrified ceramic tiles 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in skirting / dado etcincuding rendering 10 mm thick cement mortar ( 1:4 ) to receive tiles in vertical surfaces , set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by engineer in charge 43 demolition of un reinforced cement concrete in ground floor and paving not exceeding 15 cm thick ( below or above ground level ) complete all as specified and directed by engineer in charge 44 m&l for 75mm thick cement concrete 1:3:6 type c2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed by engineer in charge 45 supply only 38mmx1, 5 mm plastic dividing strips as in floors complete all as specified and directed by engineer in charge 46 m&l cement concrete ( 1:2:4 ) type b 1 using 20mm graded stone aggregate as in floor topping, 40mm thick, surfaces finished even and smooth without using extra cement complete all as specified and directed by engineer in charge 47 demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed by engineer in charge 48 m&l fly ash brick work with sub class `b bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed by engineer in charge 49 m&l fly ash brick work with sub class ‘b’ brick straight or curved on plan to any radius in half brick wall in cement mortar 1:4 complete all as specified and directed by engineer in charge 50 m&l 10 mm thick cm plaster in cm ( 1:4 ) mixed with water proofing compound @3% by weight of cement over while the padding concrete is still green complete all as specified and directed by engineer in charge 51 supply only liquid water proofing compound 52 m&l for rendering 15mm thick in cm 1:3 cement plaster on fair faces of brick or concrete surfaces finished even and smooth without using extra cement, with water proofing compound @3% by weight of cement complete all as specified and directed by engineer in charge 53 taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and directed by engineer in charge 54 m&l 15mm thick rendering in cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by engineer in charge 55 m&l rendering / plastering, 10mm thick in cement mortar ( 1:4 ) on any face of brick walls or concrete surfaces, using wpc, surfaces finished finished even and smooth without using extra cement complete all as specified and directed by engineer in charge. note: wpc shall be measured and paid separately. 56 cutting chases, pinning in, making good to facing where required and pointed in cement mortar 1:3 and making good cutting exceeding 10 cm exc 20 cm girth complete all as specified and directed by engineer in charge. 57 taking up or down 15mm dia gi steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed by engineer in charge.          58 taking up or down 20mm dia gi steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed by engineer in charge.          59 s&f in gi tube 15 mm dia ( isi marked ) medium grade galvanished with all fittings laid in floors / wall etc. complete all as specified and directed by engineer in charge. 60 s&f in gi tube 20 mm dia ( isi marked ) medium grade galvanished with all fittings laid in floors / wall etc. complete all as specified and directed by engineer in charge. 61 refixing of 15mm dia old steel tubing and connections in new or old position ( walls, ceiling, floors, etc. ) complete all as specified and directed by engineer in charge. 62 refixing of 20mm dia old steel tubing and connections in new or old position ( walls, ceiling, floors, etc. ) complete all as specified and as directed. 63 s&f pvc ball valve 20mm dia high pressure of ptmt with aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed by engineer in charge 64 s&f in repairs gun metal gate valves, with iron wheel head, screwed both ends for gi pipe 20 mm bore and fixed complete all as specified and directed by engineer in charge 65 s&fin repairs vitreous china glass round wash basin, white, flat back, size 580x450 mm excluding taps, waste, chain and plug and porcelin stopper but including brackets complete all as specified and directed by engineer in charge 66 s&f in repairs vitreous china white single piece washdown watercloset pedastal pattern 69 x 36 x 74 cm including necessary lime concrete and 100 mm bore cast iron ‘s’ trap with 550 to 600 mm long neck for connecting wc to branch piece with cement joints, including necessary connections low level flushing cistern 2 / 4 ltrs capacity and jet pressure with nozzle complete all as specified and directed by engineer in charge 67 s&f pvc connections 15 mm size with ptmt nuts of length 450 m complete all as specified and directed by engineer in charge 68 s&f pvc waste pipe 32mm dia of length 900mm ptmt complete all as specified and directed by engineer in charge 69 s&f for 600mmx450mm looking mirror of selected quality glass mounted of 9mm thick of commercial plywood and pvc mouldings frame fancy type complete all as specified and directed by engineer in charge 70 s&f in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. 71 s&f in repair towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden / rawl plugs complete all as specified and directed by engineer in charge 72 s&f in repairs 125mm dia cp brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of cp brass complete all as specified and directed by engineer in charge 73 s&f in repairs 15mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup ( concealed type ) complete all as specified and directed by engineer in charge 74 s&fin repairs stop cock cast copper alloy screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union of 20 mm bore complete all as specified and directed by engineer in charge 75 s&f in repairs fancy type long neck bib taps, cast copper alloy, chromium plated screwed down for 15 mm bore iron pipe or for brass ferrule complete all as specified and directed by engineer in charge 76 s&f shelf ptmt fixed to wall with steel screws and pvc rawl plug complete all as specified and directed by engineer in charge 77 s&f in repairs 19 mm dia mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 nos per running metre and fixed with pvc rawl plugs & steel screws complete all as specified and directed by engineer in charge 78 dismantling asbestos cement / pvc pipe 50 / 75 / 100 mm dia including clamps complete all as specified and directed by engineer in charge 79 s&f in repair low density polythene pipe ( ldpe ) of pressure rating 6 kg per sq.cm, heavy duty laid in trenches size 50mm bore of pipe complete all as specified and directed by engineer in charge 80 s&f 110mm dia pvc ( swr ) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls complete all as specified and directed by engineer in charge 81 s&f 75mm dia pvc ( swr ) pipes single socketed, in any length fixed to walls / floors or in trenches complete all as specified and directed by engineer in charge 82 s&f pvc ( swr ) bends any radius, 110mm bore, fitted with oval access door complete all as specified and directed by engineer in charge 83 s&f bend suitable for 110mm dia pvc ( swr ) pipe complete all as specified and directed by engineer in charge 84 s&f pvc ( swr ) bends any radius, 75mm bore, fitted with oval access door complete all as specified and directed by engineer in charge 85 s&f pvc ( swr ) reducers any radius 110mm bore complete all as specified and directed by engineer in charge 86 s&f 110mm bore pvc ( swr ) junction, single ( single t ) equal or unequal with or without door access complete all as specified and directed by engineer in charge 87 s&f pvc ( swr ) vent cowl 75mm dia complete all as specified and directed by engineer in charge 88 s&f contemporary health faucet with metal hose and holder as available in polished chrome mimiumum 500 gm weight make: kohler catalague no. 12927in cp or equivalent in jaquar / grohe as approved by age ( i ) 89 s&f self adhesive metal bathroom corner rack storage shelves of dimesions 36x26.7 x6 cm complete all as specified and directed by engineer in charge 90 m&l for applying two coat of white wash on old decorated surfaces of ceiling and cornices including preparation of old plastered surfaces by brooming down or steel wire brushing scrapping down smoke shoots, moulds, moss and efforescent salts, trading oil and greasy spots etc complete all as specified and directed by engineer in charge 91 m&l preparation of new undecorated plastered surface of walls and applying two coat of colour distemper oil emulsion over one coat of primer on wall complete all as specified and directed by engineer in charge 92 m&l for complete removal of existing treatment and applying two coat of oil bound distemper ( white or tinted ) over a coat of whiting on wall complete all as specified and directed by engineer in charge 93 m&l preparation of plastered surfaces of wall and applying two coats of exterior wheather coats ( as per manufacturers instruction ) over a coat of wall putty complete all as specified and directed by engineer in charge 94 m&l for complete removal of existing treatmentand applying two coats of exterior wheather coats ( as per manufacturers instruction ) over a coat of wall putty complete all as specified and directed by engineer in charge 95 m&l for prepration of new or previously untreated surface and applying two subsequent coat of white wash on walls complete all as specified and directed by engineer in charge 96 m&l for removing loose dust partcies and surface is wet approxmiate damp proof cleaning to be done and appying one coat of wall primer then applying two coats of texture painting over the exisitng wall of desired pattern and proper application tools as per design and direction given by enginner in charge 97 m&l for 12mm thick toughened glass door and fitted to top and bottom hardwood chamfered or rounded fitted with cut and mitred beads for securing glass with necessary pivot hinge, , cut outs and holes suitable for h handle ( 2nos for each side ) , backer rod, silicon sealant with ceiling bearing ( including two nos of locking arrengments ) complete all as specified and directed by the engr in charge. 98 m&l 12mm thick toughened glass partition with hatching design / pattern as approved and fitted to top and bottom rail to floor and ceiling hardwood chamfered or rounded fitted with cut and mitred beads for securing glass with necessary fitting arrangements and gaps are filled with silicon sealant complete all as specified and as directed by age ( i ) 99 m&l for french polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats as directed by the age ( i ) 100 m&l for two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces of any description not other wise described over 10 cm width or girth including preparation complete all as specified and as directed. 101 m&l preparing of old decorated wood or wood base surface of any description over 10 cm width or grith applying one coat of synthetic enamel paint complete all as specified and as directed. 102 m&l for point wiring for one light point controlled by one switch with 1.5 sqmm ( nominal area ) unsheathed multi stranded copper conductor pvc insulated cable 1100 volts grade single core frls drawn with pvc conduit of 19 / 20 mm dia, orasper is concealed frls wiring, along with 1.5 sqmm unsheathed multi stranded copper conductor cable pvc insulated 1100 volts grade as earth continuity conductor connected to common earth dolly fixed to wall / ceiling roof excluding modular metal flsh box and white cover palate with frame the switches, sockets, fan regulator etc as required suitable for modular type fitting / fixture trll complete all as specified and directed by engineer in charge 103 all as per sl item no. 102 above but for one fan / exhaust fan point controlled by one regulator / switch. 104 all as per sl item no. 102 above but for one 3 pin socket outlet 5 amps socket on same board 105 all as per sl item no. 102 above but for one 3 pin socket outlet 5 amps socket on independent board 106 all as per sl item no. 102 above but with 2.5 sqmm cable for one 3 pin socket outlet 15 amps on independent board with 2.5 sqmm cable as earthing conductar 107 s&f for modular switch, 1 way, 6a, 1 module complete all as specified and directed by engineer in charge 108 s&f for modular switch, 1 way, 16a, 1 module complete all as specified and directed by engineer in charge 109 s&f modular socket, 6a, 2 / 3 pin combined, 2 module complete all as specified and directed by engineer in charge 110 s&f modular socket, 6a / 16a, 2 / 3 pin combined, 2 module complete all as specified and directed by engineer in charge 111 s&f for modular white cover plate with frame, 2 module complete all as specified and directed by engineer in charge 112 s&f for modular white cover plate with frame, 3 module complete all as specified and directed by engineer in charge 113 s&f for modular white cover plate with frame, 4 module complete all as specified and directed by engineer in charge 114 s&f for modular white cover plate with frame, 6 module complete all as specified and directed by engineer in charge 115 s&f for modular white cover plate with frame, 12 module complete all as specified and directed by engineer in charge 116 s&f for modular metal flush box, 2 module complete all as specified and directed by engineer in charge 117 s&f for modular metal flush box, 3 module complete all as specified and directed by engineer in charge 118 s&f for modular metal flush box, 4 module complete all as specified and directed by engineer in charge 119 s&f for modular metal flush box, 6 module complete all as specified and directed by engineer in charge 120 s&f for modular metal flush box, 12 module complete all as specified and directed by engineer in charge 121 m&l for ceiling rose, 3 phase fire rated polycarbonate, isolated body complete all as specified and directed by engineer in charge 122 s&f stepped type electronic fan regulator modular type all as specified and directed by engineer in charge complete all as specified and directed by engineer in charge 123 s&f for sub main wiring for circuit of size 2 x 6.0 sq.mm along with earth wire of size 1 x 6 sq.mm, single core, pvc insulated copper coductor ( frls ) cable in concealed / surface / recessed pvc conduit complete all as specified and directed by engineer in charge 124 s&f for sub main wiring for circuit of size 2 x 4.0 sq.mm along with earth wire of size 1 x 4 sq.mm, single core, pvc insulated copper coductor ( frls ) cable in concealed / surface / recessed pvc conduit complete all as specified and directed by engineer in charge 125 s&f power unit for 1.5 / 2 ton a.c including connecting electric connections, complete all as specified and directed by engineer in charge 126 s&f sheet metal enclosure powder coated single door outdoor type for distribution board, spn 8 way db with degree of protection ip 54 , detachable gland plate, box insertion marks •, circuit identification label •, neutral link , earth link , tin plated copper bus bar including , disconnecting electric connections, dismantling from position unserviceable dbs for taking into credit complete all as specified and directed by engineer in charge 127 s&f mcb spn 32 63 a , b curve including , disconnecting electric connections, complete all as specified and directed by engineer in charge 128 s&f mcb sp 06 a to 32 a , b curve including , complete all as specified and directed by engineer in charge 129 s&f 2x2 led fitting 36 watt , 3600 lm , 6500 k suitable for led recessed full lit luminaire with glare free uniform illumination with longer life and less maintenance complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size and lamp complete all as specified and directed internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. complete all as specified and directed . make : crompton lctlrne 36 fo cdl, or equivalent in philips, wipro as approved by age ( i ) 130 s&f ceiling fan sweep 1200 mm complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by engineer in charge. 131 s&f exhaust fan 250 mm 5 blade exhaust fan ( white ) , pvc body, rust proof body and blades, double ball bearing with noiseless operation, 1400 rpm complete with louvers including making suitable opening at suitable height, and provision of nuts and bolts on the wall for fixing the exhaust fan complete all as specified and directed by engineer in charge 132 s&f water heater storage type, electric, capacity 25 litres.bee 5 star rated complete all as specified and as directed 133 s&f air cooled split unit air conditioner electric driven, single phase of capacity of 1.5 tr, bee 5 star rated complete all as specified and as directed 134 s&f voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 v to 300 v with output voltage stabilized at 230 v with accuracy of ± 2.5% and of capacity 3.0 kva 135 m&l for new earthing complete with galvanised steel plate earth electrode 600x600x6mm thick buried directly in ground ( earth pit not less than 2.25 meter below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level connected to gi wire 4mm at two points by means of bolts and nut, check nut and washers including charcoal dust, common salt, necessary excavation in hard / dense soil, returning filling in and removal of surplus soil to a distance up to 50metres, pcc pit in 1:3:6 type ci ( using 20mm grade stone aggregate ) rcc 1:2:4 type b 1 ( using 20mm grade stone aggregate ) 50mm thick pit cover, reinforced with 8mm dia tmt bars 75mm c / c, both ways ms handle 12mm dia, gi funnel, wire mesh and gi watering pipe of 20mm bore gi ( light grade ) and earth lead protection pipe 20mm bore ( light grade ) all as specified, directed and shown in electrical plate no 3 of ssr part i including testing complete. note : gi strip and protection pipes 20 mm gi light grade up to 7.5 metre is included in unit rate and beyond that the same will be measured separately. 136 s&f for gi wire 4 mm on wall / batten or recessed or buried in ground all as directed...

Chennai Petroleum Corporation Limited - Tamil Nadu

28786034 civil works for silo i for coke handling system in manali refinery of cpcl civil works for silo i deck slab and other balance works in silo i for coke handling system in manali refinery of cpcl , providing necessary barricading workswith 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3m, embedding the same in firm ground with necessary foundation works etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works.the same will be the property of contractor. , providing&laying dry rubble soling (hard core) with 20 to 40 mm size metal, under foundations/ ground floor slab (grade slab) etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors etc., complete as per drawings, specifications and as per thedirections of engineer in charge. , providing, mixing and laying of pcc 1:4:8 nominal mix using 40 mm and downgraded coarse aggregate and using opc (53 grade) for any thickness for all depths belowraft ,pile cap etc., including shuttering, tamping, ramming, vibrating, curing, etc., all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete, as per drawings, specifications and as directed by engineer in charge. , providing, mixing and laying in position reinforced cement concrete (rcc) of grade m35 with 20mm and down graded coarse aggregates and minimum cement content of 400kg/cu.m as per is 456:2000 using 53 grade ordinary portland cement in sub structurefor all depths upto 450mm from ground level along with cost of admixtures, labour charges,tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.including single pour concreting as specified in drawing,(excluding the cost ofreinforcement and shuttering), etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete (rcc)of grade m30 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg/cu.m ; as per is 456:2000using 53 grade ordinary portland cement in super structurefor height above 20m upto 50m including silo wall concreting , including cost of admixtures,labour charges, tools and tackles,providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. (excluding the cost of reinforcement, shuttering), etc. all complete as specified,and directed by engineer in charge. , providing and fixing formwork in super structures forheight above 20m upto 50mfrom ground level,including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents ofapproved make, for straight/inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500d for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in using cement mortar 1:6 (1 cement:6 m sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam/slab, embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing 20 mm thick cement plaster in 2 coats, 1st coat of 12 mm thick in cement mortar 1:4(1 cement:4 m sand) & 2nd coat of 8 mm thick in cement mortar 1:4 (1 cement:4 m sand)plain cement plaster outside/inside the building/boundary wall finished to a smooth finish including providinggrooves at junctions of two dissimilar materials all complete as directed by eic. , providing 6mm thick cement plaster in cement mortar 1:3 (1cement:3 m sand by volume) on roof ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges, material costs, tools and tackles etc.as per specifications and as directed by the engineer in charge. , providing & applying interior paint one coat of emulsion primer & filling cervices, if any with putty & applying two coats of acrylic distemper paint of asian / approved equivalent make, as per the manufacturer’s specifications including necessary scaffolding, brushing, cleaning & surface preparation with plaster of paris punning etc. complete as per specifications, drawings and as directed by engineer in charge. , providing and applying three coats of approved white wash (comprising of fat lime, water , gum with hot water and sodium chloride with hot water) in interior surfaces as per the specifications including necessary scaffolding and surface preparation etc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of premium acrylic emulsion exteriorpaintof required shade and includingsurface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty , necessary scaffolding etc, etc all complete as per specifications and directions of engineer in charge. , providing & laying 15mm thick tile acid resistant tiles (vitrified) to floors of approvedmake bedding & joints filled with appropriate acid proof cement . all work completeas per manufacturer’s specifications, drawing & as directed by engineer in charge. , providing & laying acid resistant tiles (vitrified)to 10 to 12 mm thick for walls of approvedmake with applying 2 coats (to the base concrete)of mixture of general purpose polymer (bonding agent ) mixed with opc cement, sprinkling silica to make surface rough . bedding mortar of 8 to 10 mm thickness in 1:3 ratio with 5 % general purpose polymer added to cement .joints of min. width 5 to 8 mm raked, cleaned & filled with appropriate acid proof cement . all work completeas per manufacturer’s specifications, drawing & as directed by engineer in charge. , providing and fixing pressed steel door and window frames of size (assorted size out of) overall 125mm x60mm section, of required profile conforming to is: 4351,made of 16 swg pressed steel including/ consisting of:i)3 mm thick ms flat spacers welded to frame @ 500mmc/c and at holdfast locations.ii)filling the hollow frame section with concrete. iii)ms angle(20mmx20mmx3mm) horizontal tie member belowfloor finish. iv)ms holdfasts (200mmx25mmx6mm) welded tospacers. v)fixing to masonry (by grouting the holdfasts with m 15grade concrete in minimum 250mm x 100mm x 100mmsized hole)/ fixing to rcc (by minimum 100mm long, 12 mm dia metallic counter sunk anchor fasteners) vi)ms pad plates (40mm x150mm x 3mm) & gi mortar guard welded to frame at hinge and other hardware locations.vii)metering of joints between horizontal and verticalmembers, grinding and smoothening of welding, cleaningof frame surface, finishing (synthetic enamel painting/electrostatic powder coating/ polyurethane (pu) coating),making true alignments and surfaces etc. all complete.notes:1)cumulative length of all horizontal and vertical frame members shall be measured for payment. frames painted with polyurethane (pu) paint coating over epoxy primer. , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40 mm overall thickness; and consisting of/ including:(i) 3 mm thick ms flat all along perimeter(ii) packing the shutter with mineral wool (48 kg/cum)without gap(iii) strengthening with 18 swg gi vertical stiffeners@200 c/c (iv) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware etc. (v) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @600 c/c maximum(vi) hardware and vision panel as required.(vii) grinding and smoothening of welding, cleaning, finishing (synthetic enamel painting/ polyurethane (pu) coating/ electrostatic powder coating), making true alignments and surfaces etc. all complete.notes:only the net shutter(s) area shall be measured for payment. single shutter painted with electrostatic powder coating with following hardware: (i) over head hydraulic door closer (heavy duty).(ii) ss 304 grade 16 mm dia 250mm long aldrop on both sides of shutter.(iii) spring loaded heavy duty door stopper(iv) ss 304 grade 19 mm dia.200 mm long handle on both side of shutter.(v) 10 mm dia ss 304 tower bolt (250mm long for 2100mm height & 600mm long for 2500mm height). , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40 mm overall thickness; and consisting of/ including:(i) 3 mm thick ms flat all along perimeter(ii) packing the shutter with mineral wool (48 kg/cum)without gap(iii) strengthening with 18 swg gi vertical stiffeners@200 c/c (iv) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware etc. (v) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @600 c/c maximum(vi) hardware and vision panel as required.(vii) grinding and smoothening of welding, cleaning, finishing (synthetic enamel painting/ polyurethane (pu) coating/ electrostatic powder coating), making true alignments and surfaces etc. all complete.notes:only the net shutter(s) area shall be measured for payment. double shutter painted with electrostatic powder coating with following hardware:(i) over head hydraulic door closer (heavy duty).(ii) ss 304 grade 16 mm dia 300mm long aldrop on bothsides of shutter.(iii) spring loaded heavy duty door stopper.(iv) ss 304 grade 19 mm dia.200 mm long handle on both side of shutter.(v) 10 mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height) (vi) 2mm thick 25mmx 25mm gi angles (vertical) welded to each shutter at the meeting point of double shutter. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases etc.using non shrink grout of approved make equivalent including supply of material,roughening surface, cleaning with compressed air/water jets, ramming, curing,labour charges etc.all complete as directed by engineer in charge. , supplying structural steelconforming to is:2062 grade a, (yield strength 250.0 n/mm2) transporting, storage, straightening, cleaning, fabricating welded / bolted structural steel workin columns, beams, trusses, purlins, platforms, ladders, monorails, staircases, supports, strengthening of steel members etc. at site to line and level, including supply of bolts, supply of shim plates & approved welding electrodes, including making templates, welding, bolting, erection bolting, splicing etc. as per specifications and drawing and as directed by the owner/consultant. cutting to required size, straightening/ bending if required, edge preparation, cleaing, scrapping and welding, preheating, finishing edges by grinding, fixing in line ans level, including preparing the surface for painting, surface cleaing, wire brushing, removal of mill scale, dust, rust, oil or grease etc.., complete along with providing paint system as follows: (a) applying inorganinc zinc silicate coat 50micron dft (b) one coat of epoxy primer paint 50 micron dft each (c) two coat of anti rust epoxy top coat paint 50micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after gritblast cleaing in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , providing and placing / spreading 500 microns thick hdpe sheet / film including laps as per drawing & as directed by engineer in charge. , supplying, assembling and installing 1000 mm high satin finish stainless steel (ss 304 grade) tubular railing of approved design in staircases, ramps, around floor cutouts etc. consisting of:1. 50mm dia ss pipe top handrail 2. 32 mm dia ss pipe balusters (at every third step forstaircase, @ maximum 1200mm c/c for ramp, floor cutouts)3. 3 nos minimum 18mm dia ss pipe intermediate handrails.including:1. fixing balusters to floor with 4 nos bolts änd 8mm thick, 100mm dia ss base plate & ss cap/collar.2. fixing top handrail to the balusters with 12mm dia ss bar connector & 6mm thick ss saddle plate.3. fixing intermediate handrails to the balusters with 12mm dia ss bar connector.4. all end caps, decorative caps over balustrades,necessary bending, welding, polishing of allwelded joints (length of top handrail shall be measured for payment). , supplying,handling,transporting to site of work and fixing approved electroplated steel heavy duty mechanical anchor fasteners,of 12mm dia at specified positions on concrete floors,roofs,beams( sides and bottom), walls,columns etc. according to manufacturers specifications including all accessories like nuts,washers etc. of required size,testing,necessary scaffolding,drilling of the holes in concrete surface with electric drill,cleaning of holes with air blowout & wire brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as per manufacturers specification and directed by engineer in charge. , supplying,handling,transporting to site of work and fixing approved electroplated steel heavy duty chemical anchor fasteners , packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors,roofs,beams( sides and bottom), walls,columns etc. according to manufacturers specifications including all accessories like nuts,washers etc. of required size,testing,necessary scaffolding,drilling of the holes in concrete surface with electric drill,cleaning of holes with air blowout & wire brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge....

Reserve Bank Of India - Tamil Nadu

28050657 carefully dismantling and removing the existing kota / cuddapah ( kadapa ) / granite stone slabs / ceramic / vitrified tiles / i.p.s / cement plaster finish of any thickness, on the floor of the entrance lobby, landing slabs, sills of door / window / openings & risers of steps, skirtings and walls, in the staircase including bed / back mortar / cement plaster of any thickness using approved method to expose the r.c.c / masonry surfaces, disposing and carting away the debris and nonsalvageable materials generated from the work, out of the colony premises, shifting and stacking the salvageable items at locations shown by the bank?s engineer within the colony premises etc, complete as directed by the banks engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the p.c.c floor in the entrance lobbies / r.c.c floor slabs of the landings in the staircase, exposed as per item no. 1 above, by thorough cleaning, using wirebrush / broom after sprinkling water, providing and applying a priming coat of cement slurry, providing, cutting to the required sizes , from 1618 mm thick, machine cut / polished granite slabs of approved quality, size and shade, granite slabs having approved sizes, laying / fixing true to line and level, in approved pattern over bed / back mortar layer prepared by mixing approved make portland cement and river sand in the ratio 1:4 and laid over the prepared surface, for an average consolidated thickness of 2025 mm, set with a floating layer of cement slurry, with a minimum cement content of 3.30 kg per sqm and joints grouted with approved make and quality tile grouts / jointing compounds admixed with pigments.pl refer to the tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the r.c.c floor slab / sills of doors / windows / openings / risers of steps / masonry, exposed as per item no.1 above, by thorough cleaning, using wire brush / broom, after sprinkling water, providing and applying a priming coat of cement slurry, providing, cutting to required sizes, laying / fixing, true to line and level / plumb, 1618 mm thick, 100150 mm wide machine cut / polished granite slabs of approved sizes, quality and shade, as sills of doors / windows / openings ( in single piece ) , skirting on both sides of the steps in l shape ( single piece for each pair of treads and risers ) and borders in the floor of entrance lobbies / landings of staircase ( joints in border shall match with joints of the slabs laid as flooring ) etc pl refer to the tender document for detailed description quote rate per unit exclusive of gst all as above under item no. 3 above, but for 250 300 mm wide granite slabs, in single piece, as treads of steps in the staircase. the exposed edge on the front of each step shall be half rounded and machine polished to obtain the same finish of the prepolished top surface. each of the granite slab treads shall be provided with numbers of grooves having a minimum width and depth of 3 mm each, cut parallel to the exposed edge at an equal spacing. ( basic price of granite slabs ? exgodown / yard at chennai rs. 2, 000 / per sqm, excluding taxes, local transport / cartage, handling, loading and unloading etc, required for delivery at site. the bidders shall consider the same while quoting their rates. the bank shall not entertain any separate claim towards these elements ) pl refer to the tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the masonry / r.c.c members of the walls, exposed as per item no. 1 above, by raking the loose mortar in the joints, watering and thorough cleaning using wire brush / broom, providing and rendering, cement plaster in cm 1:3, for an average consolidated / finished thickness of 20 mm, prepared by providing and mixing approved make portland cement and river sand, true to plumb, level and line, to repair the damaged portions of plaster on walls / r.c.c members in patches. the surface of the wet plaster shall be finished smooth using trowels / floats, with a coat of neat cement paste, made with portland cement @ 3.30 kg / sqm. the rate shall include all materials including wastages, labour, all leads and lifts, transport & tools, required for the finished work, all as directed by the banks engineerpl refer to the tender document for detailed description quote rate per unit exclusive of gst psuitably preparing the surface of the soffits ( ceilings ) of roof / floor slabs, waist slabs of staircase flights etc, by removing the loose layers of existing white wash / distemper by manual scrapping and sandpapering to make the surfaces level and free from loose matter / paint layers, flakes, dust etc, to make the surfaces, suitable to receive fresh coats of primer / paint, providing and applying two or more coats of white lime wash admixed with aquamarine blue / alum to obtain the best finish. the rate shall include all materials, labour, transport, tools, scaffolding etc, required for the finished work, all as per site conditions and as directed by the banks engineer. the rate shall also include disposing and carting away the dust / debris generated from the work from the bank?s premises pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the surface of the walls and soffits / vertical sides of beams, hand rail walls on the sides of stairs etc, by scraping, sand papering & dusting of loose layers / flakes of existing paint finishes, providing and applying required thickness of white cement based putty to fill up, level and smoothen the surface, wherever required in patches , to make the surfaces, suitable to receive fresh coats of primer / paint, providing and applying a coat of exterior grade special primer, recommended by the paint manufacturer, two or more coats of stretchable 100% acrylic emulsion, water repellent semielastomeric exterior grade paint of approved make, shade and quality as per manufacturers specifications, standard specifications of the bank and as directed by the banks engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the wooden surfaces of joineries like doors, windows, ventilators or any other wooden members by removing the loose paint, sand papering, filling of the cracks / crevices / fissures etc with chalk powder putty and making the surface smooth by sand papering , dusting etc, to make the surfaces suitable to receive fresh coats of primer / paint, providing and applying two or more coats of approved quality, make and shade, satinfinish synthetic enamel paint over a coat of approved quality and make wood primer as per the standard specifications of the bank, manufacturer?s specifications and as directed by the bank?s engineer to get the sheen / finish to the satisfaction of the bank?s engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the surfaces of the metallic and wooden surfaces of the ladders leading to the terraces, including hand rails and rungs, and the handrails over the parapet walls, around the floor, on which the ladder is mounted, by removing rust scales, laitance, loose paints etc, by sand papering & dusting etc, to make the surfaces suitable to receive fresh coats of primer / paint, providing and applying one coat of zinc chromate or wood primer to metallic or wooden surfaces respectively, providing and applying two or more coats of synthetic enamel paint, over the surfaces, prepared as above, to get the required sheen / finish as per the standard specifications of the bank, as per manufacturers instructions and as directed by the bank?s engineer. approximate overall dimensions of the ladder 3.50 m x 0.70 m and that of the railing over the parapet wall 2.30 m x 0.60 m. pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the exposed surfaces of the wooden railings on the top of the staircase hand rail walls, by thorough scrapping, sand papering, dusting, cleaning, filling and levelling of holes / crevices / cavities / cracks / knots / defects with approved quality and make wood putty / fillers / sealers, smoothening the surface so prepared by sand papering / dusting etc, providing and applying two or more coats of french spirit polish of approved make including addition of necessary pigments, to get the required finish / sheen etc, as directed by the bank?s engineerpl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the exposed surfaces of the metallic and wooden panels of the eb meter panel boxes and wooden boxing above them at the entrance lobby of staircases, by removing rust scales, laitance, loose paints etc, by sand papering & dusting etc, to make the surfaces suitable to receive fresh coats of primer / paint, providing and applying one coat of zinc chromate or wood primer to metallic or wooden surfaces respectively, providing and applying two or more coats of synthetic enamel paint, over the surfaces, prepared as above, to get the required sheen / finish as per the standard specifications of the bank, as per manufacturers instructions and as directed by the bank?s engineer. approximate overall dimensions of the panel box 1.45 m x 1.20 m 0.36 m for eb meter panel box and 1.05 m ( average ) x 0.45 m x 0.36 m for the wooden boxing above it pl refer to the tender document for detailed description quote rate per unit exclusive of gst...

Reserve Bank Of India - Tamil Nadu

27974965 carefully dismantling and removing the existing kota / cuddapah ( kadapa ) / granite stone slabs / ceramic / vitrified tiles / i.p.s / cement plaster finish of any thickness, on the floor of the entrance lobby, landing slabs, sills of door / window / openings & risers of steps, skirtings and walls, in the staircase including bed / back mortar / cement plaster of any thickness using approved method to expose the r.c.c / masonry surfaces, disposing and carting away the debris and nonsalvageable materials generated from the work, out of the colony premises, shifting and stacking the salvageable items at locations shown by the bank?s engineer within the colony premises etc, complete as directed by the banks engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the p.c.c floor in the entrance lobbies / r.c.c floor slabs of the landings in the staircase, exposed as per item no. 1 above, by thorough cleaning, using wirebrush / broom after sprinkling water, providing and applying a priming coat of cement slurry, providing, cutting to the required sizes , from 1618 mm thick, machine cut / polished granite slabs of approved quality, size and shade, granite slabs having approved sizes, laying / fixing true to line and level, in approved pattern over bed / back mortar layer prepared by mixing approved make portland cement and river sand in the ratio 1:4 and laid over the prepared surface, for an average consolidated thickness of 2025 mm, set with a floating layer of cement slurry, with a minimum cement content of 3.30 kg per sqm and joints grouted with approved make and quality tile grouts / jointing compounds admixed with pigments.pl refer to the tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the r.c.c floor slab / sills of doors / windows / openings / risers of steps / masonry, exposed as per item no.1 above, by thorough cleaning, using wire brush / broom, after sprinkling water, providing and applying a priming coat of cement slurry, providing, cutting to required sizes, laying / fixing, true to line and level / plumb, 1618 mm thick, 100150 mm wide machine cut / polished granite slabs of approved sizes, quality and shade, as sills of doors / windows / openings ( in single piece ) , skirting on both sides of the steps in l shape ( single piece for each pair of treads and risers ) and borders in the floor of entrance lobbies / landings of staircase ( joints in border shall match with joints of the slabs laid as flooring ) etc pl refer to the tender document for detailed description quote rate per unit exclusive of gst all as above under item no. 3 above, but for 250 300 mm wide granite slabs, in single piece, as treads of steps in the staircase. the exposed edge on the front of each step shall be half rounded and machine polished to obtain the same finish of the prepolished top surface. each of the granite slab treads shall be provided with 3 numbers of grooves having a minimum width and depth of 3 mm each, cut parallel to the exposed edge at an equal spacing. ( basic price of granite slabs ? exgodown / yard at chennai rs. 2, 000 / per sqm, excluding taxes, local transport / cartage, handling, loading and unloading etc, required for delivery at site. the bidders shall consider the same while quoting their rates. the bank shall not entertain any separate claim towards these elements ) pl refer to the tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the masonry / r.c.c members of the walls, exposed as per item no. 1 above, by raking the loose mortar in the joints, watering and thorough cleaning using wire brush / broom, providing and rendering, cement plaster in cm 1:3, for an average consolidated / finished thickness of 20 mm, prepared by providing and mixing approved make portland cement and river sand, true to plumb, level and line, to repair the damaged portions of plaster on walls / r.c.c members in patches. the surface of the wet plaster shall be finished smooth using trowels / floats, with a coat of neat cement paste, made with portland cement @ 3.30 kg / sqm. the rate shall include all materials including wastages, labour, all leads and lifts, transport & tools, required for the finished work, all as directed by the banks engineerpl refer to the tender document for detailed description quote rate per unit exclusive of gst psuitably preparing the surface of the soffits ( ceilings ) of roof / floor slabs, waist slabs of staircase flights etc, by removing the loose layers of existing white wash / distemper by manual scrapping and sandpapering to make the surfaces level and free from loose matter / paint layers, flakes, dust etc, to make the surfaces, suitable to receive fresh coats of primer / paint, providing and applying two or more coats of white lime wash admixed with aquamarine blue / alum to obtain the best finish. the rate shall include all materials, labour, transport, tools, scaffolding etc, required for the finished work, all as per site conditions and as directed by the banks engineer. the rate shall also include disposing and carting away the dust / debris generated from the work from the bank?s premises pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the surface of the walls and soffits / vertical sides of beams, hand rail walls on the sides of stairs etc, by scraping, sand papering & dusting of loose layers / flakes of existing paint finishes, providing and applying required thickness of white cement based putty to fill up, level and smoothen the surface, wherever required in patches , to make the surfaces, suitable to receive fresh coats of primer / paint, providing and applying a coat of exterior grade special primer, recommended by the paint manufacturer, two or more coats of stretchable 100% acrylic emulsion, water repellent semielastomeric exterior grade paint of approved make, shade and quality as per manufacturers specifications, standard specifications of the bank and as directed by the banks engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the surface of the walls and soffits / vertical sides of beams, hand rail walls on the sides of stairs etc, by scraping, sand papering & dusting of loose layers / flakes of existing paint finishes, providing and applying required thickness of white cement based putty to fill up, level and smoothen the surface, wherever required in patches , to make the surfaces, suitable to receive fresh coats of primer / paint, providing and applying a coat of exterior grade special primer, recommended by the paint manufacturer, two or more coats of stretchable 100% acrylic emulsion, water repellent semielastomeric exterior grade paint of approved make, shade and quality as per manufacturers specifications, standard specifications of the bank and as directed by the banks engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the wooden surfaces of joineries like doors, windows, ventilators or any other wooden members by removing the loose paint, sand papering, filling of the cracks / crevices / fissures etc with chalk powder putty and making the surface smooth by sand papering , dusting etc, to make the surfaces suitable to receive fresh coats of primer / paint, providing and applying two or more coats of approved quality, make and shade, satinfinish synthetic enamel paint over a coat of approved quality and make wood primer as per the standard specifications of the bank, manufacturer?s specifications and as directed by the bank?s engineer to get the sheen / finish to the satisfaction of the bank?s engineer pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the surfaces of the metallic and wooden surfaces of the ladders leading to the terraces, including hand rails and rungs, and the handrails over the parapet walls, around the floor, on which the ladder is mounted, by removing rust scales, laitance, loose paints etc, by sand papering & dusting etc, to make the surfaces suitable to receive fresh coats of primer / paint, providing and applying one coat of zinc chromate or wood primer to metallic or wooden surfaces respectively, providing and applying two or more coats of synthetic enamel paint, over the surfaces, prepared as above, to get the required sheen / finish as per the standard specifications of the bank, as per manufacturers instructions and as directed by the bank?s engineer. approximate overall dimensions of the ladder 3.50 m x 0.70 m and that of the railing over the parapet wall 2.30 m x 0.60 m. pl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the exposed surfaces of the wooden railings on the top of the staircase hand rail walls, by thorough scrapping, sand papering, dusting, cleaning, filling and levelling of holes / crevices / cavities / cracks / knots / defects with approved quality and make wood putty / fillers / sealers, smoothening the surface so prepared by sand papering / dusting etc, providing and applying two or more coats of french spirit polish of approved make including addition of necessary pigments, to get the required finish / sheen etc, as directed by the bank?s engineerpl refer to the tender document for detailed description quote rate per unit exclusive of gst suitably preparing the exposed surfaces of the metallic and wooden panels of the eb meter panel boxes and wooden boxing above them at the entrance lobby of staircases, by removing rust scales, laitance, loose paints etc, by sand papering & dusting etc, to make the surfaces suitable to receive fresh coats of primer / paint, providing and applying one coat of zinc chromate or wood primer to metallic or wooden surfaces respectively, providing and applying two or more coats of synthetic enamel paint, over the surfaces, prepared as above, to get the required sheen / finish as per the standard specifications of the bank, as per manufacturers instructions and as directed by the bank?s engineer. approximate overall dimensions of the panel box 1.45 m x 1.20 m 0.36 m for eb meter panel box and 1.05 m ( average ) x 0.45 m x 0.36 m for the wooden boxing above it pl refer to the tender document for detailed description quote rate per unit exclusive of gst...

Reserve Bank Of India - Tamil Nadu

27876132 carefully dismantling and removing the existing ceramic tile flooring / skirting / wall dado including bed back mortar, wall plastering etc., in interior area of certain flats by approved methods, so as to expose the r.c.c floor slab / brick wall without damaging the slab / wall and cleaning, removal of debris etc. out of banks premises all complete as directed by the banks engineer quote rate per unit exclusive of gst carefully dismantling and removing the existing open gi plumbing lines wherever required, providing, cutting, fixing, testing and commisioning concealed waterlines of 20mm diameter using cpvc threaded pipe of sdr 11 including all the necessary specials like elbows, tees, couplings etc. all the concealed lines shall be properly fastened to the wall using gi clamps @maximum spacing of 450mm. rate shall be inclusive of making necessary cutting and chasing on the walls to receive the plumbing lines, placing the plumbing line, properly packing using cement mortar admixed with waterproofing chemicals, followed by pasting approved quality fiber mesh on the surface of the chasing, wastages, pressure testing for leakage, removal of debris etc. actual linear measurement shall be reckoned for payment purpose quote rate per unit exclusive of gst carefully dismantling and removing the existing open waste lines of wash basins, providing and fixing new pvc pipes of 40 mm diameters ( minimum test / working pressure 6 kg / sq.cm ) of approved quality and make, including all fittings, of the same manufacturer of the pipes or approved equivalent for the wash basin and laying the pipes in concealed manner by cutting chases in the wall / floor etc. complete. the rate shall inclusive of cutting, jointing of pipes with fittings and making good the damages by necessary plastering, including testing of joints / pipelines, etc. for leakage etc. all complete as directed by the banks engineer quote rate per unit exclusive of gst preparing the surface of the masonry / rcc walls by raking, watering and thorough cleaning using wire brush, broom, providing and applying average 20 to 25 mm thick cement plaster using cm 1:4 comprising of a first coat of 12 mm thickness, and a second coat of 9 to 12mm thickness ) using approved quality opc and river sand, true to plumb, level and line. the wall plaster shall have an even surface and shall be finished with recessed joints to receive the tile dado / skirting. the rate shall include for curing, labour, all leads and lifts, etc. required for the finished work, removal of debris etc. all as directed by the bank?s engineer quote rate per unit exclusive of gst preparing the surface of the r.c.c floor slab by thorough cleaning and priming with cement slurry admixed with approved make and quality water proofing compounds, providing, mixing, laying, spreading, levelling and manually consolidating using hand rammers p.c.c 1:3:6 for an average thickness 40 to 50 mm using approved quality 20 mm and down size graded broken granite stone aggregates, approved quality river sand and portland cement of approved make, as screed layer in flooring. the surface of the screed laid as above shall be made rough using wire brushes or brooms. the work shall include necessary curing, disposing off and carting away the debris from the banks premises etc all complete as directed by the banks engineer quote rate per unit exclusive of gst preparing the surface of the screed concrete layer / floor slab by thorough cleaning and priming with cement slurry to receive the new flooring, providing and laying flooring in the approved pattern, line level etc., using 600 mm x 600 mm or approved size polished vitrified tiles of approved make and shade over a bed of cement mortar prepared by hand mixing approved make portland cement and approved quality river sand in the ratio 1: 4, laid, spread and consolidated to get an average consolidated thickness of 20 mm. the tiles shall be set with a floating layer of grey cement slurry and joints shall be pointed with tile grouts of approved make and quality to match with the shade of the tile. refer tender document for detailed description quote rate per unit exclusive of gst preparing the surface of the walls to receive the new skirting by watering and cleaning, providing and fixing 100 mm height skirting cut out of 600 x 600 mm or approved size fully vitrified tiles of approved make and shade over a backing of cm 1: 4 ( using approved quality river sand and opc ) for the required thickness, true to plumb and line, set with grey cement paste and joint pointed with tile grouts of approved make and quality to match with the shade of the tile. the rate shall include machine grinding and buffing of the exposed edges / sharp corners, machine cutting, curing, cleaning of the finished work, all leads & lifts, etc required for the finished work all as directed by the banks engineer. refer tender document for detailed description quote rate per unit exclusive of gst providing and fixing 1st quality / premium quality ceramic glazed tiles of size 300mm x 450mm ( or approved nearest available size ) and of approved shade and make, for wall dado over the plastered and bordered surface as per item no: 08 with 6 mm average thick back mortar of c. m 1:3 ( 1 cement : 3 fine river sand ) and set with cement paste spread fully over the whole back area of the tile the work is liable to be summarily rejected if the joint is found susceptible to hollowness ) and also including pointing the joints with tile grout of matching shade, curing, etc. all complete as directed by the bank?s engineer. the rate shall include for all cutting, grinding the exposed edges, pvc beading on exterior corners, wastage, proper finishing, using different shades of tiles if any in the dado etc. refer tender document for detailed description quote rate per unit exclusive of gst carefully dismantling and removing the existing door frames with shutters in bath & toilets, including finishing the wall surfaces properly and neatly as required using cement mortar 1:3 of required thickness, providing and fixing minimum 24mm thick approved brand pvc door shutter in approved shade and design including door frame of suitable sections with required length as per site conditions shade and design including door frame of suitable sections with required length as per site conditions etc. rate shall be inclusive of fixing 3nos of 100 x 25mm aluminium butt hinges, pvc door handles on both the sides, one number 100mm pvc tower bolt to each side of the door shutters, carting away the debris if any etc. all as directed by the banks engineer. necessary rebate towards salvage value of removed wooden door with shutter shall be considered while quoting the rate for the item quote rate per unit exclusive of gst carefully dismantling and removing the existing wooden ventilator and finishing the opening, providing and fixing new ventilator of approx. size 750 mm x 1050 mm made with upvc frames of suitable sections and louver panels using 5 mm thick frosted glass fixed to the frame using upvc cleats and beading, all complete as directed by the bank?s engineer. all the corners and joints of the frame & sash shall be mitred cut & fusion welded without any mechanical joint.quote rate per unit exclusive of gst all same as item 10 above but for the ventilator in wash basin area of approx. size ???..with openable single shutter and additional ms grill for safety purpose all complete as directed by the banks engineerquote rate per unit exclusive of gst repairs to under deck ceiling: carefully dismantling and removing the damaged portion of pop sheets / frame work in under deck ceiling at various locations, repairs to the existing ceiling frame work, supplying and fixing additional frame work / glass wool panels wherever necessary, providing and fixing plain gypsum board of 12.5mm thickness fixed to the suspended grid in approved methods , the joints shall be finished with joint paper tape and jointing compound of approved make and providing and applying plaster of paris putty for required thickness. the surface of the false ceiling fixed as above shall be prepared by sand papering, providing, applying and finishing a coat of approved make white cement putty, one coat of approved make cement primer etc. including removal of debris all complete as directed by the banks engineer quote rate per unit exclusive of gst carefully chipping and removing the loosen / spallen concrete / plastering etc. to expose sound / hard concrete / masonry work etc, thoroughly cleaned with wire brush etc. complete. a ) plastering to nonstructural members: providing and rendering cement plaster of 25 mm or above average thickness in patches in c.m. 1:4 ( 01 port land cement: 04 river sand ) ) mixed with nitobond sbr as per manufacturers specifications true to plumb and line to match with the adjoining plastering in different layers and finishing the same smoothly and neatly etc. b ) repairs to structural members: preparation of surface, providing and applying anticorrosive epoxy chemical / acrylic bonding agent of approved make ( products from m / s fosroc or approved equivalent ) to reinforcement and concrete surfaces, then surfaces shall be plastered and finished with polymer modified mortar with cm 1:3 mixed with approved brand chemicals.refer tender document for detailed descriptionquote rate per unit exclusive of gst repainting the entire interior area of flat by preparing the surface of the walls, ceiling and soffits or vertical sides of the beams, wood and metal surfaces, etc by scrapping, sand papering & dusting of loose paints / paint flakes etc, providing and applying: two coats of white wash with shell lime / obd to ceiling etc. refer tender document for detailed description quote rate per unit exclusive of gst providing and fixing mosquito net of ?saint gobain? or approved equivalent of approved colour and design on wooden windows / ventilators frame work with the help of velcro. the fixing of velcro on wooden frame shall be carried out by staple gun. the rate shall also include folding the net ( approx. 25mm ) on all cut edges ( four sides ) and stitching complete, disposal of old netlon meshes out of the premises etc. as directed by the bank?s engineers. ( folded part of netlon shall not be measured for payment ) quote rate per unit exclusive of gst...

Tamil Nadu Cooperative Sugar Federation Limited - Tamil Nadu

27708969 septic tank cleaning work and toilet plumbing and carpentry work septic tank cleaning work and ladies toilet plumbing and carpentry work , administrative building ladies bathroom renovation work , septic tank sewage water removing for one load cost is rs . 3000 ( 3000 litter capacity vehicle ) , dia of soak pit 4 feet depth of soak pit 6 feet material & manpower cost details: concrete ring 4 feet dia and 1 feet height 6 nos with manhole cover , inside filling material 70 cft / broken brick aggregate / 40mm size gravel , manpower for erection of concrete ring , pvc door , pillar cock , angle cock , mirror 3 x 2 , plastic accssories , fixing labour work , wash basin , white wash two coat...

Military Engineer Services - Tamil Nadu

26699058 periodical services to certain buildings at airforce station thanjavur . , material and labour for preparing plastered or unplasterd old decorated wall surfaces including cornices , pillars etc and applying one coat of white wash on wall complete all as specified and as directed . , material and labour for preparing plastered or unplasterd old decorated ceiling surfaces and applying one coat of white wash on ceiling complete all as specified and as directed . , material and labour for preparation of old decorated wall surfaces and applying one coat of distemper oil emulsion on walls complete all as specified and as directed . , material and labour for preparation of old decorated surfaces of walls and applying one coat of cement based paint on wall ( external borders is required dark blue or existing colour ) all as specified and as directed . note: painting to bldgs nos also including in this item . , material and labour for preparation of old painted wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed . , material and labour for preparation of old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed . , taking down cement plaster of any description , raking out joints , hacking for keys and washing down with water etc complete all as specified and directed . , material and labour for rendering 15mm thick in cm 1:4 on fair faces of brick or concrete work making surfaces even and smooth without using extra cement and applying two coats of white wash after preparing newly plastered surfaces complete all as specified and directed . , material and labour for preparing new plastered surface of walls and applying two coats of white wash all as specified and as directed . , material and labour for preparation of old painted ( brick , stone , concrete , asbestos cement or plaster ) surfaces of any description applying one coat of acrylic exterior emulsion paint on walls all as specified and directed . , material and labour for preparing plastered or unplasterd old decorated wall surfaces including cornices , pillars etc and applying one coat of colour wash on wall complete all as specified and as directed ....

Military Engineer Services - Tamil Nadu

26613912 painting/marking of runway in tech area at air force station thanjavur . , material and labour for applying polymer modified emulsion on existing water based road marking painted surfaces over flexible pavements for obliterating the existing unwanted runway marking to any width or girth all as specified and as directed . , material and labour for applying water based paints on existing water based road marking painted surfaces over rigid pavements for for obliterating the existing unwanted runway marking any width or girth all as specified and as directed . , material and labour for applying one coat of water based road marking paint in as lines , dashes , arrows , letters , boxes etc on roads , pavements and the like including preparation of old surfaces exceeding 10cm wide all as specified and as directed . , all as per sl item no . 3 here in before but not exceeding 10cm wide , all as per sl item no . 3 here in before but not exceeding 5cm wide , material and labour for applying two coats of painting with water based road marking paint white or golden yellow such as lines , dashes , arrows , letters etc on roads , pavement and the like exceeding 10cm wide . , material and labour for applying one coat of white wash in concrete pavement surface including preparation of old surfaces all as specified and as directed . note: white wash shall be carried out at an interval as required by air force authorities at runway 07 & 25 and each coat shall be paid seperately . , material and labour for applying one coat of synthetic enamel paint on walls surfaces including preparation of old surfaces of any description over 10 cm in width or girth not otherwise described . , material and labour for applying one coat of synthetic enamel paint on concrete surfaces including preparation of old surfaces of any description not exceeding 10 cm in width or girth . , material and labour for applying one coat of synthetic enamel paint on concrete surfaces including preparation of old surfaces of any description not exceeding 05 cm in width or girth . ...

Khadi And Village Industries Commission - Tamil Nadu

24819497 tender for registered contractors for construction of group work shed for khadi artisans by avarampalayam sarvodaya sangh at kamatchipuram, ondipudur, coimbatore under the “work shed scheme for khadi artisans” implemented by khadi and village industries commission 1. earth work excavation in all sub soils for foundation. 2. r.r.masonry in cm 1.8 for foundation and flooring a.foundation flooring: all walls of the building 1920.00 b.basement footing: all walls if the building 576.00 3. floor finishing in cm1.5 hall 4. p.c.c.1:5:10 mix for foundation and 40mm h.b.g metal including laying, consolidation, curing complete etc.. floor area 5. sand filling inside the basement for pallam sand floor area 6. hollow block full mould in cm 1:5 for supper structure all walls of the building 7. wall plastering in cm1.5 for supper structure in side hall 2664.00 out side hall 3192.00 8. preparing and fixing of steel frames and glazed shutters of doors and windows including all necessary fittings etc. 9. supplying and fixing of calvelium sheet with m.s.truss and ” l”angle purline including necessary “j” bolts,nuts, washers and all necessary fittings etc.., all walls of the building amenities 10 water supply arrangements 11. electrical installations 12. white wash two coats ...

Tamil Nadu Cooperative Sugar Federation Limited - Tamil Nadu

24574466 supply of rubber joint . , 1 / 8 rubber joint ( 1 mm width ) , emmary roll 4 width ( rough ) , emmary roll 4 width ( smpooth ) , m seal 75 mg pack , m seal pvc 50 mg pack , solvent cement ( 250 ml ) , 4 white wash brush , broom sticee , masala rope , concsete nails 2 , nail washer , 3 blacee hose claup , 2 1 / 2 blacee hose claup , 2 1 / 2 blacee hose nipple joint , hand haxsaew blade...

Rural Development And Panchayats Department - Tamil Nadu

24103942 package no . 05/2019 20 yercaud block no . of works 03 construction 2 class room and girls toilet building in salem district ( rcsids ) 2019 20 , 1 . ) construction of 2 class room for pum school building at mellur h/o vellakadai , earth work excavation and depositing on bank with initial lead and lift in hard gravelly soil as per ss20 b for foundation etc , complete , cement concrete in 1 : 4 : 8 mix using 40 mm metal including cost and conveyance of all materials to site and labour charges etc complete , random rubble masonry in cement mortar 1 : 5 mix using new rough stones with symultaneous pointing including cost and conveyance of all materials to site and labour charges etc complete . , filling with collected sand as per standard specifications etc complete , refilling with excavated earth as per standard specifications etc complete , brick work in cement mortor 1:5 ( one cement and five sand ) using country bricks of size 23 x 11 . 5 x 7 . 5 cms for the following including mixing mortar and all other labour charges etc complete . , super structure , supplying and errecting shuttering including necessary support for plane surface in foundation basement and roof slabs strutting upto 3 . 29 m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations grade beams , raft slabs stair case steps , bed blocks , critical pier , etc beams roof slabs , using mild steelsheets of size 90 x 60 cm and 10 gouge stiffened , welded with steel angles of size 25 mm x 25 mm x 3mm for boarding laid over silver oak ( country wood ) joists of 10 cm size x 6 . 5 cms size spaced at about 90 cms center to center and supported causorina props of 10 cm to 13 cms spaced at 75 cms to center to center etc . , complete complying with standard specification and as directed ( si 155 ) for column footing and plinth beam , do . . for column and sunshade , do . . for slab and beam , kdo . . for sides , r . c . c . 1:1 . 5:3 using 20mm iss hbgs metal including cost and conveyance of materials and labour charges etc . complete , supplying , fabricating and placing in position inild steel or ribbed tor steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc complete complying with standard ( ms rods or rts rods ) which will be supplied departmentally at section stores and cost will be recovered at issue rate . the binding wire shall be supplied by the contractor . , weathering course with brick jelly lime concrete in the proportion of 32:12 . 5 by volume including cost and conveyance of all and labour charges etc . complete . , floor finishing with granolithic cement concrete 1:2:4 to a thickness of 25 mm ( one cement , two sand and four broken granite metal ) using 10 to 12 mm iss broken hard granite metal including watering whenever necessary and paid in lay not more than 15 cm compacting etc . , complete complying with standard specification . , supply of steel doors and windows including cost and convyance and all charges etc complete . etc complete steel door ( 1 . 20x2 . 10m ) , window w ( 1 . 20x1 . 30m ) , window w1 ( 1 . 20x1 . 30m ) , plastering with c . m 1:5 mix , 12 mm thick including cost and conveyance of all materials to site and labour charges etc complete . , finishing the exposed surface of rcc item of work such as slabs , beams , sunshade , facia , canopy slab , staircase waist slab , landing slab etc . , with cm 1:3 , 10mm thick . including raking the surface . the rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps , landing slabs etc . , complete complying with standard specifications . , painting two coats over new iron work using synthetic enamal paint including cost and conveyance of all materials to site etc complete , oil distempering two coats over plastering surface including cost and conveyance of materials and labour charges etc complete , white wash two coat using shell lime including cost and conveyance of materials and labour charges etc complete , cement painting two coats with approved cement paint over cement plastered surface including cost and conveyance of materials and labour charges etc complete . , black board painting two coats using black oxide for new blackboard including cost and conveyance of paint and all labour charges etc complete , providing and fixing of pvc rain water down fall pipe 110mm dia with necessary t w clamps , plug , shoes , bend , screws , nails etc . , complete , supply and fixing of cadapah slab of 20/30mm thick including cost and conveyance and all charges etc comp , ete . , providing rain water harvesting structure etc , complete , 2 . ) construction of girls toilet in pue school at mellur h/o vellakadai , earth work excavation for foundation of structures up to 3m depth as per drawing and technical specification clause 1104 including setting out , construction of shoring and bracing , removal of stumps and other deleterious matter , dressing of sides and bottom and back filling with approved material . , cement concrete 1 : 4 : 8 mix using 40mm hbg metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick . , compacting etc . , complete complying with standard specifications and as directed for foundation , random rubble masonry in cement mortar 1 : 5 mix using new rough stones with symultaneous pointing including cost and conveyance of all materials to site and labour charges etc complete . , filling with collected sand as per standard specifications etc complete , brick work in cement mortor 1:5 ( one cement and five sand ) using country bricks of size 23 x 11 . 5 x 7 . 5 cms for the following including mixing mortar and all other labour charges etc complete . , supplying and errecting shuttering including necessary support for plane surface in foundation basement and roof slabs strutting upto 3 . 29 m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations grade beams , raft slabs stair case steps , bed blocks , critical pier , etc beams roof slabs , using mild steelsheets of size 90 x 60 cm and 10 gouge stiffened , welded with steel angles of size 25 mm x 25 mm x 3mm for boarding laid over silver oak ( country wood ) joists of 10 cm size x 6 . 5 cms size spaced at about 90 cms center to center and supported causorina props of 10 cm to 13 cms spaced at 75 cms to center to center etc . , complete complying with standard specification and as directed ( si 155 ) for column footing and plinth beam , side , supplying , fabricating and placing in position inild steel or ribbed tor steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc complete complying with standard ( ms rods or rts rods ) which will be supplied departmentally at section stores and cost will be recovered at issue rate . the binding wire shall be supplied by the contractor . , r . c . c . 1:1 . 5:3 using 20mm iss hbgs metal including cost and conveyance of materials and labour charges etc . complete , finishing the exposed surface of rcc item of work such as slabs , beams , sunshade , facia , canopy slab , staircase waist slab , landing slab etc . , with cm 1:3 , 10mm thick . including raking the surface . the rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps , landing slabs etc . , complete complying with standard specifications . , plastering with c . m 1:5 mix , 12 mm thick including cost and conveyance of all materials to site and labour charges etc complete . , paving the flooring with special type of flooring tiles ( cement based hydraulically pressed anti...

Rural Development And Panchayats Department - Tamil Nadu

24103941 package no . 10/2019 20 kolathur block no . of works 01 construction 2 class room building in salem district ( rcsids ) 2019 20 , 1 . ) construction of 2 class room for pue school building at kottamedu h/o singripatty , earth work excavation and depositing on bank with initial lead and lift in hard gravelly soil as per ss20 b for foundation etc , complete , cement concrete in 1 : 4 : 8 mix using 40 mm metal including cost and conveyance of all materials to site and labour charges etc complete , random rubble masonry in cement mortar 1 : 5 mix using new rough stones with symultaneous pointing including cost and conveyance of all materials to site and labour charges etc complete . , filling with collected sand as per standard specifications etc complete , refilling with excavated earth as per standard specifications etc complete , brick work in cement mortor 1:5 ( one cement and five sand ) using country bricks of size 23 x 11 . 5 x 7 . 5 cms for the following including mixing mortar and all other labour charges etc complete . , super structure , supplying and errecting shuttering including necessary support for plane surface in foundation basement and roof slabs strutting upto 3 . 29 m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations grade beams , raft slabs stair case steps , bed blocks , critical pier , etc beams roof slabs , using mild steelsheets of size 90 x 60 cm and 10 gouge stiffened , welded with steel angles of size 25 mm x 25 mm x 3mm for boarding laid over silver oak ( country wood ) joists of 10 cm size x 6 . 5 cms size spaced at about 90 cms center to center and supported causorina props of 10 cm to 13 cms spaced at 75 cms to center to center etc . , complete complying with standard specification and as directed ( si 155 ) for column footing and plinth beam , do . . for column and sunshade , do . . for slab and beam , kdo . . for sides , r . c . c . 1:1 . 5:3 using 20mm iss hbgs metal including cost and conveyance of materials and labour charges etc . complete , supplying , fabricating and placing in position inild steel or ribbed tor steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc complete complying with standard ( ms rods or rts rods ) which will be supplied departmentally at section stores and cost will be recovered at issue rate . the binding wire shall be supplied by the contractor . , weathering course with brick jelly lime concrete in the proportion of 32:12 . 5 by volume including cost and conveyance of all and labour charges etc . complete . , finishing the top of roof with one course of pressed tiles of size 20 x 20 x 2 mm laid in cm 1:3 12 mm thick mixes with w . p . compound laid 2 % weight of cement etc . , complete . , floor finishing with granolithic cement concrete 1:2:4 to a thickness of 25 mm ( one cement , two sand and four broken granite metal ) using 10 to 12 mm iss broken hard granite metal including watering whenever necessary and paid in lay not more than 15 cm compacting etc . , complete complying with standard specification . , paving the floor with scratch proof ceromic tiles of size 305x305x6mm including cost and conveyance of all materials to site and all labour charges etc complete , supply of steel doors and windows including cost and convyance and all charges etc complete . etc complete steel door ( 1 . 20x2 . 10m ) , window w ( 1 . 20x1 . 30m ) , window w1 ( 1 . 20x1 . 30m ) , plastering with c . m 1:5 mix , 12 mm thick including cost and conveyance of all materials to site and labour charges etc complete . , finishing the exposed surface of rcc item of work such as slabs , beams , sunshade , facia , canopy slab , staircase waist slab , landing slab etc . , with cm 1:3 , 10mm thick . including raking the surface . the rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps , landing slabs etc . , complete complying with standard specifications . , painting two coats over new iron work using synthetic enamal paint including cost and conveyance of all materials to site etc complete , oil distempering two coats over plastering surface including cost and conveyance of materials and labour charges etc complete , white wash two coat using shell lime including cost and conveyance of materials and labour charges etc complete , cement painting two coats with approved cement paint over cement plastered surface including cost and conveyance of materials and labour charges etc complete . , black board painting two coats using black oxide for new blackboard including cost and conveyance of paint and all labour charges etc complete , providing and fixing of pvc rain water down fall pipe 110mm dia with necessary t w clamps , plug , shoes , bend , screws , nails etc . , complete , supply and fixing of cadapah slab of 20/30mm thick including cost and conveyance and all charges etc comp , ete . , wiring with 2 x 1 . 5 sq . mm ( 22 / 0 . 3 ) pvc insulated sc unsheathed copper conducutor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 3 mm thick hylum sheet cover with tw box and 5 a ft switch with continuous earth connection of 14 swg tc wire for making good of the concealed portion with suitable colour for pvc concealed light point / fan point ( for electronic regulator ) sd 24 , wiring with 2 x 1 . 5 sq . mm ( 22 / 0 . 3 ) pvc insulated sc unsheathed copper conducutor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 150 mm x 100 mm x 113 mm tw switch box with 3 mm thick hylum sheet cover for 5 a 3 pin non interlocking cs plug with continuous earth wire connection of 14 swg tc wire for making good of the concealed portion with suitable colour for concealed pvc plug point sd 38 , supply and run of 2 of 4sq . mm ( 22/0 . 30 ) pvc insulated sc unsheathed copper conductor of 1100 v grade on 7/20gi bearer wire for service connection mains sd 65 , supply and run of 2 x4 sq . mm ( 22 / 0 . 30 ) pvc insulated sc unsheathed copper conductor of 1100 v grade in 25 mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains . sd 70 , supply and fixing of wt bulk head fitting with guard ( philips / bajaj / crompton / k lite ) suitable for incandescent lamp with 60 w bulb . sd 83 , supply and fixing of 16 amps dpic switch of 500 v with fuse and neutral ( side handle ) on suitable tw box pwd earthing sd 141 , supply and fixing of single box type 4 40w flourescent tube fitting with copper choke and condenser with tw round block on wall or ceiling with flourescent tube with pvc unsheathed copper leads from terminals to the fitting of tube light [sd 88 ] , supply and fixing of 1200 mm ( 48 ) ac ceiling fan complete with stepped electronic 300 w regulator with 300 mm down rod on the existing clamp . sd 106 , providing fire extingusher etc , complete , providing rain water harvesting structure etc , complete , gst amount for providing service to government contract works for the above construction works . { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package}...

Rural Development And Panchayats Department - Tamil Nadu

24103937 package no . 19/2019 20 veerapandi block no . of works 02 construction of 2 class room and girls buildings in salem district ( rcsids ) 2019 20 , 1 . ) construction of 2 class room for pum school building at puthur agraharam h/o puthur agraharam , earth work excavation and depositing on bank with initial lead and lift in hard gravelly soil as per ss20 b for foundation etc , complete , cement concrete in 1 : 4 : 8 mix using 40 mm metal including cost and conveyance of all materials to site and labour charges etc complete , random rubble masonry in cement mortar 1 : 5 mix using new rough stones with symultaneous pointing including cost and conveyance of all materials to site and labour charges etc complete . , filling with collected sand as per standard specifications etc complete , refilling with excavated earth as per standard specifications etc complete , brick work in cement mortor 1:5 ( one cement and five sand ) using country bricks of size 23 x 11 . 5 x 7 . 5 cms for the following including mixing mortar and all other labour charges etc complete . , super structure , supplying and errecting shuttering including necessary support for plane surface in foundation basement and roof slabs strutting upto 3 . 29 m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations grade beams , raft slabs stair case steps , bed blocks , critical pier , etc beams roof slabs , using mild steelsheets of size 90 x 60 cm and 10 gouge stiffened , welded with steel angles of size 25 mm x 25 mm x 3mm for boarding laid over silver oak ( country wood ) joists of 10 cm size x 6 . 5 cms size spaced at about 90 cms center to center and supported causorina props of 10 cm to 13 cms spaced at 75 cms to center to center etc . , complete complying with standard specification and as directed ( si 155 ) for column footing and plinth beam , do . . for column and sunshade , do . . for slab and beam , kdo . . for sides , r . c . c . 1:1 . 5:3 using 20mm iss hbgs metal including cost and conveyance of materials and labour charges etc . complete , supplying , fabricating and placing in position inild steel or ribbed tor steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc complete complying with standard ( ms rods or rts rods ) which will be supplied departmentally at section stores and cost will be recovered at issue rate . the binding wire shall be supplied by the contractor . , weathering course with brick jelly lime concrete in the proportion of 32:12 . 5 by volume including cost and conveyance of all and labour charges etc . complete . , finishing the top of roof with one course of pressed tiles of size 20 x 20 x 2 mm laid in cm 1:3 12 mm thick mixes with w . p . compound laid 2 % weight of cement etc . , complete . , floor finishing with granolithic cement concrete 1:2:4 to a thickness of 25 mm ( one cement , two sand and four broken granite metal ) using 10 to 12 mm iss broken hard granite metal including watering whenever necessary and paid in lay not more than 15 cm compacting etc . , complete complying with standard specification . , paving the floor with scratch proof ceromic tiles of size 305x305x6mm including cost and conveyance of all materials to site and all labour charges etc complete , supply of steel doors and windows including cost and convyance and all charges etc complete . etc complete steel door ( 1 . 20x2 . 10m ) , window w ( 1 . 20x1 . 30m ) , window w1 ( 1 . 20x1 . 30m ) , plastering with c . m 1:5 mix , 12 mm thick including cost and conveyance of all materials to site and labour charges etc complete . , finishing the exposed surface of rcc item of work such as slabs , beams , sunshade , facia , canopy slab , staircase waist slab , landing slab etc . , with cm 1:3 , 10mm thick . including raking the surface . the rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps , landing slabs etc . , complete complying with standard specifications . , painting two coats over new iron work using synthetic enamal paint including cost and conveyance of all materials to site etc complete , oil distempering two coats over plastering surface including cost and conveyance of materials and labour charges etc complete , white wash two coat using shell lime including cost and conveyance of materials and labour charges etc complete , cement painting two coats with approved cement paint over cement plastered surface including cost and conveyance of materials and labour charges etc complete . , black board painting two coats using black oxide for new blackboard including cost and conveyance of paint and all labour charges etc complete , providing and fixing of pvc rain water down fall pipe 110mm dia with necessary t w clamps , plug , shoes , bend , screws , nails etc . , complete , supply and fixing of cadapah slab of 20/30mm thick including cost and conveyance and all charges etc comp , ete . , wiring with 2 x 1 . 5 sq . mm ( 22 / 0 . 3 ) pvc insulated sc unsheathed copper conducutor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 3 mm thick hylum sheet cover with tw box and 5 a ft switch with continuous earth connection of 14 swg tc wire for making good of the concealed portion with suitable colour for pvc concealed light point / fan point ( for electronic regulator ) sd 24 , wiring with 2 x 1 . 5 sq . mm ( 22 / 0 . 3 ) pvc insulated sc unsheathed copper conducutor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 150 mm x 100 mm x 113 mm tw switch box with 3 mm thick hylum sheet cover for 5 a 3 pin non interlocking cs plug with continuous earth wire connection of 14 swg tc wire for making good of the concealed portion with suitable colour for concealed pvc plug point sd 38 , supply and run of 2 of 4sq . mm ( 22/0 . 30 ) pvc insulated sc unsheathed copper conductor of 1100 v grade on 7/20gi bearer wire for service connection mains sd 65 , supply and run of 2 x4 sq . mm ( 22 / 0 . 30 ) pvc insulated sc unsheathed copper conductor of 1100 v grade in 25 mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains . sd 70 , supply and fixing of wt bulk head fitting with guard ( philips / bajaj / crompton / k lite ) suitable for incandescent lamp with 60 w bulb . sd 83 , supply and fixing of 16 amps dpic switch of 500 v with fuse and neutral ( side handle ) on suitable tw box pwd earthing sd 141 , supply and fixing of single box type 4 40w flourescent tube fitting with copper choke and condenser with tw round block on wall or ceiling with flourescent tube with pvc unsheathed copper leads from terminals to the fitting of tube light [sd 88 ] , supply and fixing of 1200 mm ( 48 ) ac ceiling fan complete with stepped electronic 300 w regulator with 300 mm down rod on the existing clamp . sd 106 , providing fire extingusher etc , complete , providing rain water harvesting structure etc , complete , 2 . ) construction of girls toilet in pum school at puthur agraharam h/o puthur agraharam , earth work excavation for foundation of structures up to 3m depth as per drawing and technical specification clause 1104 including setting out , construction of shoring and bracing , removal of stumps and other deleterious matter , dressing of sides and bottom and back filling with approved material . , cement concrete 1 : 4 : 8 mix using 40mm hbg metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick . , compacting etc . , complete complying with standard specifications and a...

V O Chidambaranar Port Trust - Tamil Nadu

24055710 annual cleaning the toilets , drainages , water tank , maintenance of garden and distribution of water to all office building and cpt bungalow at zone b for one year , cleaning the toilets , drainage system , mopping the entire floor area and maintaining the garden in the following buildings & wherever required in zone b area viz . , dry dock , fire service , first aid centre , cisf cabin , maintenance office , atm office , vhp station , electrical sub division , weigh bridge , cpts bungalow by engaging 4 nos . of mazdoor ( male ) including sunday & holiday in specified uniform . the cost including labour , uniform , cleaning materials such as short brooms 6 nos . , long brooms 6 nos . , harpic 500ml . 6 nos , air freshner 500ml . 3 nos , floor cleaner 500ml . 3 nos , nabthalin ball 1 kg , brushes , buckets , etc . , complete and as directed by the departmental officers . ( recovery will made as per conditions of the schedule , if any of the mazdoor ( male ) found absent . ) , cleaning the main gate & surrounding area , maintenance sub division office , camp office , cpt bungalow and other works at zone b by engaging 9 nos . of mazdoor ( female ) including sunday & holiday in specified uniform . the cost including labour , uniform , cleaning materials such as short brooms 6 nos . , long brooms 6 nos . , harpic 500ml . 6 nos . , air freshner 500ml . 3 nos . , floor cleaner 500ml . 3 nos . , nabthalin ball 1 kg . , brushes , buckets etc . , complete and as directed by the departmental officers . ( recovery will made as per conditions of the schedule , if any of the mazdoor ( female ) found absent ) . , engaging of valve operator 2 nos . having 10th standard pass iti in any trade with one year experience for distribution of water to office buildings , call point and cpt bungalow and collection of water from corporation & port truck supply . the cost including wages , tools & plants etc . , complete and as directed by the departmental officers . ( recovery will made as per condition of the schedule , if any of the valve operator is found absent ) . , engaging of tractor with men , tools & plants for loading the segregated bio degradable and bio non degradable garbage into tractors as per requirement from zone b harbour area , port dispensary complex , port community centre at zone b & cpt bungalow and conveying the same to zone b maintenance sub division for log book entry and conveying to port garbage disposal site . on environmental point of view , every tractor load should be covered and tied with tarpaulin to avoid spillage on road . the cost inclusive of t & p , labour , hire charge for tractor , fuel charges and all other miscellaneous expenditure etc . , to execute the work and complete the work to the entire satisfaction of the departmental officers . ( recovery will be made based on the condition of the schedule if the tractor is not deployed to execute the work ) . , providing 1 no . carpenter iind class ( semi skilled category ) for attending repair works in all wooden works such as doors , windows , ventilators , etc . , in all the buildings in port premises @ zone b area in all working days excluding sundays & holidays including necessary tools & plants etc . , . all required fixtures will be supplied by department etc . , complete and as directed by the departmental officers . ( recovery will made as per condition of the schedule , if the carpenter is found absent ) . , cleaning the ground level reservoir ( glr ) @ zone b area ( south glr 1 , 00 , 000 litre capacity ) using required man power , tools & plants for removing the water tank cover slab and refixing the same in position . the cost including dewatering the tank using pump , cleaning materials like bleaching powder , washing soda , broom sticks and all other tools & plants , one coat of white wash in the interior walls of glr using shell lime etc . , complete to the satisfaction and as directed by the departmental officers . note :cleaning of the said water tanks should be done at an interval of six months . , cleaning the over head water tanks at zone b area viz . , 1 ) cpt bungalow 12 nos . , b ) port dispensary 3 nos . , c ) atm office 1 no . , d ) call point & water point 2 nos . , e ) cisf & customs office 1 no . , f ) electrical sub division office 1 no . , g ) intuc union office 1 no . , h ) hms union office 1 no . , i ) petu union office 1 no . , j ) anna dock union office 1 no . , k ) medical 1 no . , l ) hms ( workers ) union office 1 no . , m ) officers association office 1 no . , n ) drinking point at zone b 1 no . , by engaging cleaning labour , inlcuding cost of labour , cleaning materials such as brooms , brushes , bleaching powder etc . , complete and as directed by the departmental officers . ( water tanks to be cleaned once in a month interval or whenever required ) ...

V O Chidambaranar Port Trust - Tamil Nadu

23897976 annual cleaning the toilets , drainages , water tank , maintenance of garden and distribution of water to all office building and cpt bungalow at zone b for one year annual cleaning the toilets , drainages , water tank , maintenance of garden and distribution of water to all office building and cpt bungalow at zone b for one year , cleaning the toilets , drainage system , mopping the entire floor area and maintaining the garden in the following buildings & wherever required in zone b area viz . , dry dock , fire service , first aid centre , cisf cabin , maintenance office , atm office , vhp station , electrical sub division , weigh bridge , cpts bungalow by engaging 4 nos . of mazdoor ( male ) including sunday & holiday in specified uniform . the cost including labour , uniform , cleaning materials such as short brooms 6 nos . , long brooms 6 nos . , harpic 500ml . 6 nos , air freshner 500ml . 3 nos , floor cleaner 500ml . 3 nos , nabthalin ball 1 kg , brushes , buckets , etc . , complete and as directed by the departmental officers . ( recovery will made as per conditions of the schedule , if any of the mazdoor ( male ) found absent . ) , cleaning the main gate & surrounding area , maintenance sub division office , camp office , cpt bungalow and other works at zone b by engaging 9 nos . of mazdoor ( female ) including sunday & holiday in specified uniform . the cost including labour , uniform , cleaning materials such as short brooms 6 nos . , long brooms 6 nos . , harpic 500ml . 6 nos . , air freshner 500ml . 3 nos . , floor cleaner 500ml . 3 nos . , nabthalin ball 1 kg . , brushes , buckets etc . , complete and as directed by the departmental officers . ( recovery will made as per conditions of the schedule , if any of the mazdoor ( female ) found absent ) . , engaging of valve operator 2 nos . having 10th standard pass iti in any trade with one year experience for distribution of water to office buildings , call point and cpt bungalow and collection of water from corporation & port truck supply . the cost including wages , tools & plants etc . , complete and as directed by the departmental officers . ( recovery will made as per condition of the schedule , if any of the valve operator is found absent ) . , engaging of tractor with men , tools & plants for loading the segregated bio degradable and bio non degradable garbage into tractors as per requirement from zone b harbour area , port dispensary complex , port community centre at zone b & cpt bungalow and conveying the same to zone b maintenance sub division for log book entry and conveying to port garbage disposal site . on environmental point of view , every tractor load should be covered and tied with tarpaulin to avoid spillage on road . the cost inclusive of t & p , labour , hire charge for tractor , fuel charges and all other miscellaneous expenditure etc . , to execute the work and complete the work to the entire satisfaction of the departmental officers . ( recovery will be made based on the condition of the schedule if the tractor is not deployed to execute the work ) . , providing 1 no . carpenter iind class ( semi skilled category ) for attending repair works in all wooden works such as doors , windows , ventilators , etc . , in all the buildings in port premises @ zone b area in all working days excluding sundays & holidays including necessary tools & plants etc . , . all required fixtures will be supplied by department etc . , complete and as directed by the departmental officers . ( recovery will made as per condition of the schedule , if the carpenter is found absent ) . , cleaning the ground level reservoir ( glr ) @ zone b area ( south glr 1 , 00 , 000 litre capacity ) using required man power , tools & plants for removing the water tank cover slab and refixing the same in position . the cost including dewatering the tank using pump , cleaning materials like bleaching powder , washing soda , broom sticks and all other tools & plants , one coat of white wash in the interior walls of glr using shell lime etc . , complete to the satisfaction and as directed by the departmental officers . note :cleaning of the said water tanks should be done at an interval of six months . , cleaning the over head water tanks at zone b area viz . , 1 ) cpt bungalow 12 nos . , b ) port dispensary 3 nos . , c ) atm office 1 no . , d ) call point & water point 2 nos . , e ) cisf & customs office 1 no . , f ) electrical sub division office 1 no . , g ) intuc union office 1 no . , h ) hms union office 1 no . , i ) petu union office 1 no . , j ) anna dock union office 1 no . , k ) medical 1 no . , l ) hms ( workers ) union office 1 no . , m ) officers association office 1 no . , n ) drinking point at zone b 1 no . , by engaging cleaning labour , inlcuding cost of labour , cleaning materials such as brooms , brushes , bleaching powder etc . , complete and as directed by the departmental officers . ( water tanks to be cleaned once in a month interval or whenever required ) ...

Military Engineer Services - Tamil Nadu

21937924 tender for as and as to ward room annexe ( building no p 216 ) at ins rajali arakkonam 1 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) complete all as specified and as directed by engr in charge. 2 demolition of cement concrete in ground floors and pavings not exc 15 cm thickness but above ground floors complete all as specified and as directed by engr in charge. 3 material and labour for 25mm thick pcc 1:2:4 type b1 ( using 12.5mm graded stone aggregate ) as in sub base to flooring complete all as specified and as directed by engr in charge. 4 material and labour for light shade vitrified ceramic tiles 10mm thick ( square / rectangular ) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors / etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles including screed bed 15mm thick in cement mortar 1:4 etc., complete all as specified and as directed by engr in charge. 5 all as per item no. 04 here in before but in skirting with 10mm thick in cement mortar 1:3 etc., complete all as specified and as directed by engr in charge. 6 material and labour for coloured non skid ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc., over 15mm thick screed bed in cement mortar 1:4 set set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and as directed by engr in charge. 7 material and labour for coloured glazed ceramic tiles in vertical surface 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick back coat in cm 1:3 complete all as specified and as directed by engr in charge. 8 taking down steel windows of any description with frames including guard bars ( glazed window, flyproof window and guard bars ) area not exc 1 sqm each and making good the disturbed plastered surfaces with 10mm plaster in cm 1:6 and final finish as per existing complete all as specified and as directed by engr in charge. 9 taking down steel windows of any description with frames including guard bars ( glazed window, flyproof window and guard bars ) area exc 1 sqm but not exc 2 sqm each and making good the disturbed plastered surfaces with 10mm plaster in cm 1:6 and final finish as per existing complete all as specified and as directed by engr in charge. 10 supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates ( minimum thickness of powder coating 50 micron ) including joining cleat for fixing etc., complete all as specified and as directed by engr in charge. 11 supply and fix powder coated anodised sliding / hung type aluminium window and ventilator shutters ( minimum thickness of powder coating 50 micron ) , fixed type without sash bar, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, etc., complete all as specified and as directed by engr in charge. 12 supply and fix powder coated anodized aluminium grill of 8x8mm bars size of opening 10cms size mesh with aluminium channel f angle 20x15mm aluminium frame work complete all as specified and as directed by engr in charge. 13 supply and fix 4mm thick sheet glass, ordinary quality and glazing with rubber packing, in squares not exc 0.50 sqm in each pane complete all as specified and as directed by engr in charge. 14 supply and fix 4mm thick figured glass, pin head type and glazing, in squares not exc 0.50 sqm in each pane complete all as specified and as directed by engr in charge. 15 supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by engr in charge. 16 supply and fix solar control film 50 micron reflective type sticked to glass panes complete all as specified and as directed by engr in charge. 17 supply and fix in repairs 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in pelmet boxes or in narrow widths not exc 15cm each, rebated or flat edged complete all as specified and as directed by engr in charge. 18 supply and fix in repairs harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc., complete all as specified and as directed by engr in charge. 19 supply and fix in repairs wash hand basin vitreous china, white, flat back, size 550x400mm excluding taps, waste pipe, chain and plug and including brackets complete all as specified and as directed by engr in charge. 20 supply and fix 32mm dia waste coupling of ptmt ( half or full threaded ) minimum weight 45 gms complete all as specified and as directed by engr in charge. 21 supply and fix in repairs 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without letterred hot or cold with long screwed shanks and flynuts, screwed for iron pipe complete all as specified and as directed by engr in charge. 22 supply and fix in repairs pvc cabinet mirror of size 400x300x150mm of prayag cat no 556 complete all as specified and as directed by engr in charge. 23 supply and fix in repairs wash down water closet ( pedestal pattern ) including pvc seat cover, complete white ( excluding flushing cistern and flush pipe ) complete all as specified and as directed by engr in charge. 24 supply and fix in repairs 10 litres capaity pvc valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed by engr in charge. 25 supply and fix in repairs 15mm dia stop valve cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed down for gi pipe complete all as specified and as directed by engr in charge. 26 supply and fix in repairs 15mm dia bib taps, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed down for gi pipe complete all as specified and as directed by engr in charge. 27 supply and fix in repairs brass chromium plated concealed hot and cold water valve mixer 15mm bore with 115mm long bend pipe on upper side, connecting legs, wall flanges complete all as specified and as directed by engr in charge. 28 supply and fix pvc sanitary health faucet 15mm bore for toilet complete all as specified and as directed by engr in charge. 29 supply and fix in repairs tubular towel rail brass chromium plated, 20mm dia d type, 60cm long between flanges complete all as specified and as directed by engr in charge. 30 supply and fix in repairs 125mm chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by engr in charge. 31 supply and fix pvc connections 15mm size with ptmt nuts of length 450mm complete all as specified and as directed by engr in charge. 32 supply and fix in repairs 40mm dia pvc high density polyethylene ( hdpe ) pipes of pressure rating 6 kgf / sqcm complete all as specified and as directed by engr in charge. 33 material and labour for 75mm pvc ( swr ) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by engr in charge. 34 supply and fix 75mm pvc ( swr ) bends with access door complete all as specified and as directed by engr in charge. 35 supply and fix 110mm pvc ( swr ) bends with access door complete all as specified and as directed by engr in charge. 36 taking down chowkats or frames exc 1.5 sqm but not exc 4 sqm each with shutters ( without taking off shutters from the frame ) complete all as specified and as directed by engr in charge. 37 supply and fix pressed steel frames of size 165x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and as directed by engr in charge. 38 supply and fix hold fasts and similar small articles conforming to fe 290 gde e 165 complete all as specified and as directed by engr in charge. 39 material and labour for plain cement concrete 1:2:4 type b0 ( using 12.5mm graded stone aggregates ) as in filling of pressed steel door frame complete all as specified and as directed by engr in charge. 40 supply and fix 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides covered with decorative face veneer on both faces with lipping / frame to match complete all as specified and as directed by engr in charge. 41 supply and fix 35mm thick 2nd class hardwood plain glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as nspecified in ssr part i, section 8, clause 8.24 ( a ) ; supplied and fitted to chowkats complete all as specified and as directed by engr in charge. 42 supply and fix solid pvc door frame of size 50x47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube complete all as specified and as directed by engr in charge. 43 supply and fix factory made solid pvc moulded door shutter with particle board core, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face and 2mm plain colour pvc sheet on back face complete all as specified and as directed by engr in charge. 44 supply and fix butt hinges, medium weight, 100mm long, cold rolled mild steel complete all as specified and as directed by engr in charge. 45 supply and fix aluminium anodised, barrel tower bolts, of extruded section 150mm long complete all as specified and as directed by engr in charge. 46 supply and fix 150mm long aluminium handles, oval type, stove enamelled black complete all as specified and as directed by engr in charge. 47 supply and fix 300mm long aluminium alloy anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed by engr in charge. 48 supply and fix in repairs floor door stopper of aluminium alloy body and tongue, 150mm overall length of cover plate, anodised with hard drawn steel spring, fixed in floor complete all as specified and as directed by engr in charge. 49 material and labour for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed by engr in charge. 50 material and labour for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed by engr in charge. 51 supply and fix in repairs 18 / 19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in pelmet boxes or in narrow widths not exc 15cm each, rebated or flat edged complete all as specified and as directed by engr in charge. 52 supply and fix 18 / 19mm external teak wood lipping 6mm thick, fixed with nails complete all as specified and as directed by engr in charge. 53 supply and fix 30mm flap width, continuous ( piano ) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed by engr in charge. 54 supply and fix 100mm brass handles, cast type, polished bright complete all as specified and as directed by engr in charge. 55 supply and fix 75mm hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by engr in charge. 56 material and labour for complete removal of existing treatment on old treated wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer including 3mm thick wall care putty etc., complete all as specified and as directed by engr in charge. 57 material and labour for preparation of old decorated ceiling surfaces and applying one coat of white wash etc., complete all as specified and as directed by engr in charge. 58 material and labour for complete removal of existing treatment on old treated wall surfaces and applying two coats of white wash etc., complete all as specified and as directed by engr in charge. 59 material and labour for complete removal of existing treatment on old plastered wall surfaces and applying two coats of exterior acrylic emulsion weather proof paint over a coat of primer etc., complete all as specified and as directed by engr in charge. 60 taking up or down 15mm dia steel tubing and connections complete all as specified and as directed by engr in charge. 61 supply and fix 15mm dia tubes medium grade, galvanised with all fittings and fixed to walls and ceilings complete all as specified and as directed by engr in charge. 62 taking up or down 20mm dia steel tubing and connections complete all as specified and as directed by engr in charge. 63 supply and fix 20mm dia tubes medium grade, galvanised with all fittings and fixed to walls and ceilings complete all as specified and as directed by engr in charge. 64 dismantling water tanks exc 500 ltrs and not exc 1000 ltrs capacity complete all as specified and as directed by engr in charge. 65 supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) triple layer hoisted and fixed in position complete all as specified and as directed by engr in charge. 66 supply and fix 20mm ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed ( minimum weight 210 gms ) complete all as specified and as directed by engr in charge. 67 supply and fix 20mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed by engr in charge....

Military Engineer Services - Tamil Nadu

21689175 tender for as and as to ward room annexe ( building no p 216 ) at ins rajali arakkonam 1 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) complete all as specified and as directed by engr in charge. 2 demolition of cement concrete in ground floors and pavings not exc 15 cm thickness but above ground floors complete all as specified and as directed by engr in charge. 3 material and labour for 25mm thick pcc 1:2:4 type b1 ( using 12.5mm graded stone aggregate ) as in sub base to flooring complete all as specified and as directed by engr in charge. 4 material and labour for light shade vitrified ceramic tiles 10mm thick ( square / rectangular ) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors / etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles including screed bed 15mm thick in cement mortar 1:4 etc., complete all as specified and as directed by engr in charge. 5 all as per item no. 04 here in before but in skirting with 10mm thick in cement mortar 1:3 etc., complete all as specified and as directed by engr in charge. 6 material and labour for coloured non skid ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc., over 15mm thick screed bed in cement mortar 1:4 set set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and as directed by engr in charge. 7 material and labour for coloured glazed ceramic tiles in vertical surface 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick back coat in cm 1:3 complete all as specified and as directed by engr in charge. 8 taking down steel windows of any description with frames including guard bars ( glazed window, flyproof window and guard bars ) area not exc 1 sqm each and making good the disturbed plastered surfaces with 10mm plaster in cm 1:6 and final finish as per existing complete all as specified and as directed by engr in charge. 9 taking down steel windows of any description with frames including guard bars ( glazed window, flyproof window and guard bars ) area exc 1 sqm but not exc 2 sqm each and making good the disturbed plastered surfaces with 10mm plaster in cm 1:6 and final finish as per existing complete all as specified and as directed by engr in charge. 10 supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates ( minimum thickness of powder coating 50 micron ) including joining cleat for fixing etc., complete all as specified and as directed by engr in charge. 11 supply and fix powder coated anodised sliding / hung type aluminium window and ventilator shutters ( minimum thickness of powder coating 50 micron ) , fixed type without sash bar, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, etc., complete all as specified and as directed by engr in charge. 12 supply and fix powder coated anodized aluminium grill of 8x8mm bars size of opening 10cms size mesh with aluminium channel f angle 20x15mm aluminium frame work complete all as specified and as directed by engr in charge. 13 supply and fix 4mm thick sheet glass, ordinary quality and glazing with rubber packing, in squares not exc 0.50 sqm in each pane complete all as specified and as directed by engr in charge. 14 supply and fix 4mm thick figured glass, pin head type and glazing, in squares not exc 0.50 sqm in each pane complete all as specified and as directed by engr in charge. 15 supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by engr in charge. 16 supply and fix solar control film 50 micron reflective type sticked to glass panes complete all as specified and as directed by engr in charge. 17 supply and fix in repairs 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in pelmet boxes or in narrow widths not exc 15cm each, rebated or flat edged complete all as specified and as directed by engr in charge. 18 supply and fix in repairs harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc., complete all as specified and as directed by engr in charge. 19 supply and fix in repairs wash hand basin vitreous china, white, flat back, size 550x400mm excluding taps, waste pipe, chain and plug and including brackets complete all as specified and as directed by engr in charge. 20 supply and fix 32mm dia waste coupling of ptmt ( half or full threaded ) minimum weight 45 gms complete all as specified and as directed by engr in charge. 21 supply and fix in repairs 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without letterred hot or cold with long screwed shanks and flynuts, screwed for iron pipe complete all as specified and as directed by engr in charge. 22 supply and fix in repairs pvc cabinet mirror of size 400x300x150mm of prayag cat no 556 complete all as specified and as directed by engr in charge. 23 supply and fix in repairs wash down water closet ( pedestal pattern ) including pvc seat cover, complete white ( excluding flushing cistern and flush pipe ) complete all as specified and as directed by engr in charge. 24 supply and fix in repairs 10 litres capaity pvc valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed by engr in charge. 25 supply and fix in repairs 15mm dia stop valve cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed down for gi pipe complete all as specified and as directed by engr in charge. 26 supply and fix in repairs 15mm dia bib taps, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed down for gi pipe complete all as specified and as directed by engr in charge. 27 supply and fix in repairs brass chromium plated concealed hot and cold water valve mixer 15mm bore with 115mm long bend pipe on upper side, connecting legs, wall flanges complete all as specified and as directed by engr in charge. 28 supply and fix pvc sanitary health faucet 15mm bore for toilet complete all as specified and as directed by engr in charge. 29 supply and fix in repairs tubular towel rail brass chromium plated, 20mm dia d type, 60cm long between flanges complete all as specified and as directed by engr in charge. 30 supply and fix in repairs 125mm chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by engr in charge. 31 supply and fix pvc connections 15mm size with ptmt nuts of length 450mm complete all as specified and as directed by engr in charge. 32 supply and fix in repairs 40mm dia pvc high density polyethylene ( hdpe ) pipes of pressure rating 6 kgf / sqcm complete all as specified and as directed by engr in charge. 33 material and labour for 75mm pvc ( swr ) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by engr in charge. 34 supply and fix 75mm pvc ( swr ) bends with access door complete all as specified and as directed by engr in charge. 35 supply and fix 110mm pvc ( swr ) bends with access door complete all as specified and as directed by engr in charge. 36 taking down chowkats or frames exc 1.5 sqm but not exc 4 sqm each with shutters ( without taking off shutters from the frame ) complete all as specified and as directed by engr in charge. 37 supply and fix pressed steel frames of size 165x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and as directed by engr in charge. 38 supply and fix hold fasts and similar small articles conforming to fe 290 gde e 165 complete all as specified and as directed by engr in charge. 39 material and labour for plain cement concrete 1:2:4 type b0 ( using 12.5mm graded stone aggregates ) as in filling of pressed steel door frame complete all as specified and as directed by engr in charge. 40 supply and fix 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides covered with decorative face veneer on both faces with lipping / frame to match complete all as specified and as directed by engr in charge. 41 supply and fix 35mm thick 2nd class hardwood plain glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as nspecified in ssr part i, section 8, clause 8.24 ( a ) ; supplied and fitted to chowkats complete all as specified and as directed by engr in charge. 42 supply and fix solid pvc door frame of size 50x47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube complete all as specified and as directed by engr in charge. 43 supply and fix factory made solid pvc moulded door shutter with particle board core, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face and 2mm plain colour pvc sheet on back face complete all as specified and as directed by engr in charge. 44 supply and fix butt hinges, medium weight, 100mm long, cold rolled mild steel complete all as specified and as directed by engr in charge. 45 supply and fix aluminium anodised, barrel tower bolts, of extruded section 150mm long complete all as specified and as directed by engr in charge. 46 supply and fix 150mm long aluminium handles, oval type, stove enamelled black complete all as specified and as directed by engr in charge. 47 supply and fix 300mm long aluminium alloy anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed by engr in charge. 48 supply and fix in repairs floor door stopper of aluminium alloy body and tongue, 150mm overall length of cover plate, anodised with hard drawn steel spring, fixed in floor complete all as specified and as directed by engr in charge. 49 material and labour for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed by engr in charge. 50 material and labour for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed by engr in charge. 51 supply and fix in repairs 18 / 19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in pelmet boxes or in narrow widths not exc 15cm each, rebated or flat edged complete all as specified and as directed by engr in charge. 52 supply and fix 18 / 19mm external teak wood lipping 6mm thick, fixed with nails complete all as specified and as directed by engr in charge. 53 supply and fix 30mm flap width, continuous ( piano ) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed by engr in charge. 54 supply and fix 100mm brass handles, cast type, polished bright complete all as specified and as directed by engr in charge. 55 supply and fix 75mm hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by engr in charge. 56 material and labour for complete removal of existing treatment on old treated wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer including 3mm thick wall care putty etc., complete all as specified and as directed by engr in charge. 57 material and labour for preparation of old decorated ceiling surfaces and applying one coat of white wash etc., complete all as specified and as directed by engr in charge. 58 material and labour for complete removal of existing treatment on old treated wall surfaces and applying two coats of white wash etc., complete all as specified and as directed by engr in charge. 59 material and labour for complete removal of existing treatment on old plastered wall surfaces and applying two coats of exterior acrylic emulsion weather proof paint over a coat of primer etc., complete all as specified and as directed by engr in charge. 60 taking up or down 15mm dia steel tubing and connections complete all as specified and as directed by engr in charge. 61 supply and fix 15mm dia tubes medium grade, galvanised with all fittings and fixed to walls and ceilings complete all as specified and as directed by engr in charge. 62 taking up or down 20mm dia steel tubing and connections complete all as specified and as directed by engr in charge. 63 supply and fix 20mm dia tubes medium grade, galvanised with all fittings and fixed to walls and ceilings complete all as specified and as directed by engr in charge. 64 dismantling water tanks exc 500 ltrs and not exc 1000 ltrs capacity complete all as specified and as directed by engr in charge. 65 supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) triple layer hoisted and fixed in position complete all as specified and as directed by engr in charge. 66 supply and fix 20mm ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed ( minimum weight 210 gms ) complete all as specified and as directed by engr in charge. 67 supply and fix 20mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed by engr in charge....

Hindustan Petroleum Corporation Limited - Tamil Nadu

19420761 tender for csr works pennalurpet school supply and application of two coats of white wash at the designated areas as per instructions of hpcl officer in charge, synthetic enamel paint application on wood works / plastered surface with minimum 2 coats. job includes supply of material, manpower, tools, tackles required to complete the job. paint manufactured equivalent as approved by engineer incharge. colour of t, supplying transporting, stacking, straightening, cleaning, cutting, bending, placing, tying in position (including providing 16 gauge annealed binding wire) high yield strength deformed ( hysd ) tmt bars (thermo mechanically treated bars) conforming to is 1786 ( latest edition / revision ) as reinforcement steel as per drawings, technical specifications mentioned in the tender & as directed by the site in charge. (the rate shall be applicable for any height & depth), providing and laying of pvc pipes of 8 kg/cm2 pressure in proper position with all accessories, fitting etc. size:any, supply and fixing heavy duty acl roofing sheets of approved manufacturer, fixing in position with necessary hardware, washers etc. for the roof, barricading etc. as per instructions. contractor to bring the samples for approval, wash basin sup & installation, shamiana 18*18, chairs hiring for one day, window concrete, cable wiring works, sup & inst of tube lights, pv taps sup & inst, excavtion of earth, bench and desk, excavation for foundation upto required depth (maximum upto 3 meters) below existing ground level in any type of soil/soft rock/concrete floor . rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, back filling after the construction of foundation, compacting by the side of the foundation. job includes shifting of surplus excavated earth to one place for further disposal as directed by eic, etc....

Hindustan Petroleum Corporation Limited - Tamil Nadu

19072155 tender for canopy for ows at tirunelveli ird excavation for foundation upto required depth below existing ground level up to 1.5m in any tyoe odf soil except hard rock. rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, trenches/plinth beam etccompacting by the side of the foundation and disposal of surplus excavated earth within/outside hpcls premises to an unobjectionable place, as directed by the engineer in charge including spreading, watering and compaction, complete. the measurement of the excavation would be based on actual depth of excavation with applicable rate for different depths. , plain cement concrete (1:3:6) providing and laying plain cement concrete of nominal volumetric mix 1:3:6 (1 cement:3 sand:6 crushed stone aggregates) with 20mm and down size graded aggregates below plinth protection and any other work as per requirement including any required permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc all complete as per instructions of hpcl engineer in charge., supply and application of two coats of white wash at the designated areas as per instructions of hpcl officer in charge, providing and laying 12mm thk plastering in cm 1:4 in single coat to all interior walls., supplying, transporting, fabricating, erecting in position in position of pre fabricated steel structures at all elevations for canopy using structural steel sections ismb/ismc/isa conforming to is:2062 and is 226 , including cutting, welding or bolting, supply of bolts/nuts/washers etc., complete as per drawings including surface preparation and applying one coat of zinc phosphate primer before erection, one coat after erection and two coats of synthetic enamel paint as per specification after erection and all materials and labour complete. ( no welding is permitted at site). etc...

Tamil Nadu Electricity Board - Tamil Nadu

18548826 tender for colour washing using fine screened shell lime with two coats over one coat of white wash including cost of all materials scaffolding labour with all leads and lift .complete.etc., supplying and fixing y shaped 50x50x5mm g.i.angle iron post on top of compound wall for fixing barbed wire as directed by the site engineer including cost of all materials labour lead, lift etc., complete.1no. painting two coats with ready mixed enamel paint of approved quality over the new iron work including cost of all materials, lead , lift, etc complete providing steel reinforcement for rcc work including cost of steel, binding wire labour for fabircation, placing in position lead, lift, etc complete refilling basement with excavated soil in layers of not more than 15 cm thick well watered, rammed and consolidated including cost ofall materials, lead, lift, etc., complete. supplying and fixing 3 rows of barbed wire in horizontal and vertical crossing at 0.23m interval with semi circular curve at top & bottom in both vertical & sloped arm of y post including cost of materials labour lead lift etc., complete, as directed by the engineer site...

Tamil Nadu Electricity Board - Tamil Nadu

18548820 tender for dismantling of brick work in lime mortar above and below ground level including cost of labour, lead, lift, t & p etc complete as directed by the engineer at site. earth work excavation and depositing on back with initial lead & lift as directed by the engineer in charge including cost of t&p, labour etc. in complete. filling of basement with sand in layers of not more than 15 cm thick well watered, rammed and consolidated including cost of all materials, lead, lift, etc., complete. plain cement concrete 1:4:8 below grade beam 40mm metal for flooring including cost of all materials labour lead lift etc., complete, as directed by the site engineer rr masonary in cm 1:5 for foundation and basement using slag cement including cost of rubble stone, all materials , labour lead lift etc complete providing plinth beam m20 using 12 to 20 mm hbs and cement with minimum cement content of 360kg per cum and water cement ratio 0.5 including removal of old slab, form work, cos of all materials, labour, lead, lift, curing but excluding cost of providing steel reinforcement plinth beam providing plinth beam m20 using 12 to 20 mm hbs and cement with minimum cement content of 360kg per cum and water cement ratio 0.5 including removal of old slab, form work, cos of all materials, labour, lead, lift, curing but excluding cost of providing steel reinforcement tie beam brick work in c m 1:5 using fly ash bricks including cost of all materials, lead, lift, curing etc complete for & super structure. plastering with cement mortar ( 1:3 ) 12mm thick for compound wall in outer surfaces including cost of all materials labour lead lift curing etc., complete colour washing using fine screened shell lime with two coats over one coat of white wash including cost of all materials scaffolding labour with all leads and lift .complete.etc., supplying and fixing y shaped 50x50x5mm g.i.angle iron post on top of compound wall for fixing barbed wire as directed by...

Hindustan Petroleum Corporation Limited - Tamil Nadu

18450404 providing and applying two coats of colour/white wash of approved colour/make and shade to old/ new plastered surface including scaffolding, scrapping, step ladder, scrapping, brushing and brooming and adding adhesives to get proper bonding, cleaning the floor including filling all cracks, holes and undulations with cement mortar and curing the same. rates include scaffolding, filling the cracks, holes with cement mortar etc(whitewashing of walls)...

Hindustan Petroleum Corporation Limited - Tamil Nadu

17955975 tender for painting of valves wall supply and application of 100 % acrylic interior/exterior emulsion (first quality) approved paints or approved make or approved equivalent approved by the engineer in charge on the prepared surface of any shade as instructed by the engineer in charge including the filling of voids/holes , lettering works: lettering at various places by painting :any lettering work to be done as per the advice of hpcl officer on structure , supply and application of two coats of white wash at the designated areas as per instructions of hpcl officer in charge. painting of 50 hp pump, motor ,arv,base frame as per the direction of eic supply and application of one or more coats of two pack polyamidoamine cured fortified epoxy super high build mastic surface tolerant coating as per the manufacturers recomendations to achieve 125 micron dft. rate shall be inclusive of providing all materials tools and tackles. etc...

Hindustan Petroleum Corporation Limited - Tamil Nadu

17115462 tender for csr works ponneri school supply and application of two coats of white wash at the designated areas as per instructions of hpcl officer in charge lettering works: lettering at various places by painting:any lettering work to be done as per the advice of hpcl officer on structure, pipeline, tank, ttg, twg, etc places. lettering includes both alphabets and numerical. measurement will be paid per inch basis. painting to be done using any color as advised by hpcl etc...

Hindustan Petroleum Corporation Limited - Tamil Nadu

16243613 tender for maintenance and repair works at retail outlets in dindigul and ramnad sales area under madurai retail ro excava hardrock 1.5 3.0 mts , sand filling layers 150mm , crushedstonesand filling 150mm , murrum filling layers 150mm , earth filling , murrum filling , pcc , rcc 1:1.5:3 for culvert slab , ready mix concrete(rmc m 30) , bored cast in situ 350 mm dia , brick masonry substructure , brick masonry structure 345 mm , partition 115 mm brick masonry , concrete hollow blocks , rrm super structure , rubble solling 230 mm thk , brick pitching , plastering 6 mm thk , smoothplastering 12mm thk , weep holes , ms pipe railing , chain link fencing , hume pipes 1000 mm dia (np4 , anti termite treatment , ceramictile 450mmx450mm, terracotta tiles , cermictiledado , hp logo fixing , concrete tile walkway , white wash , oil bound distember , acrylicemulsion paint(int/grd) , water proofcement paint , anod.al.glz. door 12mm glass , al. panelled door , steel doors , flush door 900x2100mm , rolling shutter , automatic shoe polish machine , ss staircase railing , soap tray , liquid soap dispensers , towel rail , 15mm dia pillar cocks , 15mm dia half turn cocks , 15mm dia exposed gi pipe ,...

Archaeological Survey Of India - Tamil Nadu

13499431 tender for revised special repair ( p ) to clive’s building, chennal for 2017 18 as detailed below applying two coats of white wash to the ceiling after cleaning the existing surface, etc., complete, applying two coats of synthetic enamel paint to the existing iron members after thoroughly cleaning the surface, etc., complete, applying two coats of synthetic enamel paint to the existing wooden members after thoroughly cleaning the surface etc., complete, applying emulsion plastered cleaning applying including labour complete two coats of acrylic paint to the newly surface after the area and one coat of primer cost of material and charges, etc....

Hindustan Petroleum Corporation Limited - Tamil Nadu

10948865 maintenance and repair of 1 reinforcement steel 2 structural steel 3 ms pipe railing 4 precastconcretepoles fencing 5 hp logo fixing 6 hy. floor spring 7 flush door 900x2100mm: 8 flush door 750x2100mm 9 ms fan hooks 10 mortice lock 11 door closer 12 concealed door lock works 13 door stopper works 14 concealed door closer works 15 european type w / c wall 16 europeantype w / c floor 17 indian type w / c 18 urinals 19 large urinals 20 urinals with built in sensors 21 urinal divisional plate 22 urinal div.plate ceramic 23 urinals sensors 24 hand wash basin 25 countertop washbasin oval type 26 sensor taps faucet 27 cp towel ring 28 automatic hand dryer 29 auto freshener 30 automatic shoe polish machine 31 mirror 600x600x5.5 32 soap tray 33 liquid soap dispensers 34 toilet paper holder 35 towel rail 36 15mm dia stop cocks 37 15mm dia bib cocks 38 15mm dia pillar cocks 39 15mm dia half turn cocks 40 health faucet ( hygi spray ) 41 40mm dia gate valve 42 32mmdia gate valve 43 25mm dia gate valve 44 15mm dia gate valve 45 water tank 1000 ltrs 46 water tank 5000 ltrs 47 nahani trap 48 gully trap with chamber 49 25mm dia non return valve: 50 15mm dia non return valve 51 float valve 52 600x600x600mm inspn. chambers 53 450x450x600mm inspn. chambers 54 sewer trap chamber 55 septic tank ( 25 person ) 56 septic tank ( 75 person ) 57 soakpit 2.5 mdiax3.0 m. depth 58 pt.wiring switch lt / fan 59 6a socket switch 60 6a socket switch indepenently 61 6 / 16a socket switch 62 ac point 63 ceiling fans 1400 mm sweep 64 exhaust fans 305mm dia 65 exhaust fans 230mm dia 66 1x36w tube light fitting 67 18w cfl lamp 68 13 w cfl lamp 69 2x36w tube light fitting 70 recessmount optic fitting 2x36 71 recessmountmirror optic 4 x18w 72 tel. socket point 2 pair 73 tel. tag block 5 pairs 74 tel. socket 75 meter board 76 panel brd t 1 77 panel brd t 2 78 63a tpn mcb db 79 32a tpn mcb db 80 3.5cx120sqmm al cable end ter 81 3.5cx95 sqmm al cable end ter 82 3.5cx70 sqmm al cable end ter 83 3.5cx50 sqmm al cable end ter 84 3.5cx35sqmm end termination 85 4cx16sqmm end termination 86 4 core x 6 sqmm end term. 87 4cx2.5 sqmm end termination 88 3cx2.5sqmm end ter. dob. comp. 89 3cx1.5sqmm end ter. dob. comp. 90 4cx2.5 sqmm end term ( flp ) 91 3cx2.5sq end ter.dobcomp ( flp ) 92 junction box flp 93 junction box nflp 94 octagonalgalvapole6.0 mht sin 95 octagonalgalv pole6.0 m ht dou 96 grp single arm pole 6.0 m. ht 97 grp double arm pole 6.0 m. ht 98 s & f of streetlight fitting 99 s & f of hoarding light 70 w 100 fix.hpclsupplied street light. 101 fix hpclsupplied hoardinglight 102 earthing pit plate electrode 103 earthing pit pipe electrode 104 emergencyswitch ( mashrum ) 105 s & f canopy light fixtures 106 fix hpcl supplied canopy 107 1 phase servostabiliser 5 kva 108 250 va cvt 109 500 va cvt 110 ins.chambers 600x600 111 ins chambers 450x450 112 900x900mmd.i.cover ( heavy duty ) 113 600x600mmd.i.cover ( heavy duty ) 114 450x450mmd.i.cover ( heavy duty ) 115 45 kl tank installation 116 35kl tank instln. 117 22kl tank instln. 118 16kl tank instln. 119 9kl tank instln. 120 instln. of mono / duel pumps 121 instln. of dual / 2t mix pumps 122 instln. of mpd pumps 123 angular check valve ( nrv ) 40mm 124 angular check valve ( nrv ) 50mm 125 vertical check valve 40mm 126 vertical check valve 50mm 127 horizondal check valve 40mm 128 horizondal check valve 50mm 129 flange joint 40mm dia 130 flange joint 50mm dia 131 flange jointn80mm dia 132 m.s union t 40mm 133 m.s union t 50mm 134 m.s union t 80mm 135 ms bush 40mm x 50mm 136 ms bush 80mm x 50mm 137 ms bush 40mm x 100mm 138 ms bush 80mm x 100mm 139 ms coupling 40mm dia 140 ms coupling 50mm dia 141 ms coupling 80mm dia 142 ms nipple 40mm dia 143 ms nipple 50mm dia 144 ms nipple 80mm dia 145 ball valve 15mm dia 146 ball valve 20mm dia 147 ball valve 25mm dia 148 s / f ball valves 40mm dia 149 s / f ball valves 50mm dia 150 installation of stp 151 al fill cap 50mm dia 152 al dip cap 50mm dia 153 silica gel trap 154 tee vent hood 50mm dia 155 fill cap with lock 40 mm dia 156 dip cap with lock 40mm dia 157 tee vent hood 40mm dia 158 exuming 9 kl tank 159 exuming 14 / 16kl tank 160 exuming 22 kl tank 161 exuming 45 kl tank 162 exuming 70kl tank 163 removal of st. steel 164 shifting of eb mains 165 removal of yard light pole 166 removing of mono / duel pumps 167 removing of mpd pumps 168 fill pipe brass coupling 169 instln. of air tower 170 heavyduty brass crocodile clip 171 structural steel for canopy 172 canopy light fixtures 150 watt 173 yeild test 174 s&f submercible pump 1.5 hp 175 well cap 150 mm dia 176 single phase 1.5 hp jet pump 177 geologicaltesting for borewell 178 site clearance 179 excavation in earth upto 1.5 m 180 excavation 1.5 to 3 m 181 excavation 3 to 4.5 182 excavation soft rock upto1.5m 183 excava soft brock 1.5 3.0 mt 184 excava soft rock 3.0 4.5 mts 185 excavation hard rock upto1.5m 186 excava hardrock 1.5 3.0 mts 187 excava hard rock 3.0 4.5 mts 188 filling of excavated earth wor 189 sand filling layers 150mm 190 crushedstonesand filling 150mm 191 murrum filling layers 150mm 192 earth filling 193 murrum filling 194 pcc 1:4:8 195 pcc 1:3:6 196 pcc 1:2:4. 197 pcc 1:2:4 for dpc 198 pcc 1:2:4 for coping 199 rcc1:1.5:3 footing / pile cap 200 rcc 1:1.5:3 columns / beams 201 rcc1: 1.5:3roof slab / chajja 202 rcc 1:1.5:3 for culvert slab 203 rcc 1:1.5:3 bottomraft tank 204 rcc 1:1.5:3 top slab tank 205 ready mix concrete ( rmc m 30 ) 206 ready mix concrete ( rmc m 25 ) 207 rmc m 150 superstructor 350mm 208 rmc m 150 superstructor 300mm 209 bored cast in situ 350 mm dia 210 bored cast in situ 300 mm dia 211 bored cast in situ 350 mm dia 212 bored cast in situ 300 mm dia 213 brick masonry substructure 214 brick masonry superstructure 215 brick masonry structure 345 mm 216 fly ash bricks 217 concrete hollow blocks 218 rrm substructure 219 rrm super structure 220 rubble solling 230 mm thk 221 rubble solling 150 mm thk 222 brick on edge 223 brick pitching 224 flush pointing 225 raised pointing 226 ceiling plastering 6 mm thk 227 plastering 6 mm thk 228 smoothplastering 12mm thk 229 plastering 20mm thk 230 weep holes 231 chain link fencing 232 barbed wire fencing 233 hume pipes 1000 mm dia ( np4 ) 234 hume pipes 900 mm dia ( np3 ) 235 hume pipes 600 mm dia ( np3 ) 236 hume pipes 450 mm dia ( np 3 ) 237 hume pipes 300 mm dia ( np 2 ) 238 hume pipes 250 mm dia ( np 2 ) 239 hume pipes 200 mm dia ( np 2 ) 240 hume pipes 150 mm dia ( np 2 ) 241 anti termite treatment 242 rectifiedtiles compound wall 243 ceramictile 600mmx600mm 244 ceramictile 450mmx450mm 245 ceramictile 300mmx300mm 246 vitrifiedtile900mm x 900mm 247 vitrifiedtile600mm x 600mm 248 terracotta tiles 249 manglore tiles on roof / chajja 250 mosaic tiles 251 granite tile flooring 252 ceramic tile skirting works 253 virtified tile flooring ski 254 20mm tk granite slab skirtin 255 ips flooring 256 cermictiledado ( 300mmx 200 mm ) 257 cermictiledado ( 300mmx 400 mm ) 258 cermictiledado ( 300mmx 600 mm ) 259 ceramic tile borders 260 granite slab18 mm black 261 18mm tk granite works for stai 262 kotastonefloor:600mm x 600mm 263 kota stone skirting 264 kota stone steps 265 granite sill slab for windows 266 eurocon tiles for walkway 267 eurocon tiles for steps / stai 268 18 mm tk cuddapah stone works 269 25 mm tk cuddapah stone works 270 40 mm tk cuddapah stone works 271 brickbat terrace water proof. 272 integral terrace waterproofing 273 chajja water proofing 274 white wash 275 oil bound distember 276 snowcem painting for 10sqm 277 santex mat works 278 apex whether coat works 279 acrylicemulsion paint ( int / grd ) 280 acrylicemulsion paint ( ext ) 281 plasticemulsion paint 282 water proofcement paint 283 sy. enml. paint over wall 284 sy.enml.paint over steel / wood 285 pop punning 286 pop moulding 287 ms grill 288 anod.al.glz. door 12mm glass 289 12mm toughened 290 aluminum fixed glass frame wo 291 pdr.coat.al glz. fixed 10mm 292 al. panelled door 293 aluminium bison lam panneled 294 al. windows openable 295 al. sliding windows 3 track 296 al. sliding windows 2 track 297 al. louvered ventilator 298 fixing of 6mm tk glass works 299 steel windows 300 steel doors 301 rolling shutter 302 grill in rolling shutter 303 pvc doors 30mm tk 304 35mm tk flush doors 305 nonasbestos cement sheet roof 306 nonasbestos cement sheet side 307 providing and laying 20 swg 308 laying of supplied g.i c she 309 laying of supplied ac sheet 310 barricading 311 gy. board false ceiling 312 minaral fibre false ceilling 313 ss grab bar design a / b 314 mirror 5.5 mm thk 315 15mm dia concealed gi pipe 316 20mm dia concealed gi pipe 317 15mm dia exposed gi pipe 318 20mm dia exposed gi pipe 319 25mm dia exposed gi pipe 320 32 mm dia exposed gi pipe 321 40 mm dia exposed gi pipe 322 upvc pipe 40 mm dia 4kg / sqcm 323 upvc pipe 15 mm dia 4kg / sqcm 324 upvc pipe 20 mm dia 4kg / sqcm 325 upvc pipe 25 mm dia 4kg / sqcm 326 upvc pipe 32mm dia 4kg / sqcm 327 upvc pipe 40 mm dia 4kg / sqcm 328 upvc pipe 50 mm dia 4kg / sqcm 329 cpvc piping ( is 15778 ) 15 mm 330 cpvc piping ( is 15778 ) 20 mm 331 cpvc piping ( is 15778 ) 25 mm 332 cpvc piping ( is 15778 ) 32 mm 333 cpvc piping ( is 15778 ) 40 mm 334 cpvc piping ( is 15778 ) 50 mm 335 160mmdia pvc swr pipes 336 110 mm dia pvc swr pipes 337 80 mm dia pvc swr pipes 338 4x10+1x6 sqmm multist.frls cu 339 4x6+1x4 sqmm multist. frls cu 340 frls multistr. 1.5 sqmm copper 341 frls multistr. 2.5 sqmm copper 342 frls multistr. 4.0 sqmm copper 343 frls multistr. 6.0 sqmm copper 344 pvc conduit med. is:9537 25mm 345 pvc conduit med. is:9537 32 mm 346 pvc conduit med. is:9537 40 mm 347 3.5cx 120 sqmm al cable 348 3.5 c x 95 sqmm al cable 349 3.5cx 70 sqmm al cable 350 3.5cx 50 sqmm al cable 351 3.5cx35sqmm al cable 352 4cx16sqmm al cable 353 4cx6sqmm al cable 354 4cx2.5sqmm copper cable 355 3cx2.5sqmm copper cable 356 cable trench excavation 357 10 swg copper wire 358 gi flat 50x6 mm 359 gi flat 25x3 mm 360 ms chequred plate 361 isi marked rubber mat 12mm 362 gsb layer 363 wbm 1st layer 100 mm thk. 364 wbm 2nd layer 75 mm thk. 365 wbm 3rd layer 75 mm thk. 366 bbm 100mm 367 bituminous macadam 75mm 368 semi dense bitu.conc. 25mm thk 369 semi dense bitu.conc. 40mm thk 370 semi dense bitu.conc.100mm thk 371 premix carpet 50 mm 372 premix carpet 100 mm 373 seal coat 12 mm 374 mastic wearing coarse 25mm 375 linear delineation sheeting 376 s / l driveway grey paver m 40 377 s / l dr.way colour paver m 40 378 s / l refl. grey d / w paver m40 379 refl. coloured d / w paver m40 380 s / l grass pavers m 30 381 s / l pedestrian pavers mix m 25 382 removal and relaying of pavers 383 dressing of driveway 384 rcc 1:2:4 driveway 385 rcc with m 25 ready mix 386 rcc 1:2:4 without dewatering 387 transp. of 45 kl beyond 50 km 388 transp. of 35 kl beyond 50 km 389 transp. of 22 klbeyond 50 km 390 transp. of 16 kl beyond 50 km 391 transp. of 9 kl beyond 50 km 392 tr.mono / dueldu beyond 50km 5no 393 tr.mpd bey50 km in lot 5 no 394 pump island 395 doping of 40mm dia pipe works 396 doping of 50mm dia pipe works 397 doping of 80mm dia pipe works 398 pressure test of 40mm dia pip 399 pressure test of 50mm dia pip 400 pressure test of 80mm dia pip 401 40mm dia pipeline works 402 50mm dia pipeine works 403 80mm dia pipeline works 404 s / f / l ms c cl.welded pl40mmdia 405 s / f / l ms c cl.welded pl50mmdia 406 s / f / l ms c cl.welded pl80mmdia 407 granite slab 408 granite tiles 409 dismantling rcc 410 removal of ac sheet 411 excavation in rcc 412 dis. of brick masonary 413 removal of false ceiling 414 removal of canopy roofing 415 removal of ms / al doors 416 removal of fencing 417 breaking of tiles / granite wo 418 re fixing of fencing works 419 removing of trench slabs 420 relaying of trench slabs 421 laying of supplied granite wor 422 breaking of water proofing wor 423 dismantling of w / c , w / b and u 424 dismantling of master pole wi 425 dismantling of emplem sign 426 dis air compressor 427 dis air tower 428 dis yard / island lights 429 dis decorative light fittings 430 dis barbed wire fencing 431 dis grand id signage 432 rem & refixing spines, spreade 433 removing and re fixing grand 434 dismanling of 40mm dia m.s pi 435 dismantling of 50mm dia m.s pi 436 dismantling of 80mm dia m.s p 437 installation of air compresso 438 installation of air tower / g 439 installation of dg set works 440 re fixing grand id signage 441 inst supplied master pole / club 442 inst supplied hoarding board 443 inst hpcl supplied dg 444 inst supplied q&q tower 445 fixing tyre inflator 446 inst dg set panle 447 repair of aluminium gutter 10 448 re installation of supplied ca 449 removal of pavers 450 relaying of pavers 451 laying of supplied track dek c 452 laying of supplied false ceil 453 asphalting repair works 454 wbm repair works 455 relaying of 40 mm dia p / l 456 relaying of 50 mm dia p / l 457 relaying of 80 mm dia p / l 458 cable tray 300 mm wide 459 cable tray 150 mm wide 460 gasket on tank manhole 461 fdn.bolt for stru. canopy 462 roofing tracdek hi rib 100 463 track dek clippon type 464 false ceiling 465 ms fascia 466 al gutter 467 6 pvc pipes of 6 kg / sqcm 468 4pvc pipes of 6 kg / sqcm 469 borewell 6 dia beyond 100 470 borewell 4.5 dia beyond 100 471 s&f of upvc pipe 6 dia 472 s&f of screen pipe 6 dia 473 3 c x 2.5 copper flat cable 474 supplying and fixing of 7 hd 475 supplying and fixing of 5 hd 476 supplying and fixing of stott 477 supplying and fixing of stotte 478 s&f of 40 mm dia hdpe pipe 479 25 mm nb hdpe pipe 480 raised pavement markers 481 tran.70 kltank 50 km 482 trans.70 kl tank beyond 50 km 553 6a 2 in 1 modular socket 554 20a 5 in 1 modular socket 555 40w electronic fan regulator 556 electronic energy meter 557 32a tpn mainswitch 558 63a tpn mainswitch 559 125a tpn mainswitch 560 32a fuse carrier 561 63a fuse carrier 562 125a fuse carrier 563 200a fuse carrier 564 300a fuse carrier 565 7 / 20 gi wire 566 1 gi pipe for eb line 567 fixing automatic power factor 568 dispensing unit batteries 569 cable route marker 570 test and certify old earthing 571 50 x 6 copper strip 572 25 x 6 copper strip 573 25 x 3 copper strip 574 liasoing with eb 575 providing rain water harvestin 576 ss pipe line 25mm dia 577 ss pipe line 40mm dia 578 ss pipe line 50mm dia 579 ss pipe line 80mm dia 580 seamless pipeline 50mm dia 581 seamless pipeline 80mm dia 582 emergency light in canopy 583 first aid chart 584 earth pit boards 585 supply of manure 586 laying red earth & manure 587 supply & planting korean grass 588 supply & planting fig / casurina 589 alu dip rod 3m length 590 alteration of suction pipeline 591 hoarding art painting 592 hoarding / comp wall lettering 593 repainting hoarding board 594 cleaning of banding 595 cleaning canopy false ceiling 596 cleaning grand id 597 cleaning signature pylon 598 cleaning city pylon 599 removing water / dead stock 600 brass mesh 601 10 kg dcp extinguishers 602 fire bucket stand 603 sun control film 604 precast rcc manhole cover 600x 605 precast rcc manhole cover 450x 606 hiring air compressor 8 hours 607 transporting ms ladder 608 checking / reconnecting cables 609 supply of unskilled labour 610 dis canopy / hoarding with crane 611 crane for loading / unloading 612 pre lubricated pipes 50mm dia 613 pre lubricated pipes 80mm dia 614 labour charges for disconnect 615 labour charges for rem m / h cov 616 labour charges for ref m / h cov 617 s / f 16mm dia 50mm length bolt 618 cleaning external 9kl tank 619 cleaning external 16kl tank 620 cleaning external 22kl tank 621 removing dead stock 9kl tank 622 removing dead stock 16kl tank 623 removing dead stock 22kl tank 624 single line diagram 625 painting outside panel 626 painting master pole 627 painting club hp pole 628 painting yard light pole 629 painting fire buckets 630 painting fill / vent / dip pipe 631 painting 1.2 1.5m high barbe 632 scraping / painting old barbed 633 painting compresson / motor 634 painting flood light pole 635 painting t light pole 636 painting barrel racks 637 painting lubster 638 painting ceiling fans 639 painting light fittings 640 painting air tower / q&q 641 painting canopy columns 642 painting hindustan petroleum 643 painting dealer name 644 painting free air & water 645 painting drive in & out 646 painting toilet 647 painting no smoking 648 painting filter paper availabl 649 painting storage lic. no. 650 painting suggestion book avail 651 painting petrol / diesel 652 painting address of dealer 653 painting 600mm with colour cod 654 painting 1200mm with colour co 655 painting hp monogram 656 painting red / blue bands 657 enamel painting fire bucket / no 658 painting of zebra marking 659 painting of route marking 660 spray painting canopy false ce 661 painting quick care point 662 painting of arrow marks 663 automation tank modification w...

Military Engineer Services - Tamil Nadu

8896939 tender for ( h ) white wash, colour wash painting of wood & steel surfaces with weather lakhs proof paint etc. in flood affected buildings under periodicity in zone a & c & d under ge chennai....

Municipal Corporation - Tamil Nadu

8248675 construction of compund wall and and maintenance and repairs of flooring work, tiles work, colour wash, white wash, supply of furniture with wiring arrangement...

Municipal Corporation - Tamil Nadu

8242657 construction of compund wall and and maintenance and repairs of flooring work, tiles work, colour wash, white wash, supply of furniture with wiring arrangemetns sl no.8 to 15...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

8044162 carrying out the balance works in the ladies toilet block located in the first grid of +17m floor of stg building such as laying of sewer lines, water lines, fixing of sanitary fittings, floor finish, wall finish, ceiling plastering, white wash, colour wash etc. extended...