Rural Development And Panchayats Department - Tamil Nadu

40826739 tender for construction of multi purpose building at vanganur villagein vananur panchayat.; 1 construction of multi purpose building at vanganur villagein vananur panchayat. 2 earth work excavation for foundation in all classes of soils and sub soil to full depthexcept in hard rock requiring blasting but inclusive of shoring struttingif required forthe sides of foundation. 3 cement concrete 1:4:8 mix using 40 mm hbg metal for foundaion including watering wherever necessary and laid in layers of not more than 15cm thick. compacting etc., complete complying with standard specifications and as directed. 4 reinforced cement concrete 1:11 / 2:3 using 20mm iss hbg metal including the cost and conveyance of all meterials and cost of all labour charges etc completed, .. belowground level 5 reinforced cement concrete 1:11 / 2:3 using 20mm iss hbg metal including the cost and conveyance of all meterials and cost of all labour charges etc completed, ..above basement level 6 supplying and fabricating and placing in position ms steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and blinding wire all floors etc., complete complying with standard specification. 7 supplying and erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. rate for 10m2 for the following items ( rcc floor slab, roff slab, rectangular / square, tee / ell beams, lintels, below ground level 8 above ground level 9 brick work in cm 1:5 mix using country bricks ground moulded of size 23 x 11 x 7 cm for the following including curing etc., complete complying with standard specifications.below ground level 10 brick work in cm 1:5 mix using country bricks ground moulded of size 23 x 11 x 7 cm for the following including curing etc., complete complying with standard specifications..above basement level 11 ceiling plastering with cement mortar 1:3 mixto 10 mm thick for r.c.c. items including cost and conveyance of all materials to site and all labour charges etc complete 12 plastering cm 1;5 12mm thick including the cost and conveyance of all materials and cost of all labour charges etc., complete. 13 paving the top of roof with solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three crushed stone sand ) 12mm thick and pointed with tile grout ( nitotile grout or equivalent ) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by the executive engineer before use on works ) 14 distempering two coat using oil bound distemper including cost of and conveyance and approved colour paintwith labour charges etc, . 15 painting two coat approved exterior emulsion paint over the plastered surface including cost and conveyance and all other charges etc., 16 painting two coat withready mixed ennemal paint including cost and conveyance and all other charges etc., 17 floor finished with ceramic tiles cm 1:3 mix including cost and conveyance and all other charges etc., 18 dadooing the wall with ceramic tiles cm 1:3 mixincluding cost and conveyance and all other charges etc., 19 supply and fixing of steel door 1.20 x 2.10 m including cost and conveyance and all other charges etc., main door 20 supply and fixing of steel door 0.90 x 2.10 m including cost and conveyance and all other charges etc., toilet door 21 supply and fixing of steel window.90 x 1.30 m including cost and conveyance and all other charges etc., window 22 supply and fixing of light / fan point sd 18 23 supply and fixing ofplug point sd 10 24 supply and fixing of18 amps dpic is 142 25 supply and fixing ofmeter board is 125 26 supply and fixing ofgi service pipe sd 69 27 supply and fixing ofservice main sd 65 28 supply and fixing of18w led tube light 29 supply and fixing ofceilling fan sd 110 30 supply and fixing ofbulk head fitting sd 84 31 supply and fixing of9w cfl bulp 32 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } ( refer clause 13.2 & 13.3 of section 2 of instruction to bidders ( itb ) of sbd ) ...

Rural Development And Panchayats Department - Tamil Nadu

40826441 tender for construction of multi purpose building at vanganur villagein vananur panchayat.; 1 construction of multi purpose building at vanganur villagein vananur panchayat. 2 earth work excavation for foundation in all classes of soils and sub soil to full depthexcept in hard rock requiring blasting but inclusive of shoring struttingif required forthe sides of foundation. 3 cement concrete 1:4:8 mix using 40 mm hbg metal for foundaion including watering wherever necessary and laid in layers of not more than 15cm thick. compacting etc., complete complying with standard specifications and as directed. 4 reinforced cement concrete 1:11 / 2:3 using 20mm iss hbg metal including the cost and conveyance of all meterials and cost of all labour charges etc completed, .. belowground level 5 reinforced cement concrete 1:11 / 2:3 using 20mm iss hbg metal including the cost and conveyance of all meterials and cost of all labour charges etc completed, ..above basement level 6 supplying and fabricating and placing in position ms steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and blinding wire all floors etc., complete complying with standard specification. 7 supplying and erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. rate for 10m2 for the following items ( rcc floor slab, roff slab, rectangular / square, tee / ell beams, lintels, below ground level 8 above ground level 9 brick work in cm 1:5 mix using country bricks ground moulded of size 23 x 11 x 7 cm for the following including curing etc., complete complying with standard specifications.below ground level 10 brick work in cm 1:5 mix using country bricks ground moulded of size 23 x 11 x 7 cm for the following including curing etc., complete complying with standard specifications..above basement level 11 ceiling plastering with cement mortar 1:3 mixto 10 mm thick for r.c.c. items including cost and conveyance of all materials to site and all labour charges etc complete 12 plastering cm 1;5 12mm thick including the cost and conveyance of all materials and cost of all labour charges etc., complete. 13 paving the top of roof with solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three crushed stone sand ) 12mm thick and pointed with tile grout ( nitotile grout or equivalent ) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by the executive engineer before use on works ) 14 distempering two coat using oil bound distemper including cost of and conveyance and approved colour paintwith labour charges etc, . 15 painting two coat approved exterior emulsion paint over the plastered surface including cost and conveyance and all other charges etc., 16 painting two coat withready mixed ennemal paint including cost and conveyance and all other charges etc., 17 floor finished with ceramic tiles cm 1:3 mix including cost and conveyance and all other charges etc., 18 supply and fixing of steel door 1.20 x 2.10 m including cost and conveyance and all other charges etc., main door 19 supply and fixing of rolling shetter 2.30 x 2.10 m including cost and conveyance and all other charges etc., rolling shetter 20 supply and fixing of steel window.90 x 1.20 m including cost and conveyance and all other charges etc., window 21 supply and fixing of light / fan point sd 18 22 supply and fixing ofplug point sd 10 23 supply and fixing of18 amps dpic is 142 24 supply and fixing ofmeter board is 125 25 supply and fixing ofgi service pipe sd 69 26 supply and fixing ofservice main sd 65 27 supply and fixing of18w led tube light 28 supply and fixing ofceilling fan sd 110 29 supply and fixing ofbulk head fitting sd 84 30 supply and fixing of9w cfl bulp 31 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } ( refer clause 13.2 & 13.3 of section 2 of instruction to bidders ( itb ) of sbd ) ...

Rural Development And Panchayats Department - Tamil Nadu

40815606 tender for infra structure 1 work under nnt ( bp ) 2023 24 oddanchatram block tn 05 07; 1. construction ofcommunity hall buillding at komalipatty colony h / o chinnakkampattyestimate amount rs.50.00 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 supplying and filling inbasement with u.s.gravel in layers of not more than 15cm thick well rammed, watered and compacted including cost & conveyance of sand and all labour charges etc., complete as per std. specifications. 6 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below ground level 9 above ground level 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 cement concrete 1:8:16 ( one cement, eight sand and sixteen broken stone jelly ) using 20mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. 13 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 14 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 15 plastering with cement mortar 1:3 mix to 20mm thick including cost and conveyance of all materials & all labour charges etc., complete. 16 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 17 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 18 paving floor with scratch proof ceramic tiles of any colour ofsize 305 x 305 x 6mm, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 19 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 20 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 21 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 22 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 23 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 24 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 25 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 26 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 27 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall building. 28 ( d ) steeldoor of size 1.80 x 2.10m ( double leaf ) 29 ( d1 ) steel door of size 0.90 x 2.10m 30 ( d2 ) steel door of size 1.20 x 2.10m 31 ( d3 ) pvc door of size 0.75 x 2.10m 32 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall building 33 ( w ) steel window of size 1.50m x 1.20m 34 ( w1 ) steel window of size 1.20m x 1.20m 35 ( v ) steel glazed ventilator of size 0.90 x 0.45m 36 labour charges for fixing of doors , windows and rcc jally in position including all labour charges etc., complete 37 steel doors with alongwith frame 38 steel windows and ventilator with alongwith frame 39 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 40 provision for electrification 41 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 42 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 43 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 44 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 45 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 46 supply and fixing of cfl bulb 11w including cost and conveyance of all materials and labour charges etc complete. sd 80 47 supply and fixing of 32 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 48 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 49 eb deposit amount 50 provision for water supply arrangements etc., 51 supply and fixing of 1000 litre hdpe tank 52 63mm pvc pipe 4kg / sqm 53 63mm pvc coupler 54 63mm pvc bend 55 63mm pvc mta 56 solvent cement 57 20mm dia pvc pipe 58 20mm dia pvc coupler 59 20mm dia pvc elbow 60 20mm dia pvc tee 61 20mm dia pvc fta 62 20mm dia gi waste not tap 63 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 64 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 65 provision for sanitary pipe line & dispersion arrangements 66 supplying and fixing pvc ventilating shaft of 110mm dia ( having working pressure 4 kg. / sq.cm ) with 3 metre height including cost of pvc cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers 67 supplying and fixing in position ci manhole covers with ci frames ( heavy duty ) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications 68 110mm dia pvc pipe 4kg / sqm 69 110mm dia pvc elbow 4kg / sqm 70 110mm dia pvc tee 71 towards the cost of providing staircase / ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 72 provision forname board with work detailsincluding cost and conveyance and all labour charges etc., complete 73 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40770838 construction of new anganwadi building at adc colony in uchimalaikuppam panchayat. in chengam block of tiruvannamalai district under pmagy: 2022 23; 1 construction ofnew anganwadi building@ adc colony inuchimalaikuppam panchayat. in chengam block of tiruvannamalai district under pmagy: 2022 23 2 earth work excavation depositing on bank with initial lead and lift as per ss 20 b incl cost and conveyance of all charges etc complete 3 collection and supply of gritty gravel from approved quarry including cost and conveyance of all materials to site including all labour charges for fillingetc.complete, 4 c.c.1:4:8 using 40mm stone jelly including cost and conveyance of all materials to site and cost of labour and all other incidental charges etc., complete. 5 brick work in c.m 1:5 mix using country bricks incuding cost and conveyance and all labour charges etc. 6 brick work in c.m 1:5 mix using country bricks incuding cost and conveyance and all labour charges etc. 7 rcc 1:1.5:3 mix using 20mm metal including cost and conveyance and all labour charges etc. 8 rcc 1:1.5:3 mix using 20mm metal including cost and conveyance and all labour charges etc. 9 supply and erection of centring incl all necessary supports and strutting all cross bracings etc complete column below gl 10 supply and erection of centring incl all necessary supports and strutting all cross bracings etc complete column g.beam 11 supply and fabrication of steel including cost and conveyance and alla labour charges etc. complete. 12 weathering coarse concrete using 20mm size broken brick jelly with in pure slaked lime overthe rcc roof in the proportion of 32 : 12 1 / 2 by volume laid in layer beating the concrete with the wooden batters etc as per standard specifications . 13 finishing the top of roof with one course of pressed tiles conveyance of all materials to site and all labour charges etc complete for 10 sqm 14 plastering with cement mortar 1:5, 12mm thick including cost and conveyance and all labour charges etc. 15 plastering with cement mortar 1:3, 10mm thick including cost and conveyance and all labour charges etc. 16 cement concrete 1:2:4 mix using 20mm iss metal including cost and including cost and conveyance and all labour charges etc, . 17 paving the floor with scratch proof vertified tiles of size 600x600x8mm laid in cm 1;2, 10mm thick and pointing with white cement 0.40kg per sqm mixed with colouring pigment to siut thecolour of the tilesincludingcost and conveyance of all materials to site and all labour charges etc complete 18 paving the floor with scratch proof anti skilled tiles of size 600x600x8mm laid in cm 1;2, 10mm thick and pointing with white cement 0.40kg per sqm mixed with colouring pigment to siut thecolour of the tilesincludingcost and conveyance of all materials to site and all labour charges etc complete 19 paving the floor with scratch proof ceramic tiles of size 600x600x8mm laid in cm 1;2, 10mm thick and pointing with white cement 0.40kg per sqm mixed with colouring pigment to siut thecolour of the tilesincludingcost and conveyance of all materials to site and all labour charges etc complete 20 dadooing of walls with colour glazed tiles of size 300x200x6 mmof best quality including cost and conveyance of all materials to site and all labour charges etccomplete. 21 towards the cost of steel door of size1.00 mx2.10 m including all charges etc. 22 towards the cost of steel door of size0.75 mx2.10 m including all charges etc. 23 towards the cost of steel door of size1.10 mx2.10 m including all charges etc. 24 towards the cost of steel ventilator of size 0.9x0.45 m including all charges etc. 25 towards the cost of steel window of size1.20mx1.30 m including all charges etc. 26 towards the cost of steel window of size1.50mx1.60m including all charges etc. 27 towards cost and fixing of rcc jolly of size 0.90x0.45m including cost and conveyance and labour for fixing etc 28 paintingtwo coatwith approved quality ofdistemper with colour over one coat of white cement forprimier coat for the base including preparing surface and all materials cost labour etc 29 painting two coatwith ready mixedplastic emulsion of firstquality paint and of approved colour over apriming coatincluding thorogh scarpping clean removal of dirt etc complete. 30 painting two coats using ist quality readymix enamel paint of approved colour over new iron work including cost and conveyance and all labour charges etc. 31 light point ( sd20 ) 32 fan point ( sd20 ) 33 fan ( sd112 ) 34 plug point ( sd38 ) 35 cfl lamp ( sd80 ) 36 tube light fittings ( sd 88 ) 37 dpi swtich of 500 v ( sd142 ) 38 g i pipe ( sd69 ) 39 service wire ( sd64 ) 40 bulk head fitting ( sd83 ) 41 500 lt ank 42 25 mm upvc pipe 43 25 mm upvc elbow 44 25 mm upvc bend 45 25 mm upvc tee 46 110 mm pvc pipe 47 110 mm pvc tee 48 110 mm pvc elbow 49 15 mm diacp down pipe 50 cost & supply for baby w.c including cost and conveyance ofall materials to work site and labor charges etc complete. 51 cost & supply for e w.c including cost and conveyance ofall materials to work site and labor charges etc complete. 52 cost & supply for urinalincluding cost and conveyance ofall materials to work site and labor charges etc complete. 53 cost & supply for hand basinincluding cost and conveyance ofall materials to work site and labor charges etc complete. 54 cost & supply of cudappah slab including cost and conveyance ofall materials to work site and labor charges etc complete. 55 supplying and fixing pvc rain water down fall pipes of following dia meter etc., complete. 56 provision forrain water harwesting pit arrangements 57 provision forcitizen informantion board 58 provision forhand rail for ss works 59 provision forlock & key 60 provision ofpainting cartoons in hall and toilet & letters, pictures & board, etc. 61 e b deposit 62 provision for photo 63 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40755080 tender for infra structure 1 works under sfc ( dp ) 2023 24 oddanchatram block tn 05 01; 1. construction of rural library buildingat javadupattyh / ojavadupatty. estimate amount rs.14.00 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 6 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below gl 9 above gl 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 13 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 14 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 15 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 10 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 16 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 17 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 18 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 19 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20 mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed 20 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 21 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 22 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 23 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 24 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer fo rlibrary building. 25 ( d ) steeldoor of size 1.20 x 2.10m ( double leaf ) 26 ( d1 ) steel door of size 0.75 x 1.80m 27 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for library building 28 ( w ) steel window of size 1.80m x 1.30m 29 towards supply and delivery of rcc jallyas per std. specification 30 rcc jally of size 0.60 x 0.45m 31 labour charges for fixing of doors , windows and ventilator including all etc., complete 32 doors 33 windows 34 supply and fixing of cuddapah slab of 20 / 30mm thick for shelf arrangements including cost and conveyace of all materials to site and all labour charges etc complete 35 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 36 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 37 provision for water supply arrangements etc., 38 supply and fixing of 1000 litre hdpe tank 39 63mm pvc pipe 4kg / sqm 40 63mm pvc coupler 41 63mm pvc bend 42 63mm pvc mta 43 solvent cement 44 20mm dia pvc pipe 45 20mm dia pvc coupler 46 20mm dia pvc elbow 47 20mm dia pvc tee 48 20mm dia pvc fta 49 20mm dia gi waste not tap 50 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 51 provision for sanitary pipe line & dispersion arrangements including all charges etc., complete 52 110mm dia pvc pipe 4kg / sqm 53 110mm dia pvc elbow 54 provision for electrification 55 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 56 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 57 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 58 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 59 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 60 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 61 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 62 eb deposit amount 63 leach pit 64 manufacturing, supplying of 1200mm dia precast reinforced cement concrete ring of 20 30mm thickness with 300mm hieght in rcc 1:1.5:3, using 10 12mm hbgs jelly including cost of reinforcement steel in position and cost of moulding charges, casting of ring, finishing, curingetc., complete complying with standard specification and as directed by the departmental officers 65 manufacturing, supplying of 1300mm dia precast reinforced cement concrete slab of 40 50mm thickness in rcc 1:1.5:3, using 10 12mm hbgs jelly including cost of reinforcement steel in position and cost of moulding charges, casting of ring, finishing, curingetc., complete complying with standard specification and as directed by the departmental officers 66 provision for rain water harvesting structureincluding cost and conveyance of all materials and all labour charges etc., complete 67 towards the cost of providing ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 68 provision forname board with work details and information boardincluding cost and conveyance and all labour charges etc., complete 69 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Municipal Adminitration And Water Supply Department - Tamil Nadu

40737221 tender for maintenance repairs to corporation elementary school building at rail nagar in ward no 36; 1 earth work excavation for foundation in ordinary soil with initial lead and lift etc., complete as per standard specification ( narrow excavation ) 2 supplying and filling in foundation andbasement with m.sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification. 3 plain cement concrete 1:5:10 mix ( one cement five m.sand and ten aggregate ) using 40mm size iss gauge hbbg metal including mixing, laying, consolidating, curing, cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification 4 centering for soffits of rcc slabs of plane surface like lintels, beams , etc., including strutting 3m high using mild steel sheets of size 90cm x60cm x and b.g 10 stiffened with m.s angles of size 25mm x 25mm x 3mm laid over silver oak ( c.w ) joists of size 10cm x 6.5cm ( spaced at about 90cm c / c ) and supported dy casurina props of 10cm to 13cm dia ( spaced of 75cm c / c ) complying with standard specification 5 a ) with out shuttering 6 b ) with shuttering 7 plain cement concrete 1:2:4 ( one cement, two m sand and four aggregates ) mix using 20mm iss gauge hbbg metal including curing cost of materials and all labour charges and curing etc., complete. 8 laying the flooring with granoythic flooring 25mm thick of approved make and quality and 25mm laser plastering and pointing etc complete 9 supplying, cutting, bending, tying and fixing in position mild steel and rts grills for reinforced cement concrete works including cost of steel and binding wire etc., complete 10 reinforced cement concrete 1:1.5:3 mixusing 20mm iss gauge hbbg metal from the approved quarry including mixing, laying, consolidating, curing cost and conveyance of all materials to site and all labourcharges etc., complete as per standard specification for foundation and basement. ( using m.sand ) 11 for foundation 12 for superstructure 13 brick work in cm 1:5 ( one cement & five sand ) using ii class ground moulded bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 including finishing, curing, etc., complete complying with standard specification ( for foundation basement ) ( using m.sand ) 14 brick work in cm 1:5 ( one cement & five sand ) using ii class ground moulded bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 including finishing, curing, etc., complete complying with standard specification ( for super structure ) ( using m.sand ) 15 supply and collection of coarse gravel including cost of conveyance from approved quarry to site and stacking to the departmental metric gauge for taking pre measurement to departmental officers etc., complete 16 special ceiling plastering with cement mortar ( 1:3 ) 10mm , thick including cost and conveyance of all materilas to site and labour charges etc, completeusing m.sand 17 plastering with cement mortar ( 1:5 ) 12mm , thick in all floors including cost and conveyance of all materilas to site and labour charges etc, completeusing m.sand 18 supply and fixing in position of white glazed indian oriyan type water closet of size 580x440mm with s or p trap and a pair of foot rest to shape set in brick jelly cement concrete 1:4:8mix, 100mm tk using 20mm iss gauge brick jelly and finished to slope without any leakage and defects etc., excluding cost of water closet s or p trap and foot rest complete 19 supplying and fixing in positio european water loset of size 580 x 440 mm white glazed earthen ware of approved quality with p trap or s trap contiming to iss 2556 part xii with sand cushion and forming fiocring around the closet using 40mm broken brick jelly in line oncrete 1:2:5 lane part of time two parts of sand five ports without leakage etc., complete complying with standard specifictions and as directed by the departmental officers 20 supply and fixing of gi sheet door of sizes 0.70 x 2.00m and 0.90x2.10m framed alround ms angle iron of size 30 x 30 x 5mm with one ledge and two braces made out of ms flat 30 x 5mm size without door frame hot with necessary kudjun pins and locking arrangements on both sides complete. the bwg gi plain sheet should cover the me angle frame alround in such a way that there would not be any exposed of the angles to frame must be with aluminum rivets @ 25cm etc, . the entire shutter door must be painted with one coat of rod oxide paint and the shutter properly fixed in position etc., complete. 21 manufacturing, supplying & fixing in position steel windows of ms sheet 20 gauge thick with openable shutter frame and shutter frame made out of steel section confirming to is 7452 / 1990.the outer frames of windows made ofz section ( f7d ) of size 25 x 20 x 3 mm confirming to is7452 / 1992 mullions are made of ( f4b ) of section size 46x25x3mm confirming to is7452 / 1990.the shutters are individual and each of them can be operated separately. sash bars are made of tsection ( t2 ) of size 25x22x3m, 2nos of sturdy hinges and one numbers of handle cum slatch of special type are fixedfor with openable shutter. suitable opening is left for its any operation. one number of adjustable stay with locking bracketof sufficient length shall be provided for each shutter 4 nos. of 40x40x3mm anngle hold fast 230mm length are welded to the outer frame at appropriate point.m.s square bars of 12mm size is welded to the inner face of the window at equal intervals not excluding 10cm spacings , 20gauge ms sheet is used for covering the shutter. grill members are painted with one coat of primer. also rate is inclusive of costof all materials, labour charges for fixing, one coat of primer, welding charges transportations to the work site, loading unloading and all other incidental charges etc., complete. 22 rcc 1:2:4mix for jally 5cm thick of approved design using 20mm iss gauge hbbg chips excluding cost of reinforcement grills in position but including moulding, casting, finishing and fixing in position etc., complete 23 construction of inspection chamber of size 1’ 1 ½” x 1’ 1 ½” as per t.p.no.18 / 1944 and of the description the foundation of the inspection chamber to be cement concrete 1:5:10 mix using 40mm metal and brick work in cement mortar 1:5 mix using country bricks and plastering with cement mortar 1:4 mix 12mm tk as per std. specification. 24 flooring with ceramic tiles white color ceramic tiles of size 305 x 305 x 6mm with self bath way special color tiles in cement mortar 1:3 mix 10mm thick and pointing with white cement using at the rate of 0.45 kg / cm2 including finishing the joint neatly pointing flush with tiles surface etc., complete 25 laying the flooring withanti skid coloured ceramic tiles of sizes 305mm x305mm x 6mm size of approved make and quality and colour l set in cement mortar 1:3 ( one cement , three sand ) over 20 mm base layer plastering and pointing with white cement neatly as directed. 26 dadooing the skirting the wall with white ( or ) colour ceramic tiles of size 20cm x 20cm x 6mm first quality design ceramic tiles of all colors laid in cement mortar 1:2 mix – 10mm tk. and pointing with white cement using 0.40kg. / m2 including finishing the joint and pointing flush with tiles surface etc., complete. 27 virtified marbonite sahabad tiles of size 600 x 600 x 8 mm of approved colour quality of required size etc., complete 28 supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 125gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the dept. engineer before use on work 29 supplying & fixingdoor shutters for mediun density fiber board of exterior grade 35 mm thick, single leaf conforming to is:12406 / 1989 with 35x12 mm t.w.lipping on all edges with necessary adhesives and cp screws complying with standard specifications. the rate is inclusive ofthreee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos, 200mm towerbolt i no. 300mm aldrop 1 no. alu handle ornamental type 2 nos, and 1 no. door stopper etc complete. 30 supply and fixing ms grill windows and vendilators including one coat of primer including cost of materials and laboure charges etc complete. 31 weathering course with concrete broken brick ( s.i.no.278 ) & ( p & d ) data 54.jelly 20mm gauge in pure slaked lime ( no sand to be added ) over roof slab, the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete 32 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete. 33 supply and fixing of following water supply materials at site with best quality etc complete 34 20mm dia gi pipe b class ( external below gl open ) 35 15mm dia gi pipe b class ( external below gl open ) 36 20mm dia gi coupling 37 15mm dia gi coupling 38 20mm dia gi elbow 39 15mm dia gi elbow 40 20mm dia gi union 41 20mm dia gm gate valve 42 15mm dia pvc screwdown tap 43 pvc tank 44 supplyof follwing water supply materials at site with best quality etc complete 45 110mm dia pvc pipe 6ksc 46 110mm dia pvc elbow 47 110mm dia pvc tee 48 pvc adhesive 49 conveyance of 110mm, 90mm dia pvc pipes and specials laying to proper grade and alinment jointing with pvc couplers with cement paste etc., complete. ( as per standard specification ) 50 110mm , 90mm dia pvc 6ksc pipe 51 wiring with 2 x 1.5 sqmm ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 3mm thick hylum sheet cover with tw switch box and 5a f.t. switch with continuous earth wire connection of 14 swg tc wire for making good of the concealed portion with suitable colour for pvc concealed light point / fan point ( for electronic regulator ) . etc, complete as per standard specifications. sd 24 52 supply and fixing of single box type 440w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceilig with flu tube with pvc unsheather copper leads from terminals sd ( 88 ) 53 supply and fixing of 1200mm ( 48 ) ac ceiling fan complete stepped electronic 300w regulator with 1m down rod on the existing clamp ( sd no.107 ) 54 white washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification 55 painting two coats with ready mixed plastic emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete 56 painting two coats with ready mixed enamel paint over the old iron works of approved quality and colour without priming coatincluding the cost all materials etc., complete, 57 painting two coats with ready mixed enamel paint over the new wooden works of approved quality and colour without priming coatincluding the cost all materials etc., complete, 58 painting with black board paint two coatsof approved quality and colour without priming coatincluding the cost all materials etc., complete, 59 supplying and fixing inposition of ms hollow section work including cost of cutting and welding charges with one coat of redoxide priming etc.complete. 60 supplying and fixing inposition of pvc painted galvanium sheet corrugated roofing with 0.47mm thick frb sheetwith painted coat lncluding cost of bolt, nut and washer etc.complete....

Rural Development And Panchayats Department - Tamil Nadu

40719340 tender for construction of new anganwadi buidling at kolakudi panchayat; 1 construction ofnew anganwadibuilding @ kolakudi panchayat 2 earthwork excavation and depositing on bank with initial lead and lift in hard stiff clay soil and hard gravel soil as per standard specification ss 20 b for narrow foundation 3 collection and supply of gravel from approved quarry including cost and conveyance of all materials to site including all labour charges for fillingetc.complete, 4 base course concrete with c.c.1:4:8 mix using 40mm i.s.s. size hbg metal from approved quarry to work site including cost and conveyance of all materials and labour charges for mixing for base course as per standared specification. 5 brick work in c.m 1:5 mix using country bricks incuding cost and conveyance and all labour charges etc. 6 brick work in c.m 1:5 mix using country bricks incuding cost and conveyance and all labour charges etc. 7 rcc 1:1.5:3 mix using 20mm metal including cost and conveyance and all labour charges etc. 8 rcc 1:1.5:3 mix using 20mm metal including cost and conveyance and all labour charges etc. 9 supplying and errecting centering for sides and soffits including supports and strutting up to 3.29m. height for plain surfaces including strutting. 10 supplying and errecting centering for sides and soffits including supports and strutting up to 3.29m. height for plain surfaces including strutting. 11 supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all r.c.c works. 12 weathering coarse concrete using 20mm size broken brick jelly with in pure slaked lime overthe rcc roof in the proportion of 32 : 12 1/2 by volume laid in layer beating the concrete with the wooden batters etc as per standard specifications . 13 finishing the top of roof with one course of pressed tiles conveyance of all materials to site and all labour charges etc complete for 10 sqm 14 plastering with cement mortar 1:5, 12mm thick including cost and conveyance and all labour charges etc. 15 plastering with cement mortar 1:3, 10mm thick including cost and conveyance and all labour charges etc. 16 cement concrete 1:2:4 mix using 20mm iss metal including cost and including cost and conveyance and all labour charges etc,. 17 paving the floor with scratch proof vertified tiles of size 600x600x8mm laid in cm 1;2,10mm thick and pointing with white cement 0.40kg per sqm mixed with colouring pigment to siut thecolour of the tilesincludingcost and conveyance of all materials to site and all labour charges etc complete 18 paving the floor with pre polished concrete anti skid tiles (required shape and design) of 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three crushed stone m.sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.(the make and brand of the tiles should be got approved by executive engineer before use on works)using anti skid tiles (observed data) 19 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (one cement and threem.sand)base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. 20 dadooing walls with following best approved quality, white / colour glazed tiles of following sizes 150mmx 150mmx 6mm set in cement mortar 1:2 (one cement and two crushed stone m.sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., 21 towards the cost of steel door of size.9 mx2.4m including all charges etc. 22 towards the cost of steel door of size 0.75mx1.5 m including all charges etc. 23 towards the cost of steel door of size 1.10mx2.4 m including all charges etc 24 towards the cost of steel ventilator of size 0.9x0.45 m including all charges etc. 25 towards the cost of steel window of size 1.8m*1.6m including all charges 26 towards the cost of steel window of size1.5mx1.6 m including all charges etc. 27 towards cost and fixing of rcc jolly of size 0.90x0.45m including cost and conveyance and labour for fixing etc 28 paintingtwo coatwith approved quality ofdistemper with colour over one coat of white cement forprimier coat for the base including preparing surface and all materials cost labour etc 29 painting two coatwith ready mixedplastic emulsion of firstquality paint and of approved colour over apriming coatincluding thorogh scarpping clean removal of dirt etc complete. 30 painting two coats using ist quality readymix enamel paint of approved colour over new iron work including cost and conveyance and all labour charges etc. 31 light pointsd20 32 fanpointsd20 33 fan point sd110 34 plug point (sd36) 35 cfl lamp (sd80) 36 tube light fittings ( sd 88 ) 37 dpi swtich of 500 v(sd142) 38 g i pipe (sd69) 39 service wire (sd64) 40 bulk head fitting (sd83) 41 500 lit tank 42 25mm upvc pipe 43 25mm upvc elbow 44 25mm upvc bend 45 25 mm upvc tee 46 110 mm pvc pipe 6ksc 47 110mm pvc tee 48 110mm pvc elbow 49 15 mm diacp down tap 50 cost & supply for baby w.c including cost and conveyance ofall materials to work site and labor charges etc complete. 51 cost & supply for e w.c including cost and conveyance ofall materials to work site and labor charges etc complete. 52 cost & supply for flat black urinal trap including cost and conveyance ofall materials to work site and labor charges etc complete. 53 supplying and fixing in position best quality and approved make indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass cp pillar tap, 32mm dia b class gi waste pipe with rubber plug and chain, 15mm dia gm wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia cp brass waste coupling including fixing of wash basin using ci brackets on to the wall in position with tw plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (the wash hand basin and specials should be got approved by the executive engineer before use on works). 54 cost & supply of cudappah slab including cost and conveyance ofall materials to work site and labor charges etc complete. 55 supplying and fixing pvc rain water down fall pipes of following dia meter etc., complete. 56 provision forrain water harwesting pit arrangements 57 provision for name board 58 provision forhand rail for ss works 59 provision forlock & key 60 provision ofpainting cartoons in hall and toilet & letters, pictures & board, etc. 61 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package} ...

Rural Development And Panchayats Department - Tamil Nadu

40661136 tender for construction of community hall buillding at komalipatty colony house of chinnakkampatty.; 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 supplying and filling inbasement with u.s.gravel in layers of not more than 15cm thick well rammed, watered and compacted including cost & conveyance of sand and all labour charges etc., complete as per std. specifications. 6 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below ground level 9 above ground level 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 cement concrete 1:8:16 ( one cement, eight sand and sixteen broken stone jelly ) using 20mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. 13 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 14 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 15 plastering with cement mortar 1:3 mix to 20mm thick including cost and conveyance of all materials & all labour charges etc., complete. 16 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 17 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 18 paving floor with scratch proof ceramic tiles of any colour ofsize 305 x 305 x 6mm, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 19 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 20 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 21 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 22 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 23 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 24 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 25 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 26 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 27 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall building. 28 ( d ) steeldoor of size 1.80 x 2.10m ( double leaf ) 29 ( d1 ) steel door of size 0.90 x 2.10m 30 ( d2 ) steel door of size 1.20 x 2.10m 31 ( d3 ) pvc door of size 0.75 x 2.10m 32 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall building 33 ( w ) steel window of size 1.50m x 1.20m 34 ( w1 ) steel window of size 1.20m x 1.20m 35 ( v ) steel glazed ventilator of size 0.90 x 0.45m 36 labour charges for fixing of doors , windows and rcc jally in position including all labour charges etc., complete 37 steel doors with alongwith frame 38 steel windows and ventilator with alongwith frame 39 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 40 provision for electrification 41 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 42 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 43 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 44 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 45 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 46 supply and fixing of cfl bulb 11w including cost and conveyance of all materials and labour charges etc complete. sd 80 47 supply and fixing of 32 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 48 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 49 eb deposit amount 50 provision for water supply arrangements etc., 51 supply and fixing of 1000 litre hdpe tank 52 63mm pvc pipe 4kg / sqm 53 63mm pvc coupler 54 63mm pvc bend 55 63mm pvc mta 56 solvent cement 57 20mm dia pvc pipe 58 20mm dia pvc coupler 59 20mm dia pvc elbow 60 20mm dia pvc tee 61 20mm dia pvc fta 62 20mm dia gi waste not tap 63 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 64 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 65 provision for sanitary pipe line & dispersion arrangements 66 supplying and fixing pvc ventilating shaft of 110mm dia ( having working pressure 4 kg. / sq.cm ) with 3 metre height including cost of pvc cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers 67 supplying and fixing in position ci manhole covers with ci frames ( heavy duty ) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications 68 110mm dia pvc pipe 4kg / sqm 69 110mm dia pvc elbow 4kg / sqm 70 110mm dia pvc tee 71 towards the cost of providing staircase / ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 72 provision forname board with work detailsincluding cost and conveyance and all labour charges etc., complete 73 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 74 2. construction ofcommunity hall buillding at naranappanayakkanpattyh / o chinnakkampatty.estimate amount rs.30.00 lakhs 75 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 76 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 77 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 78 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 79 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 80 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 81 below ground level 82 above ground level 83 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 84 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 85 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 86 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 87 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 88 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 89 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 90 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 91 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 92 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 93 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 94 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall building. 95 ( d ) steeldoor of size 1.80 x 2.10m ( double leaf ) 96 ( d1 ) steel door of size 0.90 x 2.10m 97 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall building 98 ( w ) steel window of size 1.50m x 1.20m 99 ( w1 ) steel window of size 0.90m x 1.20m 100 ( v ) steel glazed ventilator of size 0.90 x 0.45m 101 labour charges for fixing of doors , windows and rcc jally in position including all labour charges etc., complete 102 steel doors with alongwith frame 103 steel windows and ventilator with alongwith frame 104 supply and fixing of cuddapah slab of 20 / 30mm thick for shelf arrangements including cost and conveyace of all materials to site and all labour charges etc complete 105 provision for electrification 106 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 107 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 108 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 109 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 110 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 111 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 112 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 113 eb deposit amount 114 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 115 towards the cost of providing staircase / ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 116 provision forname board in with work detailsincluding cost and conveyance and all labour charges etc., complete 117 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40661125 infra structure1 works under nnt ( bp ) 2023 24 oddanchatram block tn 05 04; 1. construction ofcommunity hall buillding at elanthariyur h / o puliyur natham.estimate amount rs.30.00 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 6 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below ground level 9 above ground level 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 13 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 14 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 15 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 16 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 17 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 18 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 19 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 20 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 21 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall building. 22 ( d ) steeldoor of size 1.80 x 2.10m ( double leaf ) 23 ( d1 ) steel door of size 0.90 x 2.10m 24 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall building 25 ( w ) steel window of size 1.50m x 1.20m 26 ( w1 ) steel window of size 0.90m x 1.20m 27 ( v ) steel glazed ventilator of size 0.90 x 0.45m 28 labour charges for fixing of doors , windows and rcc jally in position including all labour charges etc., complete 29 steel doors with alongwith frame 30 steel windows and ventilator with alongwith frame 31 supply and fixing of cuddapah slab of 20 / 30mm thick for shelf arrangements including cost and conveyace of all materials to site and all labour charges etc complete 32 provision for electrification 33 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 34 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 35 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 36 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 37 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 38 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 39 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 40 eb deposit amount 41 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 42 towards the cost of providing staircase / ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 43 provision forname board in with work detailsincluding cost and conveyance and all labour charges etc., complete 44 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40661121 tender for infra structure1 works under nnt ( bp ) 2023 24 oddanchatram block tn 05 05; 1. construction ofcommunity hall buillding at edaiyakottai adcolony h / o edaiyakottai.estimate amount rs.50.00 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 supplying and filling inbasement with u.s.gravel in layers of not more than 15cm thick well rammed, watered and compacted including cost & conveyance of sand and all labour charges etc., complete as per std. specifications. 6 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below ground level 9 above ground level 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 cement concrete 1:8:16 ( one cement, eight sand and sixteen broken stone jelly ) using 20mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. 13 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 14 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 15 plastering with cement mortar 1:3 mix to 20mm thick including cost and conveyance of all materials & all labour charges etc., complete. 16 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 17 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 18 paving floor with scratch proof ceramic tiles of any colour ofsize 305 x 305 x 6mm, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 19 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 20 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 21 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 22 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 23 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 24 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 25 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 26 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 27 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall building. 28 ( d ) steeldoor of size 1.80 x 2.10m ( double leaf ) 29 ( d1 ) steel door of size 0.90 x 2.10m 30 ( d2 ) steel door of size 1.20 x 2.10m 31 ( d3 ) pvc door of size 0.75 x 2.10m 32 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall building 33 ( w ) steel window of size 1.50m x 1.20m 34 ( w1 ) steel window of size 1.20m x 1.20m 35 ( v ) steel glazed ventilator of size 0.90 x 0.45m 36 labour charges for fixing of doors , windows and rcc jally in position including all labour charges etc., complete 37 steel doors with alongwith frame 38 steel windows and ventilator with alongwith frame 39 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 40 provision for electrification 41 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 42 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 43 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 44 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 45 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 46 supply and fixing of cfl bulb 11w including cost and conveyance of all materials and labour charges etc complete. sd 80 47 supply and fixing of 32 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 48 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 49 eb deposit amount 50 provision for water supply arrangements etc., 51 supply and fixing of 1000 litre hdpe tank 52 63mm pvc pipe 4kg / sqm 53 63mm pvc coupler 54 63mm pvc bend 55 63mm pvc mta 56 solvent cement 57 20mm dia pvc pipe 58 20mm dia pvc coupler 59 20mm dia pvc elbow 60 20mm dia pvc tee 61 20mm dia pvc fta 62 20mm dia gi waste not tap 63 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 64 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 65 provision for sanitary pipe line & dispersion arrangements 66 supplying and fixing pvc ventilating shaft of 110mm dia ( having working pressure 4 kg. / sq.cm ) with 3 metre height including cost of pvc cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers 67 supplying and fixing in position ci manhole covers with ci frames ( heavy duty ) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications 68 110mm dia pvc pipe 4kg / sqm 69 110mm dia pvc elbow 4kg / sqm 70 110mm dia pvc tee 71 towards the cost of providing staircase / ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 72 provision forname board with work detailsincluding cost and conveyance and all labour charges etc., complete 73 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40660969 tender for infra structure 3 works under nnt ( bp ) 2023 24 oddanchatram block tn 05 06; 1. construction ofcommunity hall buillding at parumarathupatty ad colony h / o javadupatty.estimate amount rs.20.00 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 6 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below gl 9 above gl 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 13 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 14 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 15 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 16 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 17 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20 mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed 18 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 19 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 20 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 21 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 22 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall. 23 doorof size 1.80x 2.10m 24 doorof size 1.50x 2.10m 25 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall. 26 steel windowof size 1.50m x 1.20m 27 towards supply and delivery of new steel ventilatoras per std. specification 28 n type steel glazed ventilator of size 1.20 x 0.60m 29 labour charges for fixing of doors , windows and ventilator including all etc., complete 30 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 31 provision for water supply arrangements etc., 32 supply and fixing of 1000 litre hdpe tank 33 63mm pvc pipe 4kg / sqm 34 63mm pvc coupler 35 63mm pvc bend 36 63mm pvc mta 37 solvent cement 38 20mm dia pvc pipe 39 20mm dia pvc coupler 40 20mm dia pvc elbow 41 20mm dia pvc tee 42 20mm dia pvc fta 43 20mm dia gi waste not tap 44 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 45 provision for electrification 46 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 47 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 48 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 49 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 50 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 51 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 52 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 53 eb deposit amount 54 provisions for ramp with hand rail arrangements 55 provision for name board 56 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 57 2. construction ofcommunity hall buillding at javadupatty north ad colony h / o javadupatty.estimate amount rs.20.00 lakhs 58 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 59 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 60 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 61 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 62 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 63 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 64 below gl 65 above gl 66 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 67 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 68 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 69 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 70 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 71 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 72 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 73 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20 mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed 74 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 75 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 76 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 77 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 78 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall. 79 doorof size 1.80x 2.10m 80 doorof size 1.50x 2.10m 81 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall. 82 steel windowof size 1.50m x 1.20m 83 towards supply and delivery of new steel ventilatoras per std. specification 84 n type steel glazed ventilator of size 1.20 x 0.60m 85 labour charges for fixing of doors , windows and ventilator including all etc., complete 86 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 87 provision for water supply arrangements etc., 88 supply and fixing of 1000 litre hdpe tank 89 63mm pvc pipe 4kg / sqm 90 63mm pvc coupler 91 63mm pvc bend 92 63mm pvc mta 93 solvent cement 94 20mm dia pvc pipe 95 20mm dia pvc coupler 96 20mm dia pvc elbow 97 20mm dia pvc tee 98 20mm dia pvc fta 99 20mm dia gi waste not tap 100 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 101 provision for electrification 102 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 103 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 104 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 105 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 106 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 107 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 108 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 109 eb deposit amount 110 provisions for ramp with hand rail arrangements 111 provision for name board 112 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 113 3. construction ofcommunity hall buillding at javadupatty east ad colony h / o javadupatty.estimate amount rs.20.00 lakhs 114 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 115 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 116 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 117 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 118 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 119 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 120 below gl 121 above gl 122 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 123 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 124 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 125 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 126 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 127 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 128 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 129 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20 mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed 130 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 131 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 132 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 133 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 134 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall. 135 doorof size 1.80x 2.10m 136 doorof size 1.50x 2.10m 137 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall. 138 steel windowof size 1.50m x 1.20m 139 towards supply and delivery of new steel ventilatoras per std. specification 140 n type steel glazed ventilator of size 1.20 x 0.60m 141 labour charges for fixing of doors , windows and ventilator including all etc., complete 142 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 143 provision for water supply arrangements etc., 144 supply and fixing of 1000 litre hdpe tank 145 63mm pvc pipe 4kg / sqm 146 63mm pvc coupler 147 63mm pvc bend 148 63mm pvc mta 149 solvent cement 150 20mm dia pvc pipe 151 20mm dia pvc coupler 152 20mm dia pvc elbow 153 20mm dia pvc tee 154 20mm dia pvc fta 155 20mm dia gi waste not tap 156 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 157 provision for electrification 158 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 159 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 160 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 161 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 162 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 163 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 164 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 165 eb deposit amount 166 provisions for ramp with hand rail arrangements 167 provision for name board 168 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Municipal Adminitration And Water Supply Department - Tamil Nadu

40646090 tender for repairs and maintenance to the pavadi elementary school in division no. 41; 1 dismantaling the damaged brick work in cement mortor including all cost etc complete. 2 chipping the damaged ceiling plastering including all cost etc complete. 3 dismantaling the damaged pressed tiles & weathering course over roof including all cost and conveyance etc ( s.i. no.38b ) 4 earth work excavation for foundation in ordinary soil, light black cotton sandy loam and dry silt including shoring, strutting, baling or pumping out water wherever necessary and refilling the sides of foundation with excavated earth in layers of 15cm thick and depositing the surplus earth at places as directed by the departmental officers with initial lead and lift 5 narrow foundation 6 open foundation 7 plain cement concrete 1:4:8 mix ( one cement four m sand and eight aggregate ) using 40mm size iss gauge hbbg metal including mixing, laying, consolidating, curing, cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification 8 supplying and errecting centering to sides and soffits including supports and struttingfor drainage sides andculvert body wall sidesusing m.s sheets of size90cm x 60cm and b.g 10stifenedwith welded mild steel angles of size 25mm x 25mm x 3mm for boardinglaid over ( silver oak joists ) of size 10cm x 6.50cm spread at about 90cm including all labour charges and cost and conveyance of all materials to site etc. complete complying with standard specification 9 forcolumn 10 grade beam 11 reinforced cement concrete 1:1½:3 mix ( one cement one and half m sand three aggregate ) using 20mm iss gauge hbbg metal from the approved quarry including mixing, laying, consolidating, curing cost and conveyance of all materials to site and all labourcharges etc., complete as per standard specification 12 up tobasement 13 above basement 14 brick work in cement mortar 1:5 mix using fly ash bricks of 230x110x70mm ( 8 3 / 4 x 41 / 4 x 23 / 4 ) from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications 15 supply and fabrication and placing in position of tmt steel roads to required size and length as directed by the departmental officers including cost of binding wire, cutting, bending and tying with proper position etc., including cost and conveyance of all materials to site and all labour chargesetc., complete complying with standard specification 16 plastering with cement mortar 1:5 mix, 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications 17 strucco plastering 12mm thick using hbbg chips of size 10mm and below over a base plastering with cement mortar 1:5 mix, 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications 18 fabricating supply and fixing and position of ms doors with single leave. the door outer frame will be 40x40x6mm ms angle, the shutter frame will be 35x35x6 mm, ms angle intermediate stiffner will be 35x35x6 mm with cross stiffner 25x 25x5 mm flats covered with 18 gauge m.s. sheet with necessary hinges, tower bolts, aldrop length 30mm and hold fast etc., complete with one coat red oxideprimer. 19 fabricating supply and fixing and position of ms doors with double leave made out of 18 gauge m.s. sheet, outer frame 35x35x5mm angle, inner frame 25x25x5mm angle, cross stiffner with ms flat 25x5mm, altrop tower bolts 2 nos. two handles and six holdfasts completed welded and rivetted and one coat of red oxide painting including cost of all materials and labour etc., complete 20 manufacturing, supplying & fixing in position steel windows of ms sheet 20 gauge thick with openable shutter frame and shutter frame made out of steel section confirming to is 7452 / 1990.the outer frames of windows made ofz section ( f7d ) of size 25 x 20 x 3 mm confirming to is7452 / 1992 mullions are made of ( f4b ) of section size 46x25x3mm confirming to is7452 / 1990.the shutters are individual and each of them can be operated separately. sash bars are made of tsection ( t2 ) of size 25x22x3m, 2nos of sturdy hinges and one numbers of handle cum slatch of special type are fixedfor with openable shutter. suitable opening is left for its any operation. one number of adjustable stay with locking bracketof sufficient length shall be provided for each shutter 4 nos. of 40x40x3mm anngle hold fast 230mm length are welded to the outer frame at appropriate point.m.s square bars of 12mm size is welded to the inner face of the window at equal intervals not excluding 10cm spacings , 20gauge ms sheet is used for covering the shutter. grill members are painted with one coat of primer. 21 collection, supply and filling ofwell gravel from approved quarry to work site and stocking to the departmental gauge for premeasurement as directed by the departmental engineer, to required depth not more than 15cm depth including cost andconveyance ofgravel to site and all labour charges for filling etc., complete complying with standard specification 22 weathering course with concrete broken brick jelly 20mm size in pure slaked lime ( no sand to be used ) over rcc roof slab the proportion of broken brick jelly to lime being 32:12.5 well beaten with wooden beaters giving required slopes and thicknessetc., complete 23 finishing the top with solar reflectiv ceramic tiles of size 300 mm x 300mm x 7mm size laid in cm 1:3 mix mixed with water proofing compound as per indian standard 2% by weight of cement used and pointed with the same mortar etc., complete 24 special ceiling plastering for rc slabs and beams with cement mortar 1:3 mix 10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications 25 plastering with cement mortar 1:3 mix, 20mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications 26 flooring with first quality plain ceramic tiles of approved colour and quality of size 305mm x 305mm x 6mm laid in cement mortar 1:3 mix, 20mm thick and pointing with the same mortar etc., completely and finish very neatly 27 dadooing walls with ceramic tiles of size 20cm x 20cm x 6mm first quality design tiles of all colours laid in cement mortar 1:2 mix, 10mm thick and pointing with white cement using 0.40 kg / 1m2 including finishing the joint and pointing flush with tile surface etc., complete 28 paving the floor with best approved quality fine polished tandon shagbad green stone slab of size below 2 x 220mm thick laid over a cement mortar 1:3 mix, fixing the slab in true tight angles with minimum possible width of joints and polishing the joints with cement mortar 1:3 mix and polishing with floor polisher to a high degree to finish and curing etc. complete as directed by depat. officers. 29 supplying and fixing of cudappa slab of 20 / 30 / 40 / 50mm thick for cup board including cost of materials and labour etc complete 30 painting two coats with approved cement paint over cement plastered surface ceiling and other new surface includingcleaningprepering thesurfaceandcuringetc., complete 31 painting two coats with ready mixed plastic emulsion paint of 1st class quality and of approved color over a priming coat including through scraping clean removal of dirt etc., complete and including necessary plaster of paris putty wherever required 32 painting two coats with best synthetic enamel paint of approved colour for new iron works the rate is inclusive of all materials, brushes and scaffolding charges etc., complete complying with standard specification ( paint should be got approved by the departmental engineer befor use on work. 33 painting two coats with best synthetic enamel paint of approved colour for old iron works the rate is inclusive of all materials, brushes and scaffolding charges etc., complete complying with standard specification ( paint should be got approved by the departmental engineer befor use on work. 34 supplying, fabrication and fixing of ornamental grill for garidar andincluding cost of convayance of all materials and all labour charge for cutting, fabricating, walding etc, complete ( including one coat of primer ) and fixing in proper position with concrete packing by the direction of departmental engineers instruction etc, complete and as per standard specification. 35 supplying and laying rubberised interlocking paver blockm40 grade providing and laying of63mmthick high strength type conforming is 15658 2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40n / mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, stone dust cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification, . 36 wiring with 2 x 1.5 sq.mm ( 22 / 0.3 ) pvc insulated sc.unsheathed cu.conductor of 1100v grade in suitable pvc rigid pipe on wall and celiling with pvc accessories and with tw switch box and5 a.ft switch withinflush with wall, covered with hylum sheet of 3mm with painting of suitable colourfor open pvc light point. ( sd.no.21 ) 37 wiring with 2 x 1.5 sq.mm ( 22 / 0.3 ) pvc insulated sc.unsheathed cu.conductor of 1100v grade in suitable pvc rigid pipe on wall and celiling with pvc accessories and with tw switch box and 5 a.ft switch withinflush with wall, covered with hylum sheet of 3mm with painting of suitable colour for open pvc fan point. ( sd.no.21 ) 38 supply and fixing of 5a 3 pin and 2 pin combined flush type wall socket with 5a flush type switch on suitable t.w. box sd ( 10 ) 39 wiring with 2 x 1.5sq.mm ( 22 / 0.3 ) pvc insulated unsheathed sc.cu.conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150mm x 100mm x 113mm tw switch box with 3mm thick hylem sheet for 15a 3 pin non inter locking cs plug with painting ofsuitable colour with continous earth wire connection of 14 swg tc wire for open pvcpower plug pointetc, complete. ( sd.no.39 ) 40 supply and fixing of 1200mm 48’ ac ceiling fan complete with regulator with 300mm draw down rod on the existing clamp etc., ( sd.no.106 ) 41 supply and fixing of 4 18w crystal glass led tube light fitting complete with t.w. round blocks on wall or ceiling with flu tube with pvc unsheathed leads from terminal to the fitting. 42 supply and fixing ofwater closetnew glassed earthen ware t if 23” oriya type of approved quality with ”p” or “s” trap with sand cushion flooring and all round the closet using 40mm broken brick jelly in cement concrete 1:2:5 of 4” thick and plastering withcm1:3 20mm thick using river sand including fixing the water closet in position and giving necessaryconnection to ci stakes etc., complete 43 iwc 44 ewc ( 12.5 lit capacity ) 45 supply and fixing ofthe following pipes and specials etc., complete. 46 110mm dia pvc pipe 47 110mm dia pvc bend 48 110mm dia pvc clamp...

Rural Development And Panchayats Department - Tamil Nadu

40645371 tender for infra structure 2 works under nnt ( bp ) 2023 24 oddanchatram block tn 05 01.; 1. construction ofcommunity hall buillding at bodykudndur h / o kethaiyurumbu.estimate amount rs.20.00 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 5 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 6 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 below gl 9 above gl 10 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 11 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 13 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 14 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 15 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 16 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 17 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20 mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed 18 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 19 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 20 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 21 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 22 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall. 23 doorof size 1.80x 2.10m 24 doorof size 1.50x 2.10m 25 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall. 26 steel windowof size 1.50m x 1.20m 27 towards supply and delivery of new steel ventilatoras per std. specification 28 n type steel glazed ventilator of size 1.20 x 0.60m 29 labour charges for fixing of doors , windows and ventilator including all etc., complete 30 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 31 provision for water supply arrangements etc., 32 supply and fixing of 1000 litre hdpe tank 33 63mm pvc pipe 4kg / sqm 34 63mm pvc coupler 35 63mm pvc bend 36 63mm pvc mta 37 solvent cement 38 20mm dia pvc pipe 39 20mm dia pvc coupler 40 20mm dia pvc elbow 41 20mm dia pvc tee 42 20mm dia pvc fta 43 20mm dia gi waste not tap 44 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 45 provision for electrification 46 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 47 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 48 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 49 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 50 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 51 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 52 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 53 eb deposit amount 54 provisions for ramp with hand rail arrangements 55 provision for name board 56 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 57 2. construction ofcommunity hall buillding at athappanpatty h / o kuthiluppaiestimate amount rs.50.00 lakhs 58 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 59 supplying and filling in foundation, basement, etc with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 60 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 61 supplying and filling inbasement with u.s.gravel in layers of not more than 15cm thick well rammed, watered and compacted including cost & conveyance of sand and all labour charges etc., complete as per std. specifications. 62 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 63 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 64 below ground level 65 above ground level 66 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 67 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc.and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 68 cement concrete 1:8:16 ( one cement, eight sand and sixteen broken stone jelly ) using 20mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. 69 special ceiling plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 70 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 71 plastering with cement mortar 1:3 mix to 20mm thick including cost and conveyance of all materials & all labour charges etc., complete. 72 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated 73 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 74 paving floor with scratch proof ceramic tiles of any colour ofsize 305 x 305 x 6mm, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 75 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 76 paving floor with vertified tiles of size 600x600x8mm of any colour, laid in c.m 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 77 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 78 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 79 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 80 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 81 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 82 painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete. 83 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for community hall building. 84 ( d ) steeldoor of size 1.80 x 2.10m ( double leaf ) 85 ( d1 ) steel door of size 0.90 x 2.10m 86 ( d2 ) steel door of size 1.20 x 2.10m 87 ( d3 ) pvc door of size 0.75 x 2.10m 88 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for community hall building 89 ( w ) steel window of size 1.50m x 1.20m 90 ( w1 ) steel window of size 1.20m x 1.20m 91 ( v ) steel glazed ventilator of size 0.90 x 0.45m 92 labour charges for fixing of doors , windows and rcc jally in position including all labour charges etc., complete 93 steel doors with alongwith frame 94 steel windows and ventilator with alongwith frame 95 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 96 provision for electrification 97 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 98 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 99 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 100 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 101 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 102 supply and fixing of cfl bulb 11w including cost and conveyance of all materials and labour charges etc complete. sd 80 103 supply and fixing of 32 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 104 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 105 eb deposit amount 106 provision for water supply arrangements etc., 107 supply and fixing of 1000 litre hdpe tank 108 63mm pvc pipe 4kg / sqm 109 63mm pvc coupler 110 63mm pvc bend 111 63mm pvc mta 112 solvent cement 113 20mm dia pvc pipe 114 20mm dia pvc coupler 115 20mm dia pvc elbow 116 20mm dia pvc tee 117 20mm dia pvc fta 118 20mm dia gi waste not tap 119 earthwork excavation hard stiff clay and hard rock earth and pipe laying jointing and refilling the trench with excavation soils including all charges etc., complete 120 supplying and fixing of 110mm dia pvc pipein position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 121 provision for sanitary pipe line & dispersion arrangements 122 supplying and fixing pvc ventilating shaft of 110mm dia ( having working pressure 4 kg. / sq.cm ) with 3 metre height including cost of pvc cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers 123 supplying and fixing in position ci manhole covers with ci frames ( heavy duty ) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications 124 110mm dia pvc pipe 4kg / sqm 125 110mm dia pvc elbow 4kg / sqm 126 110mm dia pvc tee 127 towards the cost of providing staircase / ramp hand rail arrangements with ms pipe and flats including one coat of priming etc., complete 128 provision forname board with work detailsincluding cost and conveyance and all labour charges etc., complete 129 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Council Of Scientific And Industrial Research - Tamil Nadu

40577960 tender for minor works in gas separation lab at csir cecri, karaikudi; 1 providing and fixing factory made single extruded wpc ( wood polymer composite ) solid door / window / clerestory windows & desertory other frames / chowkhat comprising of virgin pvc polymer of k value 58 60 ( suspension grade ) , calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg / cum, screw withdrawal strength of 2200 n ( face ) & 1100 n ( edge ) , minimum compressive strength of 58 n / mm2, modulus of elasticity 900 n / mm2 and resistance to spread offlame of class acategorywith property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position with m.s hold fast / lugs / ss dash fasteners of required dia and lengthcomplete as per direction of engineer in charge. ( m.s hold fast / lugs or ss dash fasteners shall be paid for separately ) . note: for wpc solid door / window frames, minus 5mm tolerance indimensions i.edepth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2 frame size 45 x 70 mm 3 providing and fixing factory made single extruded wpc ( wood polymer composite ) solid board one side white color and other side of board laminted with pvcfoil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom / kitchen cabinet etc. of required sizes comprisingof virgin polymer of k value 58 60 ( suspension grade ) , calcium carbonate andnatural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum density of 650 kg / cum and screw withdrawal strength of 1800 n ( face ) & 900 n ( edge ) , minimumcompressive strength50 n / mm2, modulus of elasticity 850 n / mm2 and resistance to spread offlame of class acategory with property of being termite / borer proof, water / moisture proof and fire retardant and fixing with stainless steel piano hinges / soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer in charge. ( note: stainless steel piano hinges / soft close clip on concealed hinges and necessary s.s screws shall be paid separately ) 4 25 mm thick 5 providing and fixing stainless steel soft closing spring hinges at 0 degree hinges ( hydraulic type ) of approved make / brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of engineer in charge. 6 providing and fixing stainless steel fancy handle of approved make fixed with ss screws etc. complete as per direction of engineer in charge. 7 200 mm 8 providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 9 double strip ( horizontal type ) 10 providing and fixing bright / matt finished stainless steel tower bolt of approved quality & make with necessary screws etc all complete. 100x10mm 11 laying old cement cocrete interlocking paver blocks of any design / shape laid in required line, level, curvature, colour and pattern overand including 50 mm thick compacted bed of coarse sand, filling thejoints with fine sand etc. all complete as per the direction of engineer in charge. ( old cc paver blocks shall be supplied by the department free of cost ) 12 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 13 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete. 14 fixed to steel windows by welding 15 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 16 two or more coats on new work...

Council Of Scientific And Industrial Research - Tamil Nadu

40538235 tender for various minor repair works in institute area at csir cecri, karaikudi; 1 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 2 applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 3 water thinnable cement primer 4 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 5 two or more coats on new work 6 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 7 two or more coats on new work 8 providing and laying a single layer of tarfelt sheet weighing not less than 1kg / sqm of approved quality / approved by the engineer in charge over one coat of bituminous emulsion paint and pressed wellwith existing ac sheet roofing including ridges as directed ( one coat of bituminous emulsion paint to be paid separetly ) . 9 taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the engineer in charge. 10 providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to is: 1868 with minimum anodic coating of grade ac 15 ) of approved design / pattern, with approved standard section and fixed to the existing window frame with c.p. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of engineer in charge. ( only weight of grill to be measured for payment ) . 11 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fastenersto be paid for separately ) : 12 for fixed portion 13 powder coated aluminium ( minimum thickness of powder coating 50 micron ) 14 for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) 15 powder coated aluminium ( minimum thickness of powder coating 50 micron ) 16 providing and fixing 9 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer in charge. pre laminated particle board with non decorative lamination on both sides 17 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) : 18 with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) 19 providing and fixing bright / matt finished stainless steel handles of approved quality & make with necessary screws etc all complete. 150mm 20 providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. 21 providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. 22 twin rubber stopper 23 providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 24 providing & applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg / 10 sqm. one coat of self priming of cementatious waterproofing polymer ( dilution with water in the ratio of 1:1 ) and two coats of cementatious waterproofing polymer ( dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of engineer in charge. 25 providing & fixing sun control film in the glass paneled steel windows, inclusive of surface cleaning, pasting etc., and fix the film as per the instructionof the site –engineer in charge. 26 finishing walls with acrylic smooth exterior paint of required shade : 27 new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) 28 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 29 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 30 supplying chemical emulsion in sealed containers including delivery as specified. 31 chlorpyriphos emulsifiable concentrate of 20% 32 diluting and injecting chemical emulsion for post constructional anti termite treatment ( excluding the cost of chemical emulsion ) : 33 treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 ce ment : 2 coarse sand ) to the full depth of the hole : 34 with chlorpyriphos e.c. 20% with 1% concentration 35 removing and re fixing of existing steel glazed door / windows after necessary alternation including necessary repair work of proper locking arrangements ( using ms flats, etc. ) and hinges as per site requirement as directed by the engineer in charge. ( upto 4.00 sqm of shutters ) 36 excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 37 all kinds of soil 38 pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 39 cleaning the man holes / septic tanks including removal of blockages in the existing lines by mechanical means including transportation charges as directed by the engineer in charge ( 6000litre capacity ) 40 making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand ) , finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 41 for pipes 100 to 250 mm diameter 42 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 43 hot finished welded type tubes 44 providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 45 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 46 in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 47 providing and fixing expansion hold fasteners on c.c. / r.c.c. / brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. 48 wedge expansion type 49 fastener with threaded dia 12 mm 50 repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of engineer in charge. 51 providing and fixingpvc swr pipes type b conforming to is:13592 including jointing with necessary fittings as directed by the engineer in charge. 150mm diameter 52 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with r.c.c. top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) , inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design : inside size 90x80 cm and 45 cm deep with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 53 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : 54 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources ) 55 1:4:8 ( 1 cement : 4 manufactured sand derived from recycled concrete aggregate ( rca ) : 8 graded stone aggregate 40 mm nominal size recycled aggregate ( ra ) 56 providing and fixing unplasticized polyvinyl chloride ( upvc ) pipes, including all upvc threaded fittings. this includes jointing of pipes & fittings with one step suitable solvent and testing of joints complete as per direction of engineer in charge. 80mm dia upvc pipe 57 providing and fixing upvc ball valve of approved quality, high or low pressure, with plastic floats complete as directed by the engineer in charge. 80 mm dia upvc ball valve 58 making connection of g.i. distribution branch with g.i. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 59 50 to 80 mm nominal bore 60 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 61 all kinds of soil. 62 half brick masonry with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundations and plinth in : 63 cement mortar 1:4 ( 1 cement : 4 coarse sand ) 64 12 mm cement plaster of mix : 65 1:6 ( 1 cement: 6 coarse sand ) 66 grouting the joints of stone masonry having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade ( 0.10 kg of hardener and 0.20 kg of resin per kg ) , including filling / grouting by suitable gun / pump at required pressure and finishing complete as per direction of engineer in charge. 67 ( a ) designing, fabricating, testing, installing and fixing in position curtain wall with aluminium composite panel cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. ( b ) providing, fabricating and supplying and fixing panels of aluminium ( c ) composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick fr grade mineral core sandwiched between two aluminium sheets ( each 0.5mm thick ) . the aluminium composite panel cladding sheet shall be coil coated, with kynar 500 based pvdf / lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer ( service ) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. the fastening brackets of aluminium alloy 6005 t5 / ms with hot dip galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, ss 316 pins and anchor bolts of approved make in ss 316, nylon separators to prevent bi metallic contacts all complete required to perform as per specification and drawing the item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. base frame work for acp cladding is payable under the relevant aluminium item.s the contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the engineer in charge. however, for the purpose of payment, only the actual area on the external face of the curtain wall with aluminum composite panel cladding ( including width of groove ) shall be measured in sqm. up to two decimal places. 68 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete. 69 fixed to steel windows by welding 70 providing and fixing square mouth s.w. gully trap class sp 1 complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 71 150 x 100 mm size p type 72 with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 73 providing and fixing 63 mm dia pvc pipes ( 4kg / cm2 ) ( finolax or equivalent ) complete with necessary fittings and clamps including cutting and making goodthe walls etc. 74 providing and fixing double scaffolding system ( cup lock type ) on the exterior side, up to seven story height made with 40 mm dia m.s. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with m.s. tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .the scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in charge .the elevational area of the scaffolding shall be measured for payment purpose .the payment will be made once irrespective of duration of scaffolding. note: this item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. 75 supplying and fixing self adhesive decorative film for glass doors / winows / glass partition / backing of suitable boards including requireddesign as directed by the engineer in chage....

Rural Development And Panchayats Department - Tamil Nadu

40468894 tender for vellore district pmagy 2023 24 3 works in pakkam panchayat at gudiyatham block package no 08 1 vellore district pmagy 2023 24 3 works in pakkam panchayat at gudiyatham block package no 08 2 providing of new pipe line at lakshmi nagar in pakkam panchayat of gudiyatham block. 3 cost of 63 mm pvc pipe 4 ksc 4 cost of 63 mm pvc bend 5 earthwork excavation and depositing on bank with initial lead and lift in all soilhard stiff clay, stiff black cotton, hard red earth, shales murram gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil ss20b ( sor 2022 2023 pg. no. 291 schedule no. 1 ( b ) ) 6 laying and jointing the pvc pipes & specials into trench sor 2022 2023 pg. no. 266 schedule no. 11b ( i ) ) 7 refilling trench with excavated earth after laying the pipe 8 letering and painting name board 9 name of work: construction of drainage atp. venkatapuram colony in pakkam pachayatof gudiyatham block. 10 earth work excavation in all clauses of soil such as hard stiff clay, hard gravelly soil as per ss 20 b for narrow foundation. 11 cement concrete 1:4:8 mix using 40mm hbg metal including cost and conveyance of all materials to site including all labour charges for filling etc complete. 12 supplying & erecting centering for sides & soffiots to concrete works including cost and conveyance of all materials to worksite and all labour charges etc., complete 13 cement concrete 1:2:4 mix using 20mm hbg metal including cost and conveyance of all materials to work site and all labour charges etc.complete 14 plastering with cement mortar 1:5, 20mm thick including cost and conveyance and all labour charges etc. 15 letering and painting name board 16 name of work : construction of new anganwadi building at p. venkatapuram colony in pakkam panchayat of gudiyatham block. 17 earthwork excavation and depositing on bank with initial lead and lift in all clauses of soil including cost of labour etc complete ss20b 18 collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for fillingetc.complete, 19 p.c.c 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all etc.. complete 20 supplying and erecting centering for all pcc items including cost and conveyance of all etc.. complete 21 supplying and erecting centering for all pcc items including cost and conveyance of all etc.. complete 22 supply and fabrication of mild steel including cost and conveyance of all etc.. complete 23 rcc 1:1.5:3 mix using 20mm including cost and conveyance of all etc.. complete 24 brickwork in cm 1:5, using country bricks including cost and conveyance of all etc.. complete 25 plastering in cm 1:4, 20mm thick including cost and conveyance of all etc.. complete 26 plastering in cm 1:3, 10mm thick including cost and conveyance of all etc.. complete 27 plastering in cm 1:5, 12mm thick including cost and conveyance of all etc.. complete 28 supplying & fixing of steel door ( 0.900 x 2.10m ) etc., complete 29 supplying & fixing of steel door ( 0.75x 2.10m ) etc., complete 30 labour charges for fixing the steel door 31 supplying of steel windows ( 1.20 x 1.30 ) etc., complete 32 labour charges for fixing steel windows in position and all 33 supply and cost of steel vendilator including the conveyence charges and all etc complete 34 weathering course with brick jelly lime concrete using 20mm brick jelly including cost and conveyance of all etc.. complete 35 finishing the top of roof withpressed tiles including cost and conveyance of all etc.. complete 36 dadooing with printed design colour glazed tiles of size 300 x 450 x 8mm laid incm 1:3, 10mm thick & pointing with white cement using 0.4kg / cm2for etc complete 37 vetrified tiles of best quality and free from any defect, approved quality colour set in cm 1:2 including all cost and convenyance for etc complete 38 painting two coats with readymixed oil bound distemper etc., complete ( for internal ) including cost and conveyance of all etc.. complete 39 paintingtwo coats with approved colour emulsion paint ( for external ) including cost and conveyance of all etc.. complete 40 painting two coats over new irons with good quality of enamel paint including cost and conveyance of all etc.. complete 41 supplying and fixing in position best indian make white glazed earthen ware oriya type indian water closetincluding cost and conveyance of all etc.. complete 42 flooring with cuddapah slabs 50mm thick over a bed of concrete 100mm thick and pointed with cement mortar 1:3 10 sqm including cost and conveyance of all site etc. complete. 43 provision for 500 ltr hdpe tank 44 provision for gm gate valve 32mm dia 45 cost of32mm diapvc pipe 10 ksc 46 cost of 20mm dia pvc pipe 10 ksc 47 provision for pvc screw down tap heavy type 20mm dia 48 20mm pvc bend 49 20mm pvc tee 50 110mm pvc pipe 6 ksc 51 110mm pvc pipe tee 52 110mm pvc pipe bend 53 provision rain water harvesting structure 54 provision for baby pan with fittingand specials and labour charges etc. copmlete 55 provision for cartoon drawings 56 wiring 2 x 1.5 sq.mm ( 22 / 0.30 ) pvc insulated unsheathed sc.cu.conductor of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with in flush with wall covered with hylem sheet of 3 mm thick with painting of suitable colour for concealedpvc light / fan point ( sd no.25 ) 57 supply and fixing of4 18wled tube with fitting inclusive of all charges 58 wiring 2 x 1.5 sq.mm ( 22 / 0.30 ) pvc insulated unsheathedsc.cu. conductor of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with in flush with wall covered with hylem sheet of 3 mm thick with painting of suitable colour for concealedpvc plug point ( sd no.38 ) 5 pin plug point 59 supply and fixing of 1200mm sweep ac ceiling fan complete with stepped electronic regulator with 300mm down rod on the existing clamp sd 106 60 supply and fixing of water tight bulk head fitting with guard ( philips / bajaj / crompton / klite ) suitable for incandencent lamp and 60w bulb ( sd n0.83 ) 61 supply and run of 2 of 1.50 sq.mm polythene insulated pvc sheathed heavy duty sc copper conductor of 1100 v grade on 7 / 20 gi bearer wire for service connection mains ( sd no.64 ) 62 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1 x 1 / 8 copper flat ) on tw plank of size 375mm x 300mm x 19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit. ( sd no. 125 ) 63 supply and run of 2x4 sqmm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100v grade in 25mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 70 64 supply and fixing of 16 amps dp switch of500v with metal clad with fuse and neutral sd 142 65 sd 139 66 sd 134 67 sd 234 68 provision for cuddapah sink 69 letering and painting name board 70 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40462831 tender for repairs to pue school buildings & toilet , mugaiyur block at villupuram district.; 1 repairs to pue school rcc roof building east facing in paranur panchayat 2 chipping the concrete & roughning the surface 3 granulothick floor finish including cost & conveyance and labour charges et complete. 4 dismantling the existing damaged pressed tiles without weathering coarse including cost & conveyance and labour charges et complete. 5 terrace finshing with one course of pressed tiles of size 23x23x2cm 40% new and 60%with cement mortar 1:3 mix and pointed with the same oiled mortar including cost & conveyance and labour charges et complete. 6 plastering with cement mortar 1:3 mixto 10 mm thick including cost and conveyance of all materials to site and all labour 7 white washing two coats using shell lime including cost and conveyance of all materials to site and all other labor charges for etc com, . 8 outer wall painting two coats with approved quality emulsion paint including cost & conveyance and all labour charges etc complete. 9 distempering two coats with oil bound distemper over cement plastered surface including cost & conveyance and all labour charges etc complete. 10 painting two coats with approved quality of paint over old iron works including cost & conveyance and all labour charges etc complete. 11 black board painting two coats with approved quality of exising black board including cost & conveyance and all labour charges etc complete. 12 cub board with looking door 13 repairs to steel doors etc complete 14 repairs to steel window etc complete 15 special design art work with first class quality emulsinpaint including wall putty, priming coat etc, complete. rate for 100 sq.feet 16 name board charges 17 provision for photographic charges 18 repairs to pue school rcc roof building south facing in v.sithamur panchayat 19 chipping the concrete & roughning the surface 20 granulothick floor finish including cost & conveyance and labour charges et complete. 21 dismantling the existing damaged pressed tiles without weathering coarse including cost & conveyance and labour charges et complete. 22 terrace finshing with one course of pressed tiles of size 23x23x2cm 40% new and 60%with cement mortar 1:3 mix and pointed with the same oiled mortar including cost & conveyance and labour charges et complete. 23 plastering with cement mortar 1:3 mixto 10 mm thick including cost and conveyance of all materials to site and all labour 24 white washing two coats using shell lime including cost and conveyance of all materials to site and all other labor charges for etc com, . 25 outer wall painting two coats with approved quality emulsion paint including cost & conveyance and all labour charges etc complete. 26 distempering two coats with oil bound distemper over cement plastered surface including cost & conveyance and all labour charges etc complete. 27 painting two coats with approved quality of paint over old iron works including cost & conveyance and all labour charges etc complete. 28 black board painting two coats with approved quality of exising black board including cost & conveyance and all labour charges etc complete. 29 cub board with looking door 30 repairs to steel doors etc complete 31 repairs to steel window etc complete 32 special design art work with first class quality emulsinpaint including wall putty, priming coat etc, complete. rate for 100 sq.feet 33 name board charges 34 provision for photographic charges 35 repairs pues toilet at gudalur panchayat 36 chipping the concrete & roughning the surface 37 paving the floor with best quality anti skidtiles of any approved colour and size 300 mm x 300 mmx 8 mm shape and quality laid in cementmortor 1 : 2 to 20 mm thick in all floors and the top pointed with the white cement 0.40 kg mixed with the same colouring pigments etc complete 38 white washing two coats using shell lime including cost and conveyance of all materials to site and all other labor charges for etc com, . 39 outer wall painting two coats with approved quality emulsion paint including cost & conveyance and all labour charges etc complete. 40 distempering two coats with oil bound distemper over cement plastered surface including cost & conveyance and all labour charges etc complete. 41 painting two coats with approved quality of paint over old iron works including cost & conveyance and all labour charges etc complete. 42 water supply arrangements charges 43 name board charges 44 provision for photographic charges 45 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Military Engineer Services - Tamil Nadu

40426653 tender for special repairs to certain bldgs and communityhall ( p 75 ) at afac coimbatore; 1 removal of plants / shrubs grown on walls / slabs / beams by making holes or demolition of concrete etc and including applying suitable chemical for killing the roots of plants, filling of holes with concreteand making good complete all as specified and directed. 2 chipping / removing loose concrete in cloumns / beams / chajjas / roof slab etc. up to reinforcement bars without damaging the reinforcement, removing all the loose material and to make all the exposedsurface free from dust and all impurities etc complete allspecified and directed. 3 removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution reebaklens rr of fosroc / sika rust off 100 / equivalent in bostic india ltd by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush and applying anti corrosive coating to reinforcement nitozinc primer of fosroc / sika friazinc r / equivalent in bostic india ltd , all as recommended by product manufacturer. 4 providing and applying one coat of structural grade epoxy coat by brush of approved make . mixing of two components will be as directed by manufacturer .application shall be provided not more than 5 hours before application of micro concrete / polymer mortar etc complete all as specified by the manufacturer.make: nitobond ep of fosrock / sikdur 32lp / equivalent in bostic india ltd 5 providing and applying n exc 40 mm thick ( in layers of each 10mm thick ) shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar renderoc sp 40 of fosroc / sika plastocrete plus / equivalent in bostic india ltd, mixed with water in a water & powder ratio 0.18 in ceiling of roof slab / chajjas / beams / parapet walls etc.note: quoted tate is deemed to be inclusive of provideing scaffolding for working in patches upto a height of 15 mtr complete all as specified and directed. 6 surface grinding, rounding off all edges to minimum of 25mm radius andand applying nitowrap cws 230 of fosrock ( or ) sika wrap 230c, uni directional, high strength, light weight, non corrosive carbon fiber sheets of all around the periphery of pier for entitre height of pier.the frp fabric used shall be ofzero degree unidirectional fibers havingfiber density of 1.8 g / cc and shall have tensile strength > 4900 mpa ; tensile modulous > 230 gpa and ultimate elongation of 2.1%. the substrate shall be primed with nitowrap 30 epoxy primer &nitowrap 410 impregnating resin saturant shall be used for saturating the fibers.saturant used shall have tensile strength of >30 mpa; elongation > 2% ; flexural strength > 30 mpa ; tensile modulous > 2400 mpa & flexural modulous > 1700 mpa when tested as per astm d638 type i and astm d 790 & glass transition temperature > 50 deg celcius as per astm e 1356. the adhesion of the entire system ( frp sheet, saturant and primer combined ) with concrete shall be > 3.5 mpa with concrete failure as per astm d 4541.wrapping the cfrp fabric to rcc member atdesired orientation using tamping rollers to avoid any airvoids etc. and sprinkling sand over it as per direction and satisfaction of engineer in charge, etc, complete. product used shall have ce ( ce 29842 ) marking and compliance according to construction products directive 89 / 106 / eec ( cpd ) 7 demolition of rcc roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work . 8 m&l for flat form work for rough finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup ports, overhangs, etc. also splays between floors and beams, etc. 9 m&l for flat form work for rough finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) . 10 m&l for rcc m 25 in beams, cantilevers, bressummers, lintels over 1.5m span 11 m&l for rcc m 25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like 12 s&f mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips 13 all as above item but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders 14 taking down existing roof treatment includingscreed bed , app membrane etc upto mother slab of roof and cleaning with wire brushe and water complete , including shifting of mulba from roof to ground floor for futher disposal all as specified and directed by e i c. 15 m&l for pcc 1:1.5:3 type b0 admixed with nitobond sbr of fosrock ( or ) equivalent products in sika / asain paints @ 2% by weight of cement in roof slabs for filling up spots of loose screed / concrete , complete all as specified and directed by e i c. 16 supply and application of single component, seamless, spray applied, hybrid elastomeric pu based material i.e nitoproof 725 of fosroc chemicals ( or ) sikalastic 590 of sika india pvt ltd ( or ) equivalent in any approved make as approved by ge over a coat of primer i.e nitoproof wb primer of fosroc chemicals ( or ) diluted sikalastic 590 of sika india pvt ltd ( or ) equivalent in any approved make as approved by ge, all as recommended by manufacturer ans as specified.note: ( i ) average minimum dftof pu based material shall be 1mm and shall be applied by using a graco pump. ( ii ) pu based material shall process the following properties solids by volume 65%, tensile strength astm d412 1.75mpa, density 1.3 g / ml, elongation astm d 412 350%, adhesion to substrate concrete 1.9mpa, resistance to water 10m pressure. ( iii ) rate are deemed to be include for cleaning and preparation of surface to receive pu water proofing system including filling of cracks with cementitious repair mortars i.e renderoc cs of fosrock chemicals ( or ) equivalent of approved make. ( iii ) work shall be got carried out by authorised applicator of the manufacturer and it shall be got approved by the ge before progressing the work. ( iv ) 10 years of guarantee shall be provided and security amount shall be deposited as speicified in tender documents. 17 taking down cement plaster on brick or stone walls, ceilings, etc including racking out joints, hacking for key, scrubbing down with water, etc 18 m & lrendering in cm 1:3, 5mm thick on fair faces of brick work or concrete surfaces on ceiling complete all as specified. 19 m & l for preparation of newlyplastered surfaces and applying threecoats of white washon ceiling.surface all as specified. 20 m&l for rendering with wpc in cm 1:4, 15mm thick on othe thanfair faces of brick work or concrete surfaces all as specified and directed. note : wpc shall be measured and paid separately 21 m&l for rendering in cm 1:6, 10mm thick on fair faces of brick work or concrete surfaces all as specified and directed. 22 m & l preparation newly plasteredof wall surfaces and applyingtwo coats of cement base paint over a coat of primerall as specified and as directed directed by engr in charge. 23 m & l prepation of newly plastered wall surfaces and applyingtwo coats of distemper oil emulsion over over a coat of primerall as specified and as directed directed by engr in charge. 24 supply only intergral waterproofing compound 25 preparation of old treatedof wall surfaces and applyingone coat of cement base paintall as specified and as directed directed by engr in charge.note: ( i ) this item of work shall be executed upto a height of 30 mtr height buildings / structures / rcc ohts. ( ii ) scaffolding required to be done for executing the work above the normal heights as specified in ssr pt ii shall be measured and paid separately under a separate item for the whole building / structure. 26 m & l for applyingone coats of distemper oil emulsion on old treated / decorated surfaces of wall including preparation of wall all as specified and as directed directed by engr in charge. 27 m & l for preparation of oldplastered surfaces and applying twocoats of white washon ceiling.surface all as specified. 28 m & l for preparation of oldtreated wall surfaces and applying twocoats of white washall as specified. 29 preparing old surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint. 30 preparing old surface of steel and steel based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint. 31 providing & fixing double steel scaffolding system ( cup lock type ) on the exterior side of the building / structure, including additional rows of scaffolding in stepped manner as per requirement at site, made with 40mm dia ms tube, placed 1.5mtr c / c ( maximum ) , horizantal & vertical ms tubes jointed with cup & lock system in the scaffolding for working platform etc amd maintaining it in a serviceable condition for execution of work and removing it thereafter. the scaffolding system shall be stiffned with bracings, runners, connecting with building etc wherever required to ensure safety of workmen all as directed by engr in charge.note: 1.area derived by multiplying the outer most external perimeter and height of the building / structure shall be measured for payment.2. the payment shall be made only once after completion of all external items of work w.r.t the building / structure. 3. after completion of the work the material of the scaffolding shall be the property of the contractor and required to be removed from the site. 32 demolition of concrete in above ground floors and pavings exc 15 cm thick 33 dismantling floor, hearth or wall tiling including cement mortor bedding ( but not backing to stone and rubbish off the premises complete all as specified and directed. 34 m & l for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by engr in charge.. 35 m & l for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by engr in charge.. 36 m & l glazed coloured ceramic tilesin vertical surface 350x250x7mm / 450x350x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by engr in charge.. 37 m&lfor screed bed or bedding layer of mortor 15 mmthick in cm 1:6 for laying floor finishes all as specified and directed. 38 m&l for rendering 10mm thick on fair faces of brick work or concrete surfaces with cm 1:4as in backing coat of skirting / dado all as specified and directed. 39 m&l for brick work with sub class b bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 complete all as specified and directed. 40 demolition of brickwork or stone / boulder masonry, built incement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles 41 taking down chowkhats or frames with shutter ( with out taking off the shutters from the frames ) size not exc 1.50 sqm each and all as specified and directed. 42 taking down shutters of any descriptionexc 1 sqm and n exc 2sqm each all as specified and directed. 43 s&f iind class hard wood , 35mm thickplain, framed, panelled shutters ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers all as specified and directed. 44 s&f iind class hard wood, 35 mm thick glazed and skeletonshutter, open rebated and prepared to receive glass , gauge, etc without sash bars but divided into squares, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in ssr part i section 8, clause 8.24 ( a ) and fitted to chowkatscomplete all as specified and as directed by engineer in charge. 45 s & f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified and as directed by engineer in charge. 46 s & f factory made solid pvc moulded door shutter with wood eps, 30mm thick , with 2, 4, or 6 raised panel design with 2mm thick mouldedprelaminated pvc sheet on both facessupplying & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by engineer in charge. 47 steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded . 48 ditto, but without glazing bars 49 s&f mild steel work in hold fasts etc and similar work conforming to fe 290 gde e 165. 50 preparing surfaces of wood and wood based materials, steel and iron work , new or old , treating small articles such as stop, covers gully gratings, hold fasts ends of posts, back of chowkats etc , area n exc 0.1 sqm each and treated with tar or coal tar black paint. 51 m&l for cement concrete type b1 1:2:4 ( 20mm graded aggregate ) for fixing of hold fast, including finished to match with exiting surfacesall as specified and directed. 52 s&f iind class hard wood, small fittings such as shaped door and window stops and like articles n exc 200 cu cm each all as specified and directed. 53 s&f300mm long aluminium alloy, anodised sliding door bolt with hasp, staple ( bolt type ) and fixing bolts and sliding bolts of extruded sections or cast aluminum alloycomplete and all asspecified and directed 54 s & f floor door stopper 140mmlong with cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring. fixed in floor 55 s&f100mm long butt hinges, medium weight, coldrolled mild steel and all asspecified and directed 56 s&f 150mmaluminium alloy , anodised, sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy all as specified and as directed. 57 s&f 150mm longaluminium anodised barrel towers bolts of extruded section and all asspecified and directed 58 s&f 150mm extruded aluminium alloy handles, fabricated type anodised asspecified and directed 59 m&l for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces all as specified and directed. 60 framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 61 m&l for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces all as specified and directed. 62 supply only3 mm figured glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 63 supply only stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples. 64 s&f in repair only4mm sheet glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 65 s&f in repair3 mm figured glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 66 s&f in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples. 67 taking up or down steel tubing and connections, and removing to store for taking in account of credit for 15mm bore complete all as specified and directed. 68 all as per itemabovebut for 20 mm bore 69 3 layer pp r ( polypropylene random copolymer ) concealed pipes / un concealed pipes sdr 7.4 ( pn 16 ) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all pp r plain and brass threaded poly propylene random fittings fixed complete to walls / ceilings or laid on floors of 16mm outer dia of pipe all as specified and as directed 70 all as per item no 69 above but 20mm dia 71 taking down & refixing ppr 15mm / 16mm pipes 72 taking down & refixing ppr 20mm 73 s&f in repairs vitreous china wash down water closet pan ( pedestal pattern ) , white including seat cover and flush pipe etc complete all as per specified and as directed by engineer in charge. 74 s & f in repairs pvc valveless, syphonic action type, flushing cistern of 10 ltrs capacity , low level , white, with inlet , ball valve, float and handle including brackets and flush pipe etc complete all as specified and as direted by engineer in charge. 75 s& f in repair vitreous china wash basin, white, flat back, size 450x300mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including 32mm ptmt waste cupling , complete all as specifed and directed. 76 s&f in repairs bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. 77 s&f in repairs two way bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. 78 s&f in repairs pillar taps fancy type cast copper alloy, with capstain head, chromium plated screwed down high pressure, with long shanks and fly nuts screwed for iron pipe and fixed 15 mm bore. 79 s & f pvc connections 15 mm size with ptmt nuts of length 450 mm 80 s&f in repairs chromium plated angle valves, cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size. 81 s&f brass chromium plated health faucet with hand held and spring operated control valve with pvc flexible pipe connection of suitable length as directed fixed to 15 mm bore pipe. 82 m & l 75mm dia for pvc ( swr ) multi floor trap ofwith grating including jointing with solvent cement etc complete, 83 s & f in repairs 110mm dia pvc ( swr ) pipe single sockted in any length with rubber ring joints fixed to wallwith clamp complete all as specified and directed. 84 s&f 110mm radius pvc ( swr ) bendscomplete all as specified and directed. 85 s&f 110mm radius pvc ( swr ) branch piece, single ( single t ) equal or unequal complete all as specified and directed. 86 s & f in repairs75mm dia pvc ( swr ) pipe single sockted in any length with rubber ring joints fixed to wallwith clamp complete all as specified and directed. 87 s & f 50mm diaunplasticised pvc pipe of pressure rating 10 kgf / cm2 fixed complete to walls, ceiling or in floors etc complete 88 m & l for 125 / 110mm dia pvc ( swr ) gullytrap including setting jointing with solvent cement etc complete, 89 s&f 110 mm borepvc ( swr ) vent cowl 90 s&f 600mm x 450mm bevelled edge looking mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed towooden plugs with chromium plated brass screws and cup washers. 91 dismantling of pvc water tank 500 ltr capacity and removing to store 92 s&f moulded polyethylene 500 ltr water tank storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position complete all as specified and directed by engr in charge. 93 s&f in repairs 25 mm ball brass valves, high pressure, with polythene float and flynut cimplete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. 94 m&l for cement concrete type b1 1:4:8 ( 20mm graded aggregate ) in filling and mass concreteall as specified and directed. 95 m&l forsand cushioning under floor or in foundation including watering and consolidation for laying of interlocking pavour block. 96 machine pressed precast concrete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness, m 35 grade with grey cement and no pigments 97 removalof debris / building material out side the campus including loading and unloading, etc to a distance exc 5km but n exc 10 km out side the md land complete all as specified and directed. note: location and permission of depositing the building materials / debris disposal outside the md land shall rest with contractor at his own arrangement. 98 taking down chain link fencing including ms straining rods and ms flat iron strips all as directed by engr in charge 99 fixing only chain link fencing including line wires any mesh size and type of standerds rails scraining babs etc incl permission o binding wire ( note supply of chain link will be measured seperately ) . 100 supply only chain link ms galvanized fencing of any mesh size and type note fixing shall be measured under serial item no here in above. 101 m& l hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencingincluding cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets ( for securing wire mesh etc. ) including all necessary drilling, bolting or riveting, etc., and similar work conforming to fe 290 gde e 165 102 tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to fe 290 gde e 165 103 dismantling wrought iron or mild steel work of any description not otherwise provided for 104 demolition ofcement concretein below or above ground level and paving not exc 15 cm thickness 105 m&l 25 mm thick cement concrete type b 0, 1:2:4 ( 12.5 mm graded aggregate ) as in sub base of floors without extra cement all as specified. 106 s& f heavy duty virtified tiles 300x300mmx10mm in flooring all as specified and as directed. 107 s& f heavy duty virtified tiles 300x300mmx10mm in skirting / dado as specified and as directed. 108 m & l non skid coloured ceramic floor tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface. 109 m&lbrick work with fly ash bricks, straight or curved on plan exc 6 mtr mean radius built in cm 1:6 with old size bricks 110 m&lbrick work with fly ash bricks, straight or curved on plan exc 6 mtr mean radius in half brick thick walls built in cm 1:6 with old size bricks 111 m & lrendering in cm 1:6, 10mm thick on fair faces brick or concrete surfaces finished even and smooth without using extra cement 112 m & l prepation of newly plastered wall surfaces, apply 3mm thick wall care putty and applyingtwo coats of distemper oil emulsion over a coat of primerall as specified and as directed by engr in charge. 113 m&l for preparation of old surface and applying one coat of white wash on ceiling surface all as specified and directed . 114 s&f sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connection union to pipe, overall size 915x460mm bowl size 410mmx330mmx160mm complete all as specified and directed. 115 hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames of stone, concrete or brick surrounds, glazed with putty or fixed with beads. 116 s&f sheet glass, ordinary quality 4mm thick and glazing with oil putty or fixed with beads in square n.exc 0.5 sqm in each pane. 117 taking down shutters of any description n. exc 1.00 sqm each all as specified and directed. 118 taking down chokhats or frames with shutters ( without taking off the shutters from the frames ) size exc 1.50 sqm but n exc 4 sqm all as specified and directed. 119 s & f for second class hard wood with plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints 120 supply only4mm sheet glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 121 s & f butt hinges medium weight cold rolled mild steel, and fixed 75 mm size 122 s&f 100mm long extruded aluminium alloy handles, fabricated type, anodised and all asspecified and directed 123 s&f 200mm longaluminium anodised barrel towers bolts of extruded section and all asspecified and directed 124 removing buildingmaterialout side the campus including loading and unloading etc., to a distance exc 5.0 km but not exc 10.0km out side the md land ( ministry of defence ) where responsibility regarding place of deposition and obtaining permission from all authorities etc., in this regard will be of contractor responsibility and allas specified. 125 s & f pvc ( swr ) pipe 75mm diasingle sockted in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 126 s & f pvc ( swr ) pipe 110mm diasingle sockted in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 127 s&f 20mm bore gun metal , globe or gate valve, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed. 128 s&f soap dish ( poly carbonate ) complete all as per specified and as directed by engineer in charge. 129 s&f in repairs 125mm dia shower rose brass chromium plated with or without seivel joints, including fixing to steel pipe or union complete all as specified and directed. 130 s & f factory made solid panel pvc door shutter 30mm thick ( style ) consisting of frame made out of m.s tube for top & bottom rails. m.s frame shall be covered with heat moulded plain colour pvc c channel having pvc sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour pvc sheet for top rial, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour pvc sheet to be fitted in the m.s frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement , suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by engineer in charge. 131 m & l for cement concrete type c1, 1:3:6 ( 20mm graded stone aggregate ) 75 mm thick as in plinth protection including necessary form work as required. 132 m & l for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub structure to a depth of 300mmincluding excavating channel along the wall and rodding etc. complete all as specified and as directed by engr in charge. 133 dismantling of asbestos cement ( corrugated, semicorrugated, etc. ) sheets in roof coverings 134 s & f pre painted galvalume aluminium zink coating gi based corrugated steel sheet 0.50 mm thick of any color having tensile stregth of 550 mpa as in roof covering / cladding fixed to walls fixed with self tapping screws as specified. 135 m&l for pcc 1:2:4 type b0 in roof slabs ( average thickness 50mm ) using water proofing compound complete all as specified and directed by e i c. note : wpc shall be measured and paid separately 136 m & l precast cement concrete 1:2:4 type b1 using 20 mm graded stone aggregate as in cover slab of manhole, drain cover, chullah, water troughs water troughs, shelves etc similar work with plain faces and set in cm 1:4 complete all as specified and directed. 137 s & f rolled mild steel work in tubular trusses including special shaped washer etc.complete using erw or induction butt welded tubes conforming to is 1161 1979 grade st 240. 138 s & f roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc to fe 410 w ( gde e 250 ) quality a 139 dismantling ceiling boards any description any thickness including cover fillets all as specified and directed 140 s&f anodised aluminium snap grid frame work for false ceiling all as specified 141 s&f exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid ( frame work for ceiling shall be measured and paid separately ) . 142 s&f hangers 6 mm dia. g.i. ( upto 1200mm length ) adjusting level fixed to roof slabs by means of ceilling cleats made out of g.i. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 143 m & l for granite ( of any type ) tiles 20mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement withadmixture of pigment to match the shade of granite stone including 15mm thick screed bed or bedding layer of in cm 1:6all as specified and as directed. 144 m & l for 18 mm thick veneered decorative plywood, grade 1 ( with bwr resin ) with decorative face veneers on both faces; fixed with screws to timber frame work etc complete all as specified and as diirected. 145 s&f continous ( piano ) hinges 30mmwidth mild steel, bright finish or electrogalvanised complete all as specified and directed. 146 s&f 100 mm long hasp and staple, aluminium anodised, inclufing bolt to hinge plate and fixed with screw complete all as specified and directed. 147 m&l hardcore with broken stone or boulders of gauge not exc 63 mm deposited spread and leveled in layers not exc 15 cm thick watered and rammed to a true surface . 148 m&l for chequered cement concrete tiles 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigmentin floors including 20 mm thick screed bed or beding layer in cement mortar 1:6 complete all as specified and as directed by engineer in charge. 149 m&l pcc 75 mm thick , type d21:4:840 mm graded aggregate as in sub base 150 supply and fixing factory made upvc white colour three track three panels sliding window with fly proof ss wire mesh ( two nos glazed & one no. wire mesh panels ) upto 1.50m height made of ( big series ) frame 116x45mm & sash 46x62mm both having wall thickness of 2.3+ 0.2mm and single glazing bead / double glazing bead of appropriate dimension. ( area of window above 1.75 sqm ) comprising of upvc multi chamfered frame, with inbuilt roller track and sash extruded profiles duly reiforced with 1.60+0.2mm thick galvanised mild steel section made from roll forming process of required length ( shape and size according to upvc profile ) , appropriate dimension of upvc extruded glazing beads and upvc exruded interlocks, epdm gasket, wool pile, zinc alloy ( white powder coated ) touch locks with hook, zinc alloy body with single nylon rollers ( weight bearing capacity to be 40kg ) , gi fastners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. profile of frame & sash shall be mitred cut and fuson welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame , the gap between frameand adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality , complete all as specified and directed by engineer in charge. ( glass or wire mesh shall be paid separately ) 151 spply and fixing factory made upvc white colour fixed glazed window / ventilator made of ( small series ) frame 47x50mmmullion 47x68mm both having wall tickness of 1.9+ 0.2mm and single glazing bead of appropriate dimension. ( area upto 0.75 sqm ) comprising of upvc multi chamfered frame, and mullion ( where ever required ) extruded profiles duly reiforced with 1.60+0.2mm thick galvanised mild steel section made from roll forming process of required length ( shape and size according to upvc profile ) , upvc extruded beads of appropriate dimension of epdm gasket, gi fastners 100 x 8mm size for fixing frame to finished wall, plasyic packers, plastic caps and necessary stainless steel screws etc. profile of frame shall be mitred cut and fuson welded at all corners, mulion ( if required ) shall be also fusion welded including drilling of holes for fixing of hardwares and drainage of water etc. after fixing frame , the gap between frameand adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality , complete all as per approved drawing & direction of engineer in charge. ( glass or wire mesh shall be paid separately ) 152 taking down old unserviceable point wiring ( light, fan socket or power ) complete, including fixture and fittings such as switches, ceiling rose, pendents, regulators, sockets, light fittings etc.removing materials for keeping for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surface of walls floors etc. all as specified. 153 taking down old unserviceable submain wiring of any size including gi / copper earth continuity conductor in pvc conduit on wall / roof and making good to disturbed surfaces all as directed. 154 taking down ceiling fan, sealing cable end, dismantling blades from fan and keeping in safe custodyfor reuse at site andmaking good disturbed surfaces complete all as specified and as directed. 155 refixingonly ceiling fan with and including carrying out cleaning servicing, oiling and greasing of ceiling fans and connecting up including provision of cable from celling rose / connector to fan all as specified and as directed. 156 m& l painting of ceiling fan complete, in situ with synthetic enamal paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed. 157 disconnecting electric connection and taking down main switch / db of any size and keep in safe custody for taking credit complete and good / levelling the disturbed surfaces of wall to match with existing surface. 158 m&l for concealed point wiring complete with 1.5 sqmm single core pvc insulted frls cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia pvc rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling / roof / etc including 1.5 sqmm single core pvc insulated frls cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed for the following : ( a ) one light point controlled by one, one way switch. 159 ( b ) one ceiling / exhaust fan point controlled by one, one way switch. 160 ( c ) oneswitch socket outlet point 5 amps on independent board. 161 ( d ) one05 amps socket outlet pointon same board. 162 all as per item no.158 described here in before but with copper conductor cable frls, 4.00 sqmm for one 3 pin socket outlet, 15 amps and including 4 sqmm pvc insulated copper conductor cable as earth continuity conductor on independent board. 163 note for item no. 158 &159 : cutting chases and making good in wall / floor will be measured and paid seperately. 164 supply and fixing led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.make havells / bajaj / crompton 165 supply and fixing led light fitting mirror type withhigh out put diffuser 2 feet, 10 watt 220 v acdecorative type with driver holder and led lampincluding connecting up with three core flexiblecopper conductor cable of suitable size complete.make havells / bajaj / crompton 166 s & f led light fitting 1x9w / 1x10wbulkheadluminaires including led light driver holderconnecting up with three core flexible copperconductor cable of suitable size.make havells / bajaj / crompton 167 supply and fix mcb db, spn, 8 ways, isolated neutral bar with single doorip54 protection, door earthing arrangement with cement spill protector, mechanical impact strength ik09 complete. make: l&t / legrand / havells 168 supply and fix mcb spn 32 amps, 240volts, 10 ka, b curve complete. make: l&t / legrand / havells 169 supply and fix mcb sp 6 to 32 amps, 240volts, 10 ka, b curve complete. make: l&t / legrand / havells 170 supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals. 171 s&f modular fan regulator step type 120 w, 2 module complete all as specified and as directed. 172 s&f switch modular 6a single pole, one way, 1 module complete all as specified and as directed. 173 s&f switch modular 16a single pole, one way, 1 module complete all as specified and as directed. 174 s&f socket, 6a 2 / 3 pin combined 2 module complete all as specified and as directed. 175 s&f socket 6a / 16a 2 / 3 pin combined 2 module complete all as specified and as directed. 176 m&l for concealed sub main wiring by making recess in wall / surface complete with 2 runs of 6 sqmm single core pvc insulated frls cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 sqmm single core pvc insulated frls cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid pvc conduit and conduit accessories suface / concealed in wall / ceiling etcfor three phase sockets all as specified and as directed by engr in charge. note : 2 runs of 6 sqmm, + 1 run of 6 sqmm ( earth cotinuity conductor ) and 1 run of pvc conduit shall be measured as one unit length. 177 m & l earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 m below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead gi wire 4mm dia ( 8 swg ) connectd to gi earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board / feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and20mm bore medium grade gi pipewith funnel and wire mesh for watering including necessaryexcavation and earth works. pcc chamber in cement concrete 1:2:4 type b 1 & rcc cover and all as shown in electrical plate no. 3 of ssr ( part i ) of 2009. ( i ) the unit rate includes earthing wire, and protection pipe upto 7.5 metre. 178 cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; andcutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth 179 m& l for making opening for fixing of exhaust fan of size 300 mm sweep complete and making good the disturbed surface complete. 180 supply and fix exhaust fan, steel bodyac single phase. 230v of size 300msweep with, blades, and frame andlouvers 181 supply and fixing wall mounted fan 400 mm sweep, high speed, single phase, 230 volts , 50 hz complete. make havells / crompton / bajaj....

Rural Development And Panchayats Department - Tamil Nadu

40248397 tender for construction of pds building at sirulapattu village house of sirulapattu panchayat ; 2 earth work excavation and depositing on bank with intial lead and lift in all clasuses of soil such as hard gravely soil, gravely soil except hard rock requiring blasting etc complete as per ss20b for narrow foundation 3 supplying and filling in foundation and basement with filling m.sand including water consolidating etc., 4 supplying and filling of conveyed earth with a lead of 5km for basement filling 5 cement concrete 1:4:8 mix using 40mm isshbg stone jelly for foundation and flooring including cost, conveveyance of all materials and labour chargesto laid in layers not more than 15cm thick, well rammed etc, complete with standard specification 6 supplying and erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. rate for 10m2 for the following items ( rcc floor slab, roff slab, rectangular / square, tee / ell beams, lintels, staircase waist slablanding slab landing beam canopy etc in all floors with all cross bracings using mild steel sheets of size 90cm x 60cm and 10bg stiffened withmild steel angles of size 25mmx3mm for boarding laid over country wood joists of size 10cmx6.50cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre etc, complete and as directed. 7 below ground level 8 avove ground level 9 supplying, fabricatung and placin g in position of rts or ms rod for all reinforced cement concrete works as per design given including cost of steel and binding wire in all floors etc, complete complying with standard specification 10 reinforced cement concrete in 1 : 1.5 : 3 , mix using 20mm iss hbg stone jelly for all reinforced cement concrete works excluding cost of centering and stellbut including laying, vibrating, curing and finishing , fixing fan clamps in the rcc floor and roof slab works wherevver necessery and bearing surface of the wall at the sides and bottom of the slab, beam shall be finished smooth with cement mortor 1:3 and craft paper without claiming extra cost., complete compying with standard specification and as directed by the departmental officers 11 brick work in cement mortor 1 : 5 mix using country bricks of size 22 x 11 x 7 cm including cost and conveyance of all materials and labour charges etc complete 12 providing granolithic floor finish with cc 1:2:4 using 10 12mm hbg jelly 13 plastering with cement mortor 1:5, 12mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specificationas directed by the departmental officers 14 plastering with cement mortor 1:3 , 10mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specificationas directed by the departmental officers 15 supply of mild steel door of size 1.00 m x 2.10 m with two leaf. outer frame o f40 x 40x 6 mm equal ms angle, shutter frame made of 35 x325 x 5 mm equal ms angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using ms plate of size 20 x 5 mm fully covered with 18 gauge plain ms full sheet welded with shutter frame neatly and also fixin by welding, tower bolts 30 cm long , butt hingestwo nos of locking handles fixing the shutterincluding painting the whole unit with one coat of best quality red oxide primer . 16 supply of mild steel window of size 1.20 m x 1.30 m with two leaf. outer frame of 35 x 35 x 5 mm equal ms angle , mullion section made of 35 x 35 x 5 mm equal tee section , shutter frame made of 25 x 25 x 5 mm equal ms angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using ms plate of size 20 x 5 mm fully covered with 18 gauge plain ms full sheet welded with shutter frame neatly and also fixin by welding , protective grill with 12 mm square m s rods at an interval of not greater than 10 cm centre to centre to the outer frame , two nos peg stays with hole for keeping the windows open in different positions , two nos of locking handles fixing the shutter with four nos of hinges hold fasts , six nos of hinges with outter frame of the window including painting the whole unit with one coat of best quality red oxide primer . 17 supplying and fixing steel glazed ventilators with side hung swing shutter outer frame and shutter frames 18 supply of rolling shutter of size 1.20 m x 2.10 mwith frame and locking arrangements etc complete 19 white washing two coatsusing shell lime including cost and conveyance of all materials to site and all labour charges etc comopletefor 100 sqm 20 distembering two coats with best approved oil bound distember including cost of painting with primer coatover new plastered surface and conveyance of all materils to site and all labour charges etc complete 21 supplying and painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications ( the colour and shade of the cement paint shall be got approved by the executive engineer before use of work ) . 22 painting two coats over iron work including cost of paint and labour charges etc complete 23 provision for name board charges 24 provision for photographic charges...

Integral Coach Factory - Tamil Nadu

40202896 auction sale of description: scrap magnetic stainless steel shop refuse of various grades consisting of regular/irregular offcuts of sheets, plates, channels, pipes of all sorts, sizes and designs, punchings, remnants of punchings,window punchings of all sorts and sizes, small bits and strips of s.s magnetic variety, all rejected /obsolete fabricated magnetic stainless steel coach components generated from lhb unit,condemned /obsolete stainless steel seat,luggage and berth frames,pillar assembly,rejected and obsolete stainless steel coach components,stainless steel window punchings,handles of all sorts, shapes,obsolete stainless steel fasteners,couplings , unusable to icf.note: (1)full sheets excluded(2)any ferrous,non ferrous/plastic attachments can be removed at the time of delivery. (3) jcb permitted for spreading gst 18 percent.other taxes as applicable.gst and any other taxes as imposed by central or state government will be to buyer?s account? location bin no. 1, 2 & 3 and opposite side of bin no. 2 & 3 at east of shop 32. quantity 30000 kg.ul no 36 9809 0719 13 14.hsn code 720421....

Integral Coach Factory - Tamil Nadu

40065274 auction sale of description: scrap magnetic stainless steel shop refuse of various grades consisting of regular / irregular offcuts of sheets, plates, channels, pipes of all sorts, sizes and designs, punchings, remnants of punchings, window punchings of all sorts and sizes, small bits and strips of s.s magnetic variety, all rejected / obsolete fabricated magnetic stainless steel coach components generated from lhb unit, condemned / obsolete stainless steel seat, luggage and berth frames, pillar assembly, rejected and obsolete stainless steel coach components, stainless steel window punchings, handles of all sorts, shapes, obsolete stainless steel fasteners, couplings , unusable to icf.note: ( 1 ) full sheets excluded ( 2 ) any ferrous, non ferrous / plastic attachments can be removed at the time of delivery. ( 3 ) jcb permitted for spreading gst 18 percent.other taxes as applicable.gst and any other taxes as imposed by central or state government will be to buyer?s account?location north peripheral road at area opposite to street light pillar no 4 and street light pillar no 6. quantity 6000 kg.ul no 36 9809 0719 13 14.hsn code 720421....

Rural Development And Panchayats Department - Tamil Nadu

40004449 tender for reddiarchatram block tn 05 04; 1 1.construction of new anganwadi building at karattupatti h / o gurunadhanayakanurestimate amount rs.14.00 lakhs 2 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 3 cement concrete 1:4:8 mix using 40mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 4 filling in foundation and basement with redgravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 5 brick work in cement 1:5 mix using country bricks of size 23x11.5x7.5cms for the following including mixing mortar and all other labour charges etc. complete. 6 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 7 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 8 rcc 1:1.5:3 using 20mm hbg metal including cost and conveyance of materials and labour charges etc. complete 9 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 10 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no m.sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated to the required thickness & beating the concrete with wooden beaters of approved pattern as per std. specifications etc., complete. 11 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed neatly to full depth of tiles with same mortar as per std., specifications etc., complete. 12 paving the floor with eurocon tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 13 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 14 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 15 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 16 plastering with cm 1:4 mix 20mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 17 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 18 providing cuddapa slab including all charges etc. 19 iwc 20 ewc 21 supplying and fabrication of steel doord ( 1.00x2.10m ) 22 supplying and fabrication of steel doord ( 1.10x2.10m ) 23 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 24 supplying and fabrication of steel window w ( 1.2x1.3m ) 25 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 26 towards labour charges forfixing of steel doors, 27 towards labour charges forfixing of steel windows, & ventilators 28 supplying and fixing of rcc jolly including all charges etc 29 providing rain water pipe including all labour charges etc. 30 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments including all charges etc. 31 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 32 painting two coats over new iron work using synthetic enamel paint including cost and conveyace of all materials to site etc. complete. 33 painting two coats for black board including all charges etc. complete 34 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 35 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 36 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 37 supply and fixing of 14w cfl lamp for existing bh point. ( data b ) 38 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 39 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 40 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 41 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 42 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 43 supply and fixing of main service board.etc complete. 44 construction of rain water harvesting including all charges etc. 45 provision for water supply arrangement 46 provision for cartoon paintings 47 provision for handrails 48 provision for name board 49 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40004428 tender for reddiarchatram block tn 05 01; 1 1.construction of new anganwadi building at ad colony h / o t.pannaipattyestimate amount rs.14.00 lakhs 2 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 3 cement concrete 1:4:8 mix using 40mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 4 filling in foundation and basement with redgravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 5 brick work in cement 1:5 mix using country bricks of size 23x11.5x7.5cms for the following including mixing mortar and all other labour charges etc. complete. 6 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 7 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 8 rcc 1:1.5:3 using 20mm hbg metal including cost and conveyance of materials and labour charges etc. complete 9 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 10 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no m.sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated to the required thickness & beating the concrete with wooden beaters of approved pattern as per std. specifications etc., complete. 11 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed neatly to full depth of tiles with same mortar as per std., specifications etc., complete. 12 paving the floor with eurocon tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 13 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 14 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 15 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 16 plastering with cm 1:4 mix 20mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 17 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 18 providing cuddapa slab including all charges etc. 19 iwc 20 ewc 21 supplying and fabrication of steel doord ( 1.00x2.10m ) 22 supplying and fabrication of steel doord ( 1.10x2.10m ) 23 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 24 supplying and fabrication of steel window w ( 1.2x1.3m ) 25 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 26 towards labour charges forfixing of steel doors, 27 towards labour charges forfixing of steel windows, & ventilators 28 supplying and fixing of rcc jolly including all charges etc 29 providing rain water pipe including all labour charges etc. 30 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments including all charges etc. 31 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 32 painting two coats over new iron work using synthetic enamel paint including cost and conveyace of all materials to site etc. complete. 33 painting two coats for black board including all charges etc. complete 34 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 35 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 36 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 37 supply and fixing of 14w cfl lamp for existing bh point. ( data b ) 38 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 39 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 40 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 41 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 42 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 43 supply and fixing of main service board.etc complete. 44 construction of rain water harvesting including all charges etc. 45 provision for water supply arrangement 46 provision for cartoon paintings 47 provision for handrails 48 provision for name board 49 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 50 2.construction of new anganwadi building at old ad colonyh / o t.pannaipattyestimate amount rs. 14.00 lakhs 51 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 52 cement concrete 1:4:8 mix using 40mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 53 filling in foundation and basement with redgravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 54 brick work in cement 1:5 mix using country bricks of size 23x11.5x7.5cms for the following including mixing mortar and all other labour charges etc. complete. 55 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 56 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 57 rcc 1:1.5:3 using 20mm hbg metal including cost and conveyance of materials and labour charges etc. complete 58 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 59 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no m.sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated to the required thickness & beating the concrete with wooden beaters of approved pattern as per std. specifications etc., complete. 60 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed neatly to full depth of tiles with same mortar as per std., specifications etc., complete. 61 paving the floor with eurocon tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 62 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 63 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 64 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 65 plastering with cm 1:4 mix 20mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 66 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 67 providing cuddapa slab including all charges etc. 68 iwc 69 ewc 70 supplying and fabrication of steel doord ( 1.00x2.10m ) 71 supplying and fabrication of steel doord ( 1.10x2.10m ) 72 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 73 supplying and fabrication of steel window w ( 1.2x1.3m ) 74 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 75 towards labour charges forfixing of steel doors, 76 towards labour charges forfixing of steel windows, & ventilators 77 providing rain water pipe including all labour charges etc. 78 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments including all charges etc. 79 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 80 painting two coats over new iron work using synthetic enamel paint including cost and conveyace of all materials to site etc. complete. 81 painting two coats for black board including all charges etc. complete 82 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 83 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 84 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 85 supply and fixing of 14w cfl lamp for existing bh point. ( data b ) 86 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 87 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 88 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 89 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 90 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 91 supply and fixing of main service board.etc complete. 92 construction of rain water harvesting including all charges etc. 93 provision for water supply arrangement 94 provision for cartoon paintings 95 provision for handrails 96 provision for name board 97 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 98 3.construction of new anganwadi building at kuttiyapatty h / o ponnimandhuraiestimate amount rs. 14.00 lakhs 99 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 100 cement concrete 1:4:8 mix using 40mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 101 filling in foundation and basement with redgravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 102 brick work in cement 1:5 mix using country bricks of size 23x11.5x7.5cms for the following including mixing mortar and all other labour charges etc. complete. 103 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 104 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 105 rcc 1:1.5:3 using 20mm hbg metal including cost and conveyance of materials and labour charges etc. complete 106 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 107 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no m.sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated to the required thickness & beating the concrete with wooden beaters of approved pattern as per std. specifications etc., complete. 108 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed neatly to full depth of tiles with same mortar as per std., specifications etc., complete. 109 paving the floor with eurocon tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 110 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 111 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 112 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 113 plastering with cm 1:4 mix 20mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 114 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 115 providing cuddapa slab including all charges etc. 116 iwc 117 ewc 118 supplying and fabrication of steel doord ( 1.00x2.10m ) 119 supplying and fabrication of steel doord ( 1.10x2.10m ) 120 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 121 supplying and fabrication of steel window w ( 1.2x1.3m ) 122 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 123 towards labour charges forfixing of steel doors, 124 towards labour charges forfixing of steel windows, & ventilators 125 providing rain water pipe including all labour charges etc. 126 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments including all charges etc. 127 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 128 painting two coats over new iron work using synthetic enamel paint including cost and conveyace of all materials to site etc. complete. 129 painting two coats for black board including all charges etc. complete 130 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 131 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 132 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 133 supply and fixing of 14w cfl lamp for existing bh point. ( data b ) 134 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 135 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 136 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 137 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 138 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 139 supply and fixing of main service board.etc complete. 140 construction of rain water harvesting including all charges etc. 141 provision for water supply arrangement 142 provision for cartoon paintings 143 provision for handrails 144 provision for name board 145 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

40004297 tender for reddiarchatram block tn 05 03.; 1 1.construction of new anganwadi building at thethupatty h / o t.pannaipattyestimate amount rs.14.00 lakhs 2 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 3 cement concrete 1:4:8 mix using 40mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 4 filling in foundation and basement with redgravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 5 brick work in cement 1:5 mix using country bricks of size 23x11.5x7.5cms for the following including mixing mortar and all other labour charges etc. complete. 6 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 7 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 8 rcc 1:1.5:3 using 20mm hbg metal including cost and conveyance of materials and labour charges etc. complete 9 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 10 providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime ( no m.sand to be used ) over the roof slab in the proportion of brickjelly lime 32:121 / 2 by volume and laid over in a single layer and consolidated to the required thickness & beating the concrete with wooden beaters of approved pattern as per std. specifications etc., complete. 11 finishing the top of roof with one course of machine pressed tiles of size 20cmx20cmx20mm of approved quality laid in cement mortar 1:3 mix to 12mm thick mixed with water proofing compound confirming to iss by 2% weightof cement used and the joint pointed neatly to full depth of tiles with same mortar as per std., specifications etc., complete. 12 paving the floor with eurocon tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 13 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 14 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 15 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 16 plastering with cm 1:4 mix 20mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 17 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 18 providing cuddapa slab including all charges etc. 19 iwc 20 ewc 21 supplying and fabrication of steel doord ( 1.00x2.10m ) 22 supplying and fabrication of steel doord ( 1.10x2.10m ) 23 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 24 supplying and fabrication of steel window w ( 1.2x1.3m ) 25 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 26 towards labour charges forfixing of steel doors, 27 towards labour charges forfixing of steel windows, & ventilators 28 supplying and fixing of rcc jolly including all charges etc 29 providing rain water pipe including all labour charges etc. 30 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments including all charges etc. 31 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 32 painting two coats over new iron work using synthetic enamel paint including cost and conveyace of all materials to site etc. complete. 33 painting two coats for black board including all charges etc. complete 34 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 35 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 36 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 37 supply and fixing of 14w cfl lamp for existing bh point. ( data b ) 38 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 39 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 40 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 41 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 42 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 43 supply and fixing of main service board.etc complete. 44 construction of rain water harvesting including all charges etc. 45 provision for water supply arrangement 46 provision for cartoon paintings 47 provision for handrails 48 provision for name board 49 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

39803226 tender for construction of public distribution shop at chockanavur panchayat. ; 2 earth work excavation for foundation in all clauses of soils and sub soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and boiling out water whenever necessary et complete complying with standard specification. 3 supplying and filling with msand in layers of not more than 15 cm thick for foundation including cost and conveyance of all materials and labour charges other charges. 4 refillingthe basement with excavated earth including all labour charges for filling as per standard specifications 5 cement concrete 1:4:8 mix ( one cement four sand and eight aggregate ) using 40mm gauge handbroken granite stone jelly for foundation including dewatering if found ecessary and laid in layers of not more than 15 cm thick and compacted, etc., complete complying withstandard specfication. 6 brick work in cement mortar 1:5 mix using country bricks 83 / 4x41 / 4x21 / 4 including cost and conveyance of all materials to site and all labour charges etc complete ( below basement ) 7 brick work in cement mortar 1:5 mix using country bricks 83 / 4x41 / 4x21 / 4 including cost and conveyance of all materials to site and all labour charges etc complete above basement ) 8 supplying and erecting centering for sides and soffits of rcc slabs of plane surface like lintels, beams etc., including strutting 3m high using mild steel sheets of size 90cm x60cm x and b.g 10 stiffened with m.s angles of size 25mm x 25mm x 3mm laid over silver oak ( c.w ) joists of size 10cm x 6.5cm ( spaced at about 90cm c / c ) and supported dy casurina props of 10cm to 13cm dia ( spaced of 75cm c / c ) complying with standard specification. 9 below basement 10 above basement with roof slab 11 suppling, fabricating and placing in position of ms ( or ) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors as per standard specification. 12 reinforced cement concrete 1:1.5:3 ( one cement, one and halfsand &three course aggregate ) using 20mm gauge hand broken / hard granite blue stone for all rccitemsof works excluding centering shuttering and cost of reinforcement but including curing etc., complete as directed by departmentalofficer etc., complete. 13 floor finish with granolithic flooring in cc 1:2:4 mix using 10 to 12mm chipsfor 40mm thick including cost and conveyance of all materials to site and all labour charges etc., complete complying with standard specifications and as directed by the department 14 paving the floor with pre polished concrete anti skid tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 15 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and threesand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) 16 dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in cement mortar 1:2 ( one cement and two crushed stone sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 17 plastering with cm 1:5, 12mm thick inculding cost and conveyance of all materials to site and all labour charges etc., complete 18 plastering with cm 1:3, 10mm thick inculding cost and conveyance of all materials to site and all labour charges etc., complete 19 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three crushed stonesand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 20 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 21 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 22 manufacturing supplying and fixing of steel door with the following specification ms angels of size 40x40x6mm are used for the outer frames and m.s. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm m.s flat is provided at required intervals in the shutter frame. 18 gauge c.r. sheet laid as panel in the shutter and welded intact. m.s. flat 18x5mm is welded over the 32 x 6mm m.s. flat sandwitching the c.r. sheet in between additional stiffeners with 18x5mm m.s. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. tower bolts 2nos. one at the top and the other at the bottom are provided 1no. aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door one rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place.incase of double leaf door m.s.flat 32 x 3mm at 1.1kg / m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. a tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. all members are given a coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete. 23 providing steel door 1 ( 1.00mx2.100m ) 24 toilet doors d 2 steel ( 0.900mx2.100m ) 25 providing steel window ( 1.00x1.30m ) 26 providing steel ventilator ( 0.900x0.600m ) 27 providing rolling shutter ( 1.80x2.40m ) 28 providing rolling shutter ( 2.10x2.40m ) 29 painting two coats over new iron works using ready mixed enamel paint including cost and conveyance of paint and all labour charges etc complete 30 labour charges for fixing the doors inculding all charges etc.. 31 labour charges for fixing the steel window and ventilator inculding all charges etc.. 32 supplying & fixingwith cuddapah slabs 20 30mm thick for cup board including all cost and conveyance and all labour charges etc .comp. 33 supplying and fixingp.v.c rainwater down fall pipe of 110mm dia 34 providing vargapoochu over the cre walls of vimanams / gopurams, with cement mortar 1:4 complete including shaping the mukhapathram , mahanasi, koodu all ornamentals works to proper shape by embedding broken brick of shaped / chiseled bricks , rought plastering with cement morter 1:4 and finishing with final ornamental plastering and nayam theervani icluding cost and conveyance of all materials , labour therefore, lifting of materials , all working in heights, curing with water etc, complete including all extra for folding and including clearing from the vimanams / gopurams 100sft superficial area. for kalkaram 35 kalkaram 36 for vimanam 37 supplying and fixing in positon indian water closet ( oriya type ) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with p or s trap conforming to bis etc., complete complying with standard specifications and as directed by the departmental officers. 38 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Integral Coach Factory - Tamil Nadu

39507072 auction sale of description: scrap magnetic stainless steel shop refuse of various grades consisting of regular / irregular offcuts of sheets, plates, channels, pipes of all sorts, sizes and designs, punchings, remnants of punchings, window punchings of all sorts and sizes, small bits and strips of s.s magnetic variety, all rejected / obsolete fabricated magnetic stainless steel coach components generated from lhb unit, condemned / obsolete stainless steel seat, luggage and berth frames, pillar assembly, rejected and obsolete stainless steel coach components, stainless steel window punchings, handles of all sorts, shapes, obsolete stainless steel fasteners, couplings , unusable to icf.note: ( 1 ) full sheets excluded ( 2 ) any ferrous, non ferrous / plastic attachments can be removed at the time of delivery. ( 3 ) jcb permitted for spreading gst 18 percent.other taxes as applicable.gst and any other taxes as imposed by central or state government will be to buyer?s account?location north side of old scrap ward office extending up to north side of room nos 9ab and 16ab ( south side of bin nos 21, 22& 23 ) quantity 40000 kg.ul no 36 9809 0719 13 14.hsn code 720421....

Public Works Department - Tamil Nadu

38921318 construction of 6 class room building in gghss at sankarapuram in kallakurichi district. 1 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 2 supplying and filling in foundation, basement, etc with filling crushed stone stand (m sand) and in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 3 supplying and filling ofgravel by lorry in basement filling including stacking for premeasurement, conveyance loading and unloading charges and all other incidential charges and including filling laying watering and consolidating etc., complete as directed by the dept., officers and complying with standard specification. (5km lead) 4 refilling in basement with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification. 5 cement concrete 1:5:10 (one cement, five m sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification. 6 cement concrete 1:5:10 (one cement, five m sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for flooring including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification. 7 brick work using best quality of second class ground moulded chamber burnt bricks of size 9 x 4 3/8 x 2 3/4 in cement mortar 1:5 (one cement and five m sand) includingneat finishing,curingetc,complete complying with standard specification. 8 for foundation and basement 9 brick work in cement mortar 1:6 [ one cement and six m sand] using best quality of second class ground moulded chamber burnt bricks of size 9 x 43/8 x 23/4 for foundation and basement including curing, etc., complete complying with standard specifiction. 10 for foundation and basement 11 for superstructure in ground floor 12 for superstructure in first floor 13 for superstructure in second floor 14 brick partition walls of 11.50 cmthickness using best quality of second class ground moulded chamber burnt bricks of size 9 x 4 3/8 x 2 3/4 in cement mortar 1:3 (one cement and three m sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (hoop iron reinforcement will be measured and paid for separately) 15 for superstructure in ground floor 16 for superstructure in first floor 17 damp proof course with cement mortar 1:4 (one cement and four m sand) 12mm thick mixed with best approved quality water proofing compound conforming to indian standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification. 18 supplying and erecting steel centering including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete. 19 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete 20 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 21 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 22 providing and laying in position, standardised concrete mix m 2o grade in accordance with is 456 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg/cu.m and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials). 23 for foundation and basement 24 for superstructure in ground floor 25 for superstructure in first floor 26 for superstructure in second floor 27 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 28 plain cement concrete 1:2:4 (one cement, two m sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. 29 paving with rubber moulded hydraulically pressed paver block with pattern design of 50% colour and 50% plain of 83 mm of approved quality and colour, over the sand filling to full depth of slab perfectly and neat finishing the joints, compressing with vibrator. the rate shall be inclusive of cost of paver block, taxes, incidental charges, transportion charges and labour charges for fixing, neat finishing the joints as directed by the departmental officers etc., complete complying with standard specification. the paver block should got approved by the departmental officers before use on works 30 paving the top of roof with solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three m sand) 12mm thick and pointed with tile grout (nitotile grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. the make and brand of the tiles should got approved by the executive engineer before use on works. 31 paving the floor with best approved quality fine polished kota stone slabs of size above 600 x 600 of 20mm with machine cut edges and matching marble slab not less than 100mm width other than adanga marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (one cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., complete as per standard speicification. 32 paving the floor(staircase steps ) with kota stone below600mm x 600mm x20 mmdesign) of 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three m sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete. 33 supplying and fixing fine polished cuddapah slab of 38 / 40mm thickness for cup board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct. 34 supplying and fixing of unbreakable dust free, easy to erase ,class room writing board of size 3.60mx1.20m made up 8mm thick green colour ceramic sheet pasted on the front side 12mm thick ply board and backside of ply board is pasted with flex board sheet the outer beading of the writing board will be fixed with aluminium hi section of size 25mm, the board will be fixed firmly on the wall using 3 inch screws the rates includes cost of all materials labour approved quality, etc., complete complying with standard specifications and as directed by departmental officers excluding gst. 35 plastering with cement mortar 1:5 (one cement and five m sand), 12mm thick mixed with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 36 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (one cement and three m sand) 10mm thick mixed with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers. 37 supplying and fixing in position best approved of bis quality of following dia pvc rain water down fall pipes having a pressure of 4kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 38 110mm dia (two floors) 39 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 40 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 41 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 42 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg/m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frame.stiffeners with 32x6mm at 1.5 kg/m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 g cr sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m ms flat is welded over the 32x6mm at 1.50kg/m ms flat on the rear side of the door, sandwitching the cr sheet for rigidity.additional stiffeners with 18x5mm at 0.7 kg/m ms flats are provided diagonally on the rear side of the shutter.300mm length of hinges 2 nos, for shutter is provided.6 nos.of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. tower bolt 2 nos. at the top provided.250x16mm size of two aldrops are provided in single leaf door at lock rail section in the door for inner and outer provided and one rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear sideof the door at an appropriate place and 1 no. of m.s. handle of heavy duty. a tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. 43 single leaf 44 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg/m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frame.stiffeners with 32x6mm at 1.5 kg/m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 g cr sheets of best quality is laid as panel in the shutter frames.18x5mm at 0.70 kg/m ms flat is welded over the 32x6mm at 1.50kg/m ms flat on the rear side of the door, sandwitching the cr sheet for rigidity.additional stiffeners with 18x5mm at 0.7 kg/m ms flats are provided diagonally on the rear side of the shutter. 300mm length of highes 4 nos. for shutters is provided.6 nos. of hold fasts 200mm length spliced at the ends are welded to the outer frame of the door. 250mm lenght of tower bolt 2 nos., one at the top and the other at bottom are provided.250x16mm size of one aldrop is provided in case of double leaf door at lock rail section in the door. additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate placeand 2 nos. ms handles of heavy duty .ms flat 32x4mm at 1.10 kg/m is provided on the edge of the one shutter to conceal the gap between the two shutters. a tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.all members are given one coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. 45 double leaves 46 manufacturing, supplying and fixing of steel door emergency exit with the following specifications, ms angle of size 40 x 40 x 6mm at 3.5 kg/m are used for outer frames and ms angle of size 35 x 35 x 5mm at 2.6 kg/m for the shutter frames.stiffeners with ms flat 32 x 6mm at 1.50 kg / m is provided for fixing the aldrop for the door and welded intact 18 gauge cr sheet is laid as panel in the shutters and welded intact of 1/3 bottom portion of the shutters, 2/3 portion at top provided with ms grill at 15 kg/sq.m as per design and laid as panel in the shutters.the openable shutter also provided to cover the 2/3 grill portion with 18 gauge cr sheet with shutter frame made out of ms angle of size 35 x 35 x 5mm @ 2.60 kg / m. and stiffeners with ms flat of of size 32x6mm at 1.5 kg/m.the additional stiffeners of size 18x5mm at 0.70 kg/m is welded intact with door shutter.necessary furniture fittings also provided for this shutter as directed by the departmental officers.necessary ‘j’ section having ms angle 46 x 25 x 3mm at 2.28 kg/m is provided in between ms grill and cr sheet ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability. 47 ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability.ms flat 32 x 4mm at 1.10 kg/m is provided over the edge of one shutter in case of double door, to conceal the gap between the shutters.2 nos. of 300mm length of hinges in case of single leaf door and 4 nos. of 300mm length of hinges in case of double leaf doors are provided at an appropriate place in the outer frame.6 nos. of hold fasts of 200mm in length spliced at the ends are welded to the outer frame of the door. 250mm length of tower bolts 4 nos. one at top and the other at the bottom are provided. in case of double leaf door one number aldrop is provided at an appropriate place in the doors; two numbers of 250x16mm length and 2 nos. of handle heavy duty aldrop in single leaf door.a tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, taxes,transportation to site of work, loading, unloading and all other incidental charge, etc., complete. 48 double leaves 49 manufacturing, supplying and fixing in position of steel windows with the following specifications.outer frames of windows made of z section f7d of size 33 x 25 x 3 mm at 1.419 kg/m and mullion o section (f4b) of size 46 x 25 x 3 mm at 2.28 kg/m and shutter section of made of f7d of 33 x 25 x 3 mm at 1.419 kg/m as specified in is 7452/1990.each openable shutter should not exceed a width of 600 mm to enable separate operations and easy maintenance.the panel of the shutter to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. horizontal stiffeners using 18 x 5 mm ms flat at 0.70 kg/m at 3 nos for each shutters and additional diagonal stiffeners of the same ms flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the cr sheets in position firmly. 50 4 numbers of sturdy hinges and two number of handle cum latch of special type made with 18x5mm ms flats are revetted to the shutters at an appropriate height in window.suitable opening is left for its easy operation.a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle.each window shutter having an adjustable stay made out of 18x5mm at 0.70 kg/m ms flat of length 320mm with three adjustable position.a matching peg is provided in the outer frame of the window at suitable place.4 nos. of hold fasts of 120mm length spliced at the ends are welded to the out frame of the window by using ms flat of 18x5 mm at 0.70 kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter. an ms square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge to edge between them.all members are painted with one coat of anti corrosive red oxide primer as directed by the departmental officers.all sections should be in confirmed with is7452/1990. the cost includes cost of all materials, labour charges and other incidental charges, etc., complete. 51 fourleaves 52 supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of ms flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete.an additional ms flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers. 53 supplying and fixing 40mm dia gi pipe for staircase hand rail including labour charges for cutting, welding and fixing with ms flats (excluding cost of flat), etc., as directed by the departmental officers 54 supplying and fixing by drilling holes and not by puching for roofing with pre painted galvalum sheet of0.47mm thick of best approved quality with required size with curved shape and white ridge sheet with necessary bolts and nuts bitumen washers, including cutting the sheet to the required size found necessary during execution etc., complete complying with standard specifications. [the sheet should be got approved by the engineer incharge before use on works] 55 supplying and fixing of m.s.grill of approved design for grill gate, grill work to doors and windows openings ramp etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification. 56 providing pre construction anti termite treatment for the building including all chemicals as per standard specifications. labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. the rate shall be inclusive ofgiving anti termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12to a depth of 8 in the periphery of building and pouring chemicals etc., complete as per isi 6313 1981 and. the antitermite chemicals used should have 0.5% concentration with 3l solution for the entire operation etc. as directed by the engineer incharge and including cost of chemicals labour transportion etc, stage:1 spraying anti termite treatement chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation.stage:2 spraying anti termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth.stage:3 spraying anti termite chemicals solution on sand for the flooring before laying the flooring concrete. the treatment has to be carried out on the sand filling the basement after leveling operation is over.stage:4 spraying anti termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12 to a depth of 8 around the building before laying the plinth projection.this holes has to be be closed after the treatment. ...

Public Works Department - Tamil Nadu

38921253 construction of 4 class room building in ghss at karadichithur in kallakurichi district. 1 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete. 2 supplying and filling in foundation, basement, etc with filling crushed stone sand (m sand) and in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 3 supplying and filling ofgravel by lorry in basement filling including stacking for premeasurement, conveyance loading and unloading charges and all other incidential charges and including filling laying watering and consolidating etc., complete as directed by the dept., officers and complying with standard specification. 4 refilling in basement with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 5 cement concrete 1:5:10 (one cement, five m sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 6 cement concrete 1:5:10 (one cement, five m sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for flooringincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 7 brick work in cement mortar 1:5 [ one cement and five m sand] using best quality of second class ground moulded chamber burnt bricks of size 9 x 43/8 x 23/4 for foundation and basement including curing, etc., complete complying with standard specifiction. 8 for foundation and basement 9 brick work in cement mortar 1:6 [ one cement and six m sand] using best quality of second class ground moulded chamber burnt bricks of size 9 x 43/8 x 23/4 for foundation and basement including curing, etc., complete complying with standard specifiction. 10 for foundation and basement 11 for superstructure in ground floor 12 for superstructure in first floor 13 brick partition walls of 11.50 cmthickness using best quality of second class ground moulded chamber burnt bricks of size 9 x 4 3/8 x 2 3/4 in cement mortar 1:3 (one cement and three m sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (hoop iron reinforcement will be measured and paid for separately) 14 for superstructure in ground floor 15 for superstructure in first floor 16 damp proof course with cement mortar 1:4 (one cement and four m sand) 12mm thick mixed with best approved quality water proofing compound conforming to indian standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification. 17 supplying and erecting steel centering including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (payment for centering shall be given after the concrete is laid) 18 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (payment for centering shall be given after the concrete is laid) 19 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 20 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 21 providing and laying in position, standardised concrete mix m 20 grade in accordance with is 456 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg/cu.m and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials). 22 for foundation and basement 23 for superstructure in ground floor 24 for superstructure in first floor 25 for superstructure in second floor 26 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification.(contractor has to make his own arrangements for the supply of steel and binding wire) 27 plain cement concrete 1:2:4 (one cement, two m sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. 28 paving the top of roof with solar reflective ceramic tiles (required design) of 305x305x7mm thick of approved quality and collour laid in cement mortar 1:3 (one cement and three m sand) 12mm thick and pointed with tile grout (nitotile) grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc, complete complying with standard specification as directed by the departmental officers.(the make and brand of the tiles should be got approved by executive engineer before use on works) 29 paving the floor with best approved quality fine polished kota stone slabs of size above 600 x 600 of 20mm with machine cut edges and matching marble slab not less than 100mm width other than adanga marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (one cement and three m sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., complete as per standard speicification. 30 paving the floor(staircase steps ) with kota stone below 600mm x 600mm x20 mmdesign) of 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three m sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete. 31 supplying and fixing fine polished cuddapah slab of 38/40mm thickness for cup board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct. 32 supplying and fixing of unbreakable dust free, easy to erase ,class room writing board of size 3.60mx1.20m made up 8mm thick green colour ceramic sheet pasted on the front side 12mm thick ply board and backside of ply board is pasted with flex board sheet the outer beading of the writing board will be fixed with aluminium hi section of size 25mm, the board will be fixed firmly on the wall using 3 inch screws the rates includes cost of all materials labour approved quality, etc., complete complying with standard specifications and as directed by departmental officers excluding gst. 33 plastering with cement mortar 1:5 (one cement and five m sand), 12mm thick mixed with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 34 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (one cement and three m sand) 10mm thick mixed with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers. 35 plastering the surface of walls with cement mortar 1:3 (one cement and three m sand), 12mm thick mixed with water proofing compound conforming to bis at 2% by weight of cement and with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers. 36 supplying and fixing in position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 37 110mm dia (one floor) 38 110mm dia (two floors ) 39 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (the colour and shade of the distemper shall be got approved by the executive engineer before use of work). 40 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 41 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (the make, quality and colour of paint should be got approved by the executive engineer before use on works.) 42 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg/m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frame.stiffeners with 32x6mm at 1.5 kg/m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 g cr sheets of best quality is laid as panel in the shutter frames.18x5mm at 0.70 kg/m ms flat is welded over the 32x6mm at 1.50kg/m ms flat on the rear side of the door, sandwitching the cr sheet for rigidity.additional stiffeners with 18x5mm at 0.7 kg/m ms flats are provided diagonally on the rear side of the shutter.300mm length of hinges 2 nos, for shutter is provided.6 nos.of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. tower bolt 2 nos. at the top provided. 250x16mm size of two aldrops are provided in single leaf door at lock rail section in the door for inner and outer provided and one rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place and 1 no. of m.s. handle of heavy duty. a tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. 43 single leaf 44 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg/m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frame.stiffeners with 32x6mm at 1.5 kg/m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 g cr sheets of best quality is laid as panel in the shutter frames.18x5mm at 0.70 kg/m ms flat is welded over the 32x6mm at 1.50kg/m ms flat on the rear side of the door, sandwitching the cr sheet for rigidity.additional stiffeners with 18x5mm at 0.7 kg/m ms flats are provided diagonally on the rear side of the shutter.300mm length of hinges 4 nos. for shutters is provided.6 nos. of hold fasts 200mm length spliced at the ends are welded to the outer frame of the door. 250mm length of tower bolt 2 nos., one at the top and the other at bottom are provided.250x16mm size of one aldrop is provided in case of double leaf door at lock rail section in the door.additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place and 2 nos. ms handles of heavy duty .ms flat 32x4mm at 1.10 kg/m is provided on the edge of the one shutter to conceal the gap between the two shutters. a tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.all members are given one coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. 45 double leaves 46 manufacturing, supplying and fixing of steel entrance door with the following specifications, ms angle of size 40 x 40 x 6mm at 3.5 kg/m are used for outer frames and ms angle of size 35 x 35 x 5mm at 2.6 kg / m for the shutter frames.stiffeners with ms flat 32 x 6mm at 1.50 kg / m is provided for fixing the aldrop for the door and welded intact 18 gauge cr sheet is laid as panel in the shutters and welded intact of 1/3 bottom portion of the shutters, 2/3 portion at top provided with ms grill at 20 kg/sq.m as per design and laid as panel in the shutters.necessary ‘j’ section having ms angle 46 x 25 x 3mm at 2.28 kg/m is provided in between ms grill and cr sheet for compact fixing of the grill and sheet in position.the design and style for the upper panel should be approved by the departmental officers.ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability. 47 ms flat 32 x 4mm at 1.10 kg/m is provided over the edge of one shutter in case of double door, to conceal the gap between the shutters.300mm length of hinges 4 nos., are provided at an appropriate place in the outer frame.6 nos. of hold fasts of 200mm in length spliced at the ends are welded to the outer frame of the door.250mm length of tower bolts 2 nos. one at top and the other at the bottom are provided.250x16mm one number aldrop is provided at an appropriate place in the doors;2 nos. of ms handles of heavy duty. a tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, taxes, transportation to site of work, loading, unloading and all other incidental charge, etc., complete. 48 double leaves 49 manufacturing, supplying and fixing of steel door emergency exit with the following specifications, ms angle of size 40 x 40 x 6mm at 3.5 kg/m are used for outer frames and ms angle of size 35 x 35 x 5mm at 2.6 kg/m for the shutter frames.stiffeners with ms flat 32 x 6mm at 1.50 kg / m is provided for fixing the aldrop for the door and welded intact 18 gauge cr sheet is laid as panel in the shutters and welded intact of 1/3 bottom portion of the shutters, 2/3 portion at top provided with ms grill at 15 kg/sq.m as per design and laid as panel in the shutters.the openable shutter also provided to cover the 2/3 grill portion with 18 gauge cr sheet with shutter frame made out of ms angle of size 35 x 35 x 5mm @ 2.60 kg / m. and stiffeners with ms flat of of size 32x6mm at 1.5 kg/m.the additional stiffeners of size 18x5mm at 0.70 kg/m is welded intact with door shutter.necessary furniture fittings also provided for this shutter as directed by the departmental officers.necessary ‘j’ section having ms angle 46 x 25 x 3mm at 2.28 kg/m is provided in between ms grill and cr sheet ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability. 50 ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability.ms flat 32 x 4mm at 1.10 kg/m is provided over the edge of one shutter in case of double door, to conceal the gap between the shutters.2 nos. of 300mm length of hinges in case of single leaf door and 4 nos. of 300mm length of hinges in case of double leaf doors are provided at an appropriate place in the outer frame.6 nos. of hold fasts of 200mm in length spliced at the ends are welded to the outer frame of the door. 250mm length of tower bolts 4 nos. one at top and the other at the bottom are provided. in case of double leaf door one number aldrop is provided at an appropriate place in the doors; two numbers of 250x16mm length and 2 nos. of handle heavy duty aldrop in single leaf door.a tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, taxes,transportation to site of work, loading, unloading and all other incidental charge, etc., complete. 51 double leaves 52 manufacturing, supplying and fixing in position of steel windows with the following specifications.outer frames of windows made of z section f7d of size 33 x 25 x 3 mm at 1.419 kg/m and mullion o section (f4b) of size 46 x 25 x 3 mm at 2.28 kg/m and shutter section of made of f7d of 33 x 25 x 3 mm at 1.419 kg/m as specified in is 7452/1990.each openable shutter should not exceed a width of 600 mm to enable separate operations and easy maintenance.the panel of the shutter to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. horizontal stiffeners using 18 x 5 mm ms flat at 0.70 kg/m at 3 nos for each shutters and additional diagonal stiffeners of the same ms flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the cr sheets in position firmly. 53 4 numbers of sturdy hinges and two number of handle cum latch of special type made with 18x5mm ms flats are revetted to the shutters at an appropriate height in window.suitable opening is left for its easy operation.a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle.each window shutter having an adjustable stay made out of 18x5mm at 0.70 kg/m ms flat of length 320mm with three adjustable position.a matching peg is provided in the outer frame of the window at suitable place.4 nos. of hold fasts of 120mm length spliced at the ends are welded to the out frame of the window by using ms flat of 18x5 mm at 0.70 kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter. an ms square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge to edge between them.all members are painted with one coat of anti corrosive red oxide primer as directed by the departmental officers.all sections should be in confirmed with is7452/1990. the cost includes cost of all materials, labour charges and other incidental charges, etc., complete. 54 fourleaves 55 supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of ms flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete.an additional ms flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers. 56 supplying and fixing 40mm dia gi pipe for staircase hand rail including labour charges for cutting, welding and fixing with ms flats (excluding cost of flat), etc., as directed by the departmental officers 57 supplying and fixing of m.s.grill of approved design for grill gate, grill work to doors and windows openings ramp etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification. 58 providing pre construction anti termite treatment for the building including all chemicals as per standard specifications. labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. the rate shall be inclusive ofgiving anti termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12to a depth of 8 in the periphery of building and pouring chemicals etc., complete as per isi 6313 1981 and. the antitermite chemicals used should have 0.5% concentration with 3l solution for the entire operation etc. as directed by the engineer incharge and including cost of chemicals labour transportion etc, stage:1 spraying anti termite treatement chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation.stage:2 spraying anti termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth.stage:3 spraying anti termite chemicals solution on sand for the flooring before laying the flooring concrete. the treatment has to be carried out on the sand filling the basement after leveling operation is over.stage:4 spraying anti termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12 to a depth of 8 around the building before laying the plinth projection.this holes has to be be closed after the treatment. ...

Public Works Department - Tamil Nadu

38921225 construction of 4 class room building in a.s.government girls higher secondary school at tirukoilur in kallakurichi district. 1 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 2 earth work open excavation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling crushed stone sand (m sand) and in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 supplying and filling ofgravel by lorry in basement filling including stacking for premeasurement, conveyance loading and unloading charges and all other incidential charges and including filling laying watering and consolidating etc., complete as directed by the dept., officers and complying with standard specification. 5 refilling in basement with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 6 cement concrete 1:5:10 (one cement, five m sand and ten hard broken stonejelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification. 7 cement concrete 1:5:10 (one cement, five msand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for flooring including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification. 8 brick work in cement mortar 1:3 [ one cement and three m sand] using best quality of second class ground moulded chamber burnt bricks of size 9 x 43/8 x 23/4 for foundation and basement including curing, etc., complete complying with standard specifiction. 9 for foundation and basement 10 brick work in cement mortar 1:5 [ one cement and five m sand] using best quality of second class ground moulded chamber burnt bricks of size 9 x 43/8 x 23/4 for foundation and basement including curing, etc., complete complying with standard specifiction. 11 for foundation and basement 12 brick work in cement mortar 1:6 [ one cement and six m sand] using best quality of second class ground moulded chamber burnt bricks of size 9 x 43/8 x 23/4 for foundation and basement including curing, etc., complete complying with standard specifiction. 13 for foundation and basement 14 for superstructure in ground floor 15 for superstructure in first floor 16 for superstructure in second floor 17 brick partition walls of 11.50 cmthickness using best quality of second class ground moulded chamber burnt bricks of size 9 x 4 3/8 x 2 3/4 in cement mortar 1:3 (one cement and three m sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (hoop iron reinforcement will be measured and paid for separately) 18 for superstructure in ground floor 19 for superstructure in first floor 20 damp proof course with cement mortar 1:4 (one cement and four m sand) 12mm thick mixed with best approved quality water proofing compound conforming to indian standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification. 21 supplying and erecting steel centering including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (payment for centering shall be given after the concrete is laid) 22 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (payment for centering shall be given after the concrete is laid) 23 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 24 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 25 providing and laying in position, standardised concrete mix m 20 grade in accordance with is 456 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg/cu.m and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials). 26 for foundation and basement 27 for superstructure in ground floor 28 for superstructure in first floor 29 for superstructure in second floor 30 manufacturing, supplying and fixing precast reinforced cement concrete slabs of following thickness in rcc 1:2:4 (one cement, two m sand and four aggregates), using 20mm hbgs jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed. 31 for 50mm thick slab 32 for 75mm thick slab 33 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification.(contractor has to make his own arrangements for the supply of steel and binding wire) 34 paving the top of roof with solar reflective ceramic tiles (required design) of 305x305x7mm thick of approved quality and collour laid in cement mortar 1:3 (one cement and three m sand) 12mm thick and pointed with tile grout (nitotile) grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc, complete complying with standard specification as directed by the departmental officers.(the make and brand of the tiles should be got approved by executive engineer before use on works) 35 paving the floor with best approved quality fine polished kota stone slabs of size above 600 x 600 of 20mm with machine cut edges and matching marble slab not less than 100mm width other than adanga marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (one cement and three m sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (one cement and three m sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., the kota stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work, etc., complete as per standard speicification. 36 paving the floor(staircase steps ) with kota stone below 600mm x 600mm x20 mmdesign) of 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three m sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete. 37 supplying and fixing fine polished cuddapah slab of 38/40mm thickness for cup board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct. 38 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (one cement, two m sand and four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (the rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers) 39 for 40mm thick 40 supplying and fixing of unbreakable dust free, easy to erase ,class room writing board of size 3.60mx1.20m made up 8mm thick green colour ceramic sheet pasted on the front side 12mm thick ply board and backside of ply board is pasted with flex board sheet the outer beading of the writing board will be fixed with aluminium hi section of size 25mm, the board will be fixed firmly on the wall using 3 inch screws the rates includes cost of all materials labour approved quality, etc., complete complying with standard specifications and as directed by departmental officers excluding gst. 41 plastering with cement mortar 1:5 (one cement and five m sand), 12mm thick mixed with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 42 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (one cement and three m sand) 10mm thick mixed with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers. 43 plastering the surface of walls with cement mortar 1:3 (one cement and three m sand), 12mm thick mixed with water proofing compound conforming to bis at 2% by weight of cement and with bonding agent cebex112, zydex zycrete 2x or other equalent compound conforming to bis at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers. 44 supplying and fixing in position best approved of bis quality of following dia pvc rain water down fall pipes having a pressure of 4kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 45 110mm dia pvc pipe (two floors) 46 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (the colour and shade of the distemper shall be got approved by the executive engineer before use of work). 47 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 48 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (the make, quality and colour of paint should be got approved by the executive engineer before use on works.) 49 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg/m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frame.stiffeners with 32x6mm at 1.5 kg/m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 g cr sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m ms flat is welded over the 32x6mm at 1.50kg/m ms flat on the rear side of the door, sandwitching the cr sheet for rigidity.additional stiffeners with 18x5mm at 0.7 kg/m ms flats are provided diagonally on the rear side of the shutter.300mm length of hinges 2 nos, for shutter is provided.6 nos.of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. tower bolt 2 nos. at the top provided.250x16mm size of two aldrops are provided in single leaf door at lock rail section in the door for inner and outer provided and one rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear sideof the door at an appropriate place and 1 no. of m.s. handle of heavy duty. a tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. 50 single leaf 51 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg/m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frame.stiffeners with 32x6mm at 1.5 kg/m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 g cr sheets of best quality is laid as panel in the shutter frames.18x5mm at 0.70 kg/m ms flat is welded over the 32x6mm at 1.50kg/m ms flat on the rear side of the door, sandwitching the cr sheet for rigidity.additional stiffeners with 18x5mm at 0.7 kg/m ms flats are provided diagonally on the rear side of the shutter. 300mm length of highes 4 nos. for shutters is provided.6 nos. of hold fasts 200mm length spliced at the ends are welded to the outer frame of the door. 250mm lenght of tower bolt 2 nos., one at the top and the other at bottom are provided.250x16mm size of one aldrop is provided in case of double leaf door at lock rail section in the door. additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate placeand 2 nos. ms handles of heavy duty .ms flat 32x4mm at 1.10 kg/m is provided on the edge of the one shutter to conceal the gap between the two shutters. a tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.all members are given one coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. 52 double leaves 53 manufacturing, supplying and fixing of steel door emergency exit with the following specifications, ms angle of size 40x40x6mm at 3.5 kg/m are used for outer frames and ms angle of size 35x35x5mm at 2.6 kg/m for the shutter frames.stiffeners with ms flat 32x6mm at 1.50 kg / m is provided for fixing the aldrop for the door and welded intact 18 gauge cr sheet is laid as panel in the shutters and welded intact of 1/3 bottom portion of the shutters, 2/3 portion at top provided with ms grill at 15 kg/sq.m as per design and laid as panel in the shutters.the openable shutter also provided to cover the 2/3 grill portion with 18 gauge cr sheet with shutter frame made out of ms angle of size 35 x 35 x 5mm @ 2.60 kg / m. and stiffeners with ms flat of of size 32x6mm at 1.5 kg/m.the additional stiffeners of size 18x5mm at 0.70 kg/m is welded intact with door shutter.necessary furniture fittings also provided for this shutter as reicted by the departmental officers. necessary ‘j’ section having ms angle 46 x 25 x 3mm at 2.28 kg/m is provided in between ms grill and cr sheet bottom panel for compact fixing of the grill and sheet in position. the design and style forthe upper panel should be approved by the departmental officers. ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability. 54 ms flat 18 x 5mm at 0.7 kg/m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability.ms flat 32 x 4mm at 1.10 kg/m is provided over the edge of one shutter in case of double door, to conceal the gap between the shutters.2 nos. of 300mm length of hinges in case of single leaf door and 4 nos. of 300mm length of hinges in case of double leaf doors are provided at an appropriate place in the outer frame.6 nos. of hold fasts of 200mm in length spliced at the ends are welded to the outer frame of the door. 250mm length of tower bolts 4 nos. one at top and the other at the bottom are provided. in case of double leaf door one number aldrop is provided at an appropriate place in the doors; two numbers of 250x16mm length and 2 nos. of handle heavy duty aldrop in single leaf door.a tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing.all members are given one coat of red oxide primer as directed by the departmental officers.the rate includes cost of all materials, labour charges, taxes,transportation to site of work, loading, unloading and all other incidental charge, etc., complete. 55 double leaves 56 manufacturing, supplying and fixing in position of steel windows with the following specifications.outer frames of windows made of z section f7d of size 33 x 25 x 3 mm at 1.419 kg/m and mullion o section (f4b) of size 46 x 25 x 3 mm at 2.28 kg/m and shutter section of made of f7d of 33 x 25 x 3 mm at 1.419 kg/m as specified in is 7452/1990.each openable shutter should not exceed a width of 600 mm to enable separate operations and easy maintenance.the panel of the shutter to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. horizontal stiffeners using 18 x 5 mm ms flat at 0.70 kg/m at 3 nos for each shutters and additional diagonal stiffeners of the same ms flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the cr sheets in position firmly. 57 4 numbers of sturdy hinges and two number of handle cum latch of special type made with 18x5mm ms flats are revetted to the shutters at an appropriate height in window.suitable opening is left for its easy operation.a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle.each window shutter having an adjustable stay made out of 18x5mm at 0.70 kg/m ms flat of length 320mm with three adjustable position.a matching peg is provided in the outer frame of the window at suitable place.4 nos. of hold fasts of 120mm length spliced at the ends are welded to the out frame of the window by using ms flat of 18x5 mm at 0.70 kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter. an ms square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge to edge between them.all members are painted with one coat of anti corrosive red oxide primer as directed by the departmental officers.all sections should be in confirmed with is7452/1990. the cost includes cost of all materials, labour charges and other incidental charges, etc., complete. 58 fourleaves 59 supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of ms flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete.an additional ms flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers. 60 supplying and fixing 40mm dia gi pipe for staircase hand rail including labour charges for cutting, welding and fixing with ms flats (excluding cost of flat), etc., as directed by the departmental officers 61 supplying and fixing of m.s.grill of approved design for grill gate, grill work to doors and windows openings ramp etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification. 62 supplying and filling of 40mm iss metal in dispersion trench around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc. complete.(the rate including cost of metal filling etc., complete complying with standard specification). 63 supplying and filling of 20mm iss metal in dispersion trench around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc. complete.(the rate including cost of metal filling etc., complete complying with standard specification). 64 supplying and fixing in position best quality pvc soil / waste pipes of various dia having 6 kg / sq.cm. pressure bis mark and providing leak proof joints using pvc adhesives including fixing to the wall with special pvc / ms clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / rcc works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(the pvc pipes should be got approved by the executive engineer before use on works). the rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level 65 110mm dia pvc soil / waste pipe 66 supplying and fixing in position of the following pvc specials best approved quality conforming to iss and providing leak proof joints with pvc adhesiveetc, including fixing to walls with necessary teak wood plugs screws etc. and giving connections to the pvc pipe dismantling the brick masonry rcc floor or roof slab and redoing the disturbed portion to original conditions etc. complete complying with standard specifications. (the pvc specials should be got approved from the executive engineer before use on works). 67 110mm dia pvc elbow 68 110mm dia pvc tee 69 110mm dia pvc bend ...

Rural Development And Panchayats Department - Tamil Nadu

38920904 1 ) providing cement concrete pavement to the street from 10 th street pue school to kanagumani house at mohavanurhouse of kosavampalayam 2 ) providing cement concrete pavement to the street from thulasimani house to sellammal house at kosavampalayamhouse of kosavampalayam 3 ) construction of drainage ad colony 1 st street ohtto annachi kadai at mohavanaur house of kosavampalayam 4 ) construction of drainage ad colony gothadamaran houseto panchayat office building at mohavanaur house of kosavampalayam 5 ) construction ofpd shop at kosavampalayam house of kosavampalayam. 1 1 ) providing cc pavement to the street from 10 th street pue school to kanagumani house at mohavanurh / o kosavampalayam 2 earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per ss 20 b for foundation 3 cement concrete in 1:4:8 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 4 cement concrete in 1:3 :6 mix using 20 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 5 supplying & erecting shuttering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists ( country wood ) of size 10 x 6.5cm spaced @ about 90cm c / c and supported by casurina props of 10 13cm dia. spaced @ 75cm c / c etc., complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items. ( rcc floor slab, roof slab, rectangular / square, tee / ell beams, lintels, staircase waist slabs, landing slabs, landing beam, portico beam etc., ) . 6 cement concrete in 1:2:4 mix using 20 mm metal used for wearing coat including cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 7 2 ) providing cc pavement to the street from thulasimani house to sellammal house at kosavampalayamh / o kosavampalayam 8 earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per ss 20 b for foundation 9 cement concrete in 1:4:8 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 10 cement concrete in 1:3 :6 mix using 20 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 11 supplying & erecting shuttering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists ( country wood ) of size 10 x 6.5cm spaced @ about 90cm c / c and supported by casurina props of 10 13cm dia. spaced @ 75cm c / c etc., complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items. ( rcc floor slab, roof slab, rectangular / square, tee / ell beams, lintels, staircase waist slabs, landing slabs, landing beam, portico beam etc., ) . 12 cement concrete in 1:2:4 mix using 20 mm metal used for wearing coat including cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 13 3 ) construction of drainage ad colony 1 st street ohtto annachi kadai at mohavanaur h / o kosavampalayam 14 earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per ss 20 b for foundation 15 cement concrete in 1:4:8 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 16 cement concrete in 1:3 :6 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 17 supplying & erecting shuttering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists ( country wood ) of size 10 x 6.5cm spaced @ about 90cm c / c and supported by casurina props of 10 13cm dia. spaced @ 75cm c / c etc., complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items. ( rcc floor slab, roof slab, rectangular / square, tee / ell beams, lintels, staircase waist slabs, landing slabs, landing beam, portico beam etc., ) . 18 plastering with cement mortar 1:4 mixto 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete 19 4 ) construction of drainage ad colony gothadamaran houseto panchayat office building at mohavanaur h / o kosavampalayam 20 earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per ss 20 b for foundation 21 cement concrete in 1:4:8 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 22 cement concrete in 1:3 :6 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 23 supplying & erecting shuttering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists ( country wood ) of size 10 x 6.5cm spaced @ about 90cm c / c and supported by casurina props of 10 13cm dia. spaced @ 75cm c / c etc., complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items. ( rcc floor slab, roof slab, rectangular / square, tee / ell beams, lintels, staircase waist slabs, landing slabs, landing beam, portico beam etc., ) . 24 plastering with cement mortar 1:4 mixto 20 mm thick including cost and conveyance of all materials to site and all labour charges etc complete 25 5 ) construction ofpd shop at kosavampalayam h / o kosavampalayam 26 earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per ss 20 b for foundation 27 cement concrete in 1:4:8 mix using 40 mm metal used for foundationincluding cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete. 28 supply and filling basement with well gravel including cost and conveyance at site in all etc 29 supplying and filling in foundation, basement, etc with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 30 brick work using country bricks of size 83 / 4x41 / 4x23 / 4in cement mortar 1:5 ( one cement and fivem.sand ) including curing neat finishing, etc., complete complying with standard specifiction.1 for foundation and basement 31 2. for super structure in ground floor 32 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. 33 supplying & erecting centering for sides & soffiots including necessary supports & strutting up to 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists country wood ) of size 10 x 6.5cm spaced @ about 90cm c / c and supported by casuarinas props of 10 13cm dia. spaced @ 75cm c / c etc., complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items.1. centering below ground level 34 2. rate for column post 35 3. rate for roof slab, lintel, beam 36 4. rate for sunshade 37 cement concrete 1:1.5:3 using 20mm iss hbg metal for all rcc item of works excluding cost of rein forcemeat and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the rcc floor or roof slabs 1.for foundation and basement 38 2. for superstructure in ground floor 39 granolithic floor finish cc 1:2:4 mix using 10 12mm metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 40 weathering coarse with brick jelly lime concrete using 20mm brick jelly of 32:12.5 including cost and conveyance of all materials to site and all labourwith slacked lime in the charges for mixing , laying , and finishing etc complete for10 cumratio 41 finishing the top of roof with one course of pressed tiles conveyance of all materials to site and all labour charges etc complete for 10 sqm 42 supply of steel door of size 0.9 x 2.10m including in all other charges at site in all etc 43 supply of rolling shutters including in all other charges at site in all etc 44 supply of steel window of size 1.20 x 1.30m including in all other charges at site in all etc 45 toward the charges for fixing steel door of size 0.9 x 2.10m including in all other charges in all etc 46 toward the charges for fixing steel window of size 1.20 x 1.30m including in all other charges in all etc 47 plastering with cm 1:5, 12mm thick.over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers. 48 finishing the exposed surface of rcc item of work such as slabs, beams, sunshade, facial, canopy slab, staircase waist slab, landing slab etc., with cm 1:3, 10mm thick. including raking the surface. the rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps, landing slabs etc., complete complying with standard specifications. 49 distempering two coats with best quality of distember and the olour approved by the deparmental officer including cost and all labour charges etc., complete 50 interior / exterior emulsion two coats over priming coat including cost and conveyance of all materials and labor charges etc complete. 51 painting two coats for new steel doors , windows over the steel doors including in all charges etc complete 52 wiring with 2 x 2.5 sq.mm pvc unheated sc allocable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with pvc accesories in flush with wall, with 3mm thick hylum sheet cover with tw switch box and f.t switch and 5 a ft switch and making good of the concealed portionwith suitable colour forpvc concealed light point / fan point sd 25 53 wiring with 2 x 2.5 sq.mm pvc unheated sc allocable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non interlocking c.s. plug top with painting of suitable color for open pvc plug point. sd 41. 54 supply and fixing of single box type 4 40wflourescent tube fitting with copper choke and condenser with twround block on wall or ceiling with flourescent tube with pvc unsheathedcopper leads from terminals to the fitting oftube light [ sd88 ] 55 supply and run of 2 of 6.0 sq.mm polythene insulated pvc sheathed heavy duty sc.copper conductorof 1100 v grade on 7 / 20 gi bearer wire for service connection mains [ sd no.70 ] 56 supply and fixing of ceiling fan including cost and conveyance of all materials and labor charges etc complete. sd 110 57 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } ( refer clause 13.2 & 13.3 of section 2 of instruction to bidders ( itb ) of sbd ) ...

Rural Development And Panchayats Department - Tamil Nadu

38909331 construction of new panchayat office building at pulvaipatti panchayat of sattur block in virudhunagar district under agamt ii 2023 2024. 1 construction of new panchayat office building 2 earth work excavation for foundation in all classes of soils and sub soil to full depthexcept in hard rock requiring blasting but inclusive of shoring struttingif required forthe sides of foundation. 3 cement concrete 1:4:8 mix using 40 mm hbg metal for foundaion including watering wherever necessary and laid in layers of not more than 15cm thick. compacting etc., complete complying with standard specifications and as directed. 4 cement concrete 1:3:6 mix using 20 mm hbg metal for foundaion including watering wherever necessary and laid in layers of not more than 15cm thick. compacting etc., complete complying with standard specifications and as directed. 5 supplying and filling with filling sand in layers not more than 15 cm thick , well rammed, wattered and compacted etc, complete for foundation 6 supplying and filling with gravel in layers not more than 15 cm thick including labour charges for filling, levelling, watering, well rammed and compacted etc., complete for flooring filling material 7 brickwork in cement mortar 1:5 mix using country bricks of size 8 ¾” x 4 ¼ x 2 ¾”including cost and conveyance of all materials to site etc., complete. 8 reinforced cement concrete 1:1.5:3 mix using 20mmiss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete. 9 supplying and fabricating rts / tmt steel rods including cutting, bending hooks, cranking, fabricating, assembling and laying in exact position, typing with softsteel wire 16 gauge , etc., complete conforming to bis std. 10 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., below gl 11 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., slab & beam 12 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., column 13 weathering course with brick jelly lime concrete to 0.075m thick and finishing the top of roof with one course of pressed tiles of size 23 cm x 23 cm x 2 cm of approved quality laid in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with w 14 paving the floor with kotta green tiles of size 60cm x 60cm x 1.8 to 2 cm thick in cement mortar 1:3etc., complete complying with standard specifications and as directed by the departmental officers. 15 ceramic tiles flooring laying with new ceramic tiles of size 300x300x6 mm laid in c m 1:3 inculding cost of white cement and labour charges etc 16 dadooing the walls with new colour glazed tiles of size 300 x120 x6 mm laid in cm 1:2 , 10 mm thick and pointig with white cement using 0.40 kg / m2 including finishing the joint and pointing flush with ties surface 17 plastering in cement mortar 1:5 mix, 12mm thick including cost and conveyance of all materials to work site from the approved sources and labour charges etc., complete. 18 plastering in cement mortar 1:3 mix, 10mm thick including cost and conveyance of all materials to work site from the approved sources and labour charges etc., complete. 19 cost and supply of steel door in size of 1.10m x 2.10m with best approved quality with standard specification and as directed by the departmental officer 20 cost and supply of steel door in size of 1.00m x 2.10m with best approved quality with standard specification and as directed by the departmental officer 21 cost and supply of steel door in size of 0.75m x 1.80m with best approved quality with standard specification and as directed by the departmental officer 22 cost and supply of steel window in size of 1.20m x 1.30m with best approved quality with standard specification and as directed by the departmental officer 23 cost and supply of steel window in size of 1.50m x 1.30m with best approved quality with standard specification and as directed by the departmental officer 24 cost and supply of rolling shutter in size of 1.20m x 2.10m with best approved quality with standard specification and as directed by the departmental officer 25 cost and supply of grill gate in size of 1.20m x 2.10m with best approved quality with standard specification and as directed by the departmental officer 26 cost and supply of rcc jolly in size of 0.60m x 0.45m with best approved quality with standard specification and as directed by the departmental officer 27 distembering two coats with best approved distember including cost and conveyance of all materials to site and all labour charges etc complete 28 exterior emulsion painting two coats with best approved quality and colourpaint over one coat of base coat including cost and convyance of all materials to work site and labour charges etc., complete. 29 painting with approved quality ready mixed paint two coats including cost and conveyance of all materials to site, labour charges etc., complete for doors and windows. 30 labour charges for fixing steel doors including all charges etc., complete 31 labour charges for fixing steel windows including all charges etc., complete 32 cost and supply of indian water closet with best approved quality with standard specification and as directed by the departmental officer 33 cost and supply of european water closet with best approved quality with standard specification and as directed by the departmental officer 34 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 25 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 35 cost and supply of wash basin with best approved quality with standard specification and as directed by the departmental officer 36 25mm upvc pipe 37 cost and supply of 1000 ltr capacity hdpe tank 38 providing electrification arrangement 39 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated unsheathed sc copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with 5a ft switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for concealed pvc light / fan point ( for electronic regulator ) ( 5 points per coil ) sd 22 40 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting. sd 88 41 supply and fixing of fancy glass shade and 11w cfl for bh point sd 80 42 supply and fixing of wt bulk head fitting with guard ( philips / bajaj / crompton / k. lite ) suitable for incandescent lamp with 60 w bulb sd 83 etc., complete 43 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated unsheathed sc copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with 5a ft switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for concealed pvc light / fan point ( for electronic regulator ) ( 5 points per coil ) sd 22 44 supply and fixing of 1200 mm ( 48 ) ac ceiling fan complete with stepped electronic 300 w regulator with 300 mmdown rod on the existing clamp. sd 110 45 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated unsheathed sc copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with 5a ft switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for concealed pvc plug point sd 36 46 supply and run of 2x1.5 sq.mm ( 22 / 0.30 ) pvc insulated sc unsheathed copper conductor of 1100 v grade in 32mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 71 47 supply and run of 2 of 1.50 sq.mm ( 22 / 0.30 ) pvc insulated sc unsheathed copper conductor of1100 v grade on 7 / 20gi bearer wire for service connection mains sd 66 48 supply and fixing of 16a dp switch of 500v with matal clad with fuse and neutral ( side handle ) on suitable tw board with earth connection only sd 142 49 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1 x 1 / 8 copper flat ) on tw plank of size 375mm x 300mm x 19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd 125. 50 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38908969 tender for devathur panchayat agamt ii 2023 24 works 5nos thoppampatti block. 1 1. deepening strengthening of kodangikulam with construction of bathing ghat & baby pond at kodagipatty h / o devathurestimate amount rs.9.60lakhs 2 cleaning light jungle ( based on standardschedule of rates vid., w0002 ) 3 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete ( based on standard schedule of rates vid., w0085 ) 4 main pond 5 baby pond 6 channel area 7 civil work 8 earth work excavating and depositing on bank with an initial lead of 10m and initial lift of 2m in hard stiff clay stiff block cotton, hard red earth shales, murrams, gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil ss 20b for foundation 9 supplying and filling with sand for foundation and basement layers of not more than 15 cm thick well rammed andwatering complying with standard specification 10 cement concrete for foundation 1:4:8 using 40mm hbgs jelly including all incidental charges such as bailing out water finishing curing complete complying with standardspecification 11 providing random rubble masonry in cement mortar 1:5 mix with simultaneous pointing including cost andconveyance pf all materials to site and all labour charges etc complete 12 plastering with cement mortar 1:3 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete for 10 sqm 13 provision for name board charges 14 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 15 2. providing paver block @ tamilan nagar ad colony muneeswaran house to perumal house @ kodangipatty h / o devathurestimate amount rs.2.00 lakhs 16 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 17 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 18 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 19 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 20 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 21 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 22 provision for name board charges 23 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 24 3.construction of anganwadi near ad colony at perumalnaickenvalasu h / o devathur panchayat.estimate amount : rs.14.31 lakhs 25 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 26 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 27 filling in foundation and basement with conveyed gravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 28 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 29 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 30 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 31 rcc 1:1.5:3 mix using 20 mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 32 cement concrete 1:3:6 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 33 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 34 weathering course with best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no m.sand to be listed ) over the rcc roof slab in the proposition being brickjelly to lime 32:12:1 / 2 by volume and laid over into a single layer and cons 35 finishing the top of the roof with one course of machine pressedtiles of size 20 cm x 2 cm of approved quality laid in cement mortar 1:3 ( one cement and three m.sand ) 12 mm thick mixed with water proofing compound conforming to iss by 2% weight of cement us 36 paving the floor with plain marbonite tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 37 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 38 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 25mm thickness 39 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 40 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 41 supplying & fixing in positionof indian type baby water closet including cost and conveyace of all materials to site etc. complete. 42 iwc 43 ewc 44 supplying and fabrication of steel doord ( 1.00x2.10m ) 45 supplying and fabrication of steel doord ( 1.10x2.10m ) 46 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 47 supplying and fabrication of steel window w ( 1.2x1.3m ) 48 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 49 providing rain water pipe using 110mm pvc pipe including all labour charges etc. 50 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments with primerincluding all charges etc. 51 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 52 painting two coats for black board including all charges etc. complete 53 painting two coats over new iron work using synthetic enamel paint without primer including cost and conveyace of all materials to site etc. complete. 54 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 55 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 56 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 57 supply and fixing of 11w cfl lamp for existing bh point. ( data b ) sd 80 58 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 59 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 60 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 61 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 62 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 63 supply and fixing of main service board.etc complete. 64 provision for cartoon paintings 65 sub estimate providing pipe line arrangements 66 supply of following materials including all cost etc complete 67 63mm pvc pipe 4ksc 68 63mm pvc mta 69 63mm pvc bend 70 1000 litre hdpe tank 71 earth work excavation in all clauses of soil as per ss20b. 72 pipe line 73 provision for name board 74 supplying and fixing of rcc jolly including all charges etc. 75 construction of rain water harvesting including all charges etc. 76 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } 77 4.construction ofgirls toilet at pues at at devathur h / o devathur panchayat.estimate amount : rs.6.18 lakhs 78 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 79 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 80 random rubble masonry in cement mortar 1:5 mix with simultaneous pointing including cost and conveyance pf all materials to site and all labour charges etc complete for 10 cum 81 filling in foundation and basement with excavated earth in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 82 supplying and filling the foundation and basement with filling sand in layers not more than 15cm . thick well rammed, watered and compacted complete. 83 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 84 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 85 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 86 rcc 1:1.5:3 mix using 20 mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 87 paving the floor with scratch proof ceramic tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying etc., complete 88 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 89 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 90 providing granolithic pattern floor finish with c.c 1:2:4 mix using 10 to 12mm iss metal including cost & conveyance of all materials to site and all labour charges etc., complete. 91 supplying & fixing in positionof indian type water closets including cost and conveyace of all materials to site etc. complete. 92 iwsc 93 ewsc 94 steel door d ( 1.10x2.10m ) 95 steel door d1 ( 0.75x1.80m ) 96 rcc jolly ( 0.60x0.45m ) 97 oil bound distembering two coats using oil bound distember inclluding cost & conveyance of all materials to site and all labour charges etc., complete. 98 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 99 painting two coats over new iron work using synthetic enamel paint including cost and conveyace of all materials to site etc. complete. 100 roofing with cooland colour sheet 3 mm thk with j bolts and bitumen washer etc., 101 towards cost for manhole cover 60 x 60cm ( heavy duty ) with frame 102 electrification arrangements 103 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 17 104 supply and fixing of cfl bulb 14w including cost and conveyance of all materials and labour charges etc complete. sd 80 105 water supply arrangements 106 25mmpvc pipe 107 25mmpvc tap cork 108 40mmpvc 4 kg / sqcm pipe 109 40mm pvc coupler 110 40mm pvc elbow 111 solvent cement 112 supply and delivery of 1000 lit capacity hdpe tank 113 provision for name board charges 114 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } 115 5. construction of threshing floor at perumalnaickenvalasu h / o devathur panchayat.estimate amount rs.9.10 lakhs 116 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 117 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 118 supplying and erecting centering for sides & soffits including supports and strutting up to 3.29m height for plane surfaces in all floors with all cross bracing using mild steel sheets of size 90cm x 60cm and 10 gauge stiffened welded with mild steel angles of size 25mm x 25mm x 3mm for boarding laid over country wood poists of size 10cm x 6.5cm dia spaced at about 90cm center to center etc., complete 119 cement concrete 1:3:6 ( one cement, three sand and six hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 120 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 121 reilling the excavated earth other than sand including cost, conveyance and filling charges etc., as per standard specifications 122 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 123 cement concrete 1:2:4 ( one cement, two sand and four hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 124 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 125 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 126 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and approved colour over a priming coat including through scrapping, clean removal of dirt and including necessary plaster of pairs putty, wherever required etc complete complying with standard specification 127 resting shed roof 128 rafter 25 mm x 25 mm m.s. square tubular hollow pipe of 2.60 mm thick 129 supply and fixing of bitumen pad including cost and conveyance and all labour charges etc.complete 130 provision for name board 131 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38908939 tender for kottadurai panchayat agamt ii 2023 24 works 5nos thoppampatti block. 1 1. providing paver block pavement from ad colony west street latha house to kuppusamy house at kottadurai h / o kottadurai. ( length 62m ) estimate amount rs.2.62 lakhs 2 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 3 corwall foundation 4 levelling 5 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 6 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 7 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 8 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 9 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 10 provision for name board charges 11 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 12 2. providing paver block pavement from ad colony west street rajagopal house to saminathan house at kalthuraipudur ho kottadurai. ( length 60m ) estimate amount rs.2.92 lakhs 13 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 14 corwall foundation 15 levelling 16 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 17 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 18 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 19 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 20 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 21 provision for name board charges 22 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 23 3. providing paver block pavement east street from chitra house to school at kalthuraipudur h / o kottadurai. ( length 65m ) estimate amount rs.1.35 lakhs 24 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 25 corwall foundation 26 levelling 27 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 28 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 29 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 30 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 31 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 32 provision for name board charges 33 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 34 4.providing paver block pavement from rathinasamy shop to iyyappan house at perichipalayam h / o kottadurai. ( length 75m ) estimate amount rs.4.20 lakhs 35 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 36 corwall foundation 37 levelling 38 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 39 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 40 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 41 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 42 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 43 provision for name board charges 44 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 45 5.construction of anganwadi at perichipalayam h / o kottadurai panchayat.estimate amount : rs.14.31 lakhs 46 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 47 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 48 filling in foundation and basement with conveyed gravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 49 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 50 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 51 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 52 rcc 1:1.5:3 mix using 20 mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 53 cement concrete 1:3:6 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 54 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 55 weathering course with best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no m.sand to be listed ) over the rcc roof slab in the proposition being brickjelly to lime 32:12:1 / 2 by volume and laid over into a single layer and cons 56 finishing the top of the roof with one course of machine pressedtiles of size 20 cm x 2 cm of approved quality laid in cement mortar 1:3 ( one cement and three m.sand ) 12 mm thick mixed with water proofing compound conforming to iss by 2% weight of cement us 57 paving the floor with plain marbonite tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 58 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 59 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 25mm thickness 60 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 61 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 62 supplying & fixing in positionof indian type baby water closet including cost and conveyace of all materials to site etc. complete. 63 iwc 64 ewc 65 supplying and fabrication of steel doord ( 1.00x2.10m ) 66 supplying and fabrication of steel doord ( 1.10x2.10m ) 67 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 68 supplying and fabrication of steel window w ( 1.2x1.3m ) 69 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 70 providing rain water pipe using 110mm pvc pipe including all labour charges etc. 71 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments with primerincluding all charges etc. 72 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 73 painting two coats for black board including all charges etc. complete 74 painting two coats over new iron work using synthetic enamel paint without primer including cost and conveyace of all materials to site etc. complete. 75 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 76 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 77 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 78 supply and fixing of 11w cfl lamp for existing bh point. ( data b ) sd 80 79 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 80 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 81 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 82 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 83 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 84 supply and fixing of main service board.etc complete. 85 provision for cartoon paintings 86 sub estimate providing pipe line arrangements 87 supply of following materials including all cost etc complete 88 63mm pvc pipe 4ksc 89 63mm pvc mta 90 63mm pvc bend 91 61000 litre hdpe tank 92 earth work excavation in all clauses of soil as per ss20b. 93 pipe line 94 provision for name board 95 supplying and fixing of rcc jolly including all charges etc. 96 construction of rain water harvesting including all charges etc. 97 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } 98 6.construction of drainage with vertical soak pit from selvam house to mani house at andinaickenvalasu east street h / o kottadurai panchayat ( length 116m ) estimate amount rs.7.32 lakhs 99 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 100 up to 0.30m 101 drainage 102 cement concrete 1:4:8 ( one cement, four m.sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 103 brick work in cement mortar1:5 ( one cement and five m.sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 104 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 105 cement concrete 1:3:6 mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete 106 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. ( contractor has to make his own arrangements for the supply of steel and binding wire ) 107 reinforced cement concrete 1:1 1 / 2:3 ( one cement, one and a half crushed stone m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three m.sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 108 plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials & all labour charges etc., complete. 109 towards cost and supply offilling materialsincluding material cost and labour charges etc.complete 110 90mm metal 111 40mm metal 112 20mm metal 113 gravel 114 supply and fixing ofrcc ring900mm dia for leachpit including material cost and labour charges etc.complete 115 supplying and fixing of coverslab of 900mm dia including all charges etc., complete. 116 supply and delivery of 180m dia pvc pipeincluding material cost and labour charges etc.complete 117 supplyand fixing of rcc precast slab of 75mm thick1:2:4 using 20mm hbg jelly including all costand conveyance charges etc., complete. 118 provision for name board charges 119 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 120 7.construction of threshing floor at perichipalayam h / o kottadurai panchayat.estimate amount rs.9.10 lakhs 121 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 122 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 123 supplying and erecting centering for sides & soffits including supports and strutting up to 3.29m height for plane surfaces in all floors with all cross bracing using mild steel sheets of size 90cm x 60cm and 10 gauge stiffened welded with mild steel angles of size 25mm x 25mm x 3mm for boarding laid over country wood poists of size 10cm x 6.5cm dia spaced at about 90cm center to center etc., complete 124 cement concrete 1:3:6 ( one cement, three sand and six hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 125 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 126 reilling the excavated earth other than sand including cost, conveyance and filling charges etc., as per standard specifications 127 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 128 cement concrete 1:2:4 ( one cement, two sand and four hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 129 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 130 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 131 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and approved colour over a priming coat including through scrapping, clean removal of dirt and including necessary plaster of pairs putty, wherever required etc complete complying with standard specification 132 resting shed roof 133 rafter 25 mm x 25 mm m.s. square tubular hollow pipe of 2.60 mm thick 134 supply and fixing of bitumen pad including cost and conveyance and all labour charges etc.complete 135 provision for name board 136 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38903545 construction of anganwadi building in middle street at o.mettupatti village & panchayat of sattur blockin virudhunagar district under agamt ii 2023 2024. 1 construction of anganwadi building 2 earth work excavation for foundation in all classes of soils and sub soil to full depthexcept in hard rock requiring blasting but inclusive of shoring struttingif required forthe sides of foundation. 3 supplying and filling with gravel in layers not more than 15 cm thick including labour charges for filling, levelling, watering, well rammed and compacted etc., complete for flooring filling material 4 cement concrete 1:4:8 mix using 40 mm hbg metal for foundaion including watering wherever necessary and laid in layers of not more than 15cm thick. compacting etc., complete complying with standard specifications and as directed. 5 reinforced cement concrete 1:1.5:3 mix using 20mmiss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete. 6 brickwork in cement mortar 1:5 mix using country bricks of size 8 ¾” x 4 ¼ x 2 ¾”including cost and conveyance of all materials to site etc., complete. 7 supplying and fabricating rts / tmt steel rods including cutting, bending hooks, cranking, fabricating, assembling and laying in exact position, typing with softsteel wire 16 gauge , etc., complete conforming to bis std. 8 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., column 9 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., grade beam 10 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., plinth beam 11 supplying and erection centering for sides and soffits inculding necessary supports and structing for plain surfaces such as rcc slab, lintel, beam, column, sunshade including cost and coveyance of all materials to site and all other incidental charges etc complete., above plinth 12 providing granolethic floor finish in cement concrete 1:2:4 mix using 10 12mm iss metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete 13 paving the floor with scratch proof first quality ceramic flooring tiles laid in cement mortar 1:3 mix, 20mm thick and pointing the joints with colouring pigments including all labour and other incidental charges etc., complete design ceramic tiles 305mm x 305mm x 6mm 14 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complying with the standard specifications and as directed by the departmental officers. the glazed tiles should be got approved from the departmental officers before execution. 15 brick jelly lime concrete using 20mm brick jelly with slacked lime in the ratio of 32:12:5 including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc., complete. 16 finishing the top of roof with one course of machine pressed tiles of size 20 x 20 x 2cm of approved quality laid in cm 1:3, 12mm thick. with water proofing compound confirming to is by 2% by weight of cement used & the joint pointed neatly to full depth of tiles with the same water proofing compound mixed with cement mortar, red oxide etc., complete. 17 plastering in cement mortar 1:5 mix, 12mm thick including cost and conveyance of all materials to work site from the approved sources and labour charges etc., complete. 18 plastering in cement mortar 1:3 mix, 10mm thick including cost and conveyance of all materials to work site from the approved sources and labour charges etc., complete. 19 exterior emulsion painting two coats with best approved quality and colourpaint over one coat of base coat including cost and convyance of all materials to work site and labour charges etc., complete. 20 distembering two coats with best approved distember including cost and conveyance of all materials to site and all labour charges etc complete 21 cost and supply of steel door in size of 0.75m x 1.80m with best approved quality with standard specification and as directed by the departmental officer 22 cost and supply of steel door in size of 1.00m x 2.10m with best approved quality with standard specification and as directed by the departmental officer 23 cost and supply of steel door in size of 1.10m x 2.10m with best approved quality with standard specification and as directed by the departmental officer 24 cost and supply of steel window in size of 1.20m x 1.30m with best approved quality with standard specification and as directed by the departmental officer 25 cost and supply of jolly in size of 0.60m x 0.45m with best approved quality with standard specification and as directed by the departmental officer 26 towards the cost of providing baby friendly toilet 27 cost and supply of european water closet with best approved quality with standard specification and as directed by the departmental officer 28 cost and supply of ventilator in size of 0.90m x 0.60m with best approved quality with standard specification and as directed by the departmental officer 29 painting with approved quality ready mixed paint two coats including cost and conveyance of all materials to site, labour charges etc., complete for doors and windows. 30 labour charges for fixing steel doors including all charges etc., complete 31 labour charges for fixing steel windows including all charges etc., complete 32 supply and fixing of cudapah slab 20 30mm thick including all cost and conveyance and all labour charges etc., 33 providing electrification arrangement 34 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated unsheathed sc copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with 5a ft switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for concealed pvc light / fan point ( for electronic regulator ) ( 5 points per coil ) sd 22 35 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting. sd 88 36 supply and fixing of fancy glass shade and 11w cfl for bh point sd 80 37 supply and fixing of wt bulk head fitting with guard ( philips / bajaj / crompton / k. lite ) suitable for incandescent lamp with 60 w bulb sd 83 etc., complete 38 supply and fixing of 1200 mm ( 48 ) ac ceiling fan complete with stepped electronic 300 w regulator with 300 mmdown rod on the existing clamp. sd 110 39 supply and fixing of 3 nos. 5a ( 3 pin and 2 pin ) combined flush type wall socket with control switches concealed in suitable tw box covered with hylem sheet in flush with wall with earth connection ( for computer plug socket ) sd 139 40 supply and run of 2 of 1.50 sq.mm ( 22 / 0.30 ) pvc insulated sc unsheathed copper conductor of1100 v grade on 7 / 20gi bearer wire for service connection mains sd 64 41 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1 x 1 / 8 copper flat ) on tw plank of size 375mm x 300mm x 19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd 125. 42 supply and fixing of 16a dp switch of 500v with matal clad with fuse and neutral ( side handle ) on suitable tw board with earth connection only sd 142 43 supply and run of 2x1.50 sq.mm ( 22 / 0.30 ) pvc insulated sc unsheathed copper conductor of 1100 v grade in 25mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 44 providing water supply arrangement 45 supply and delivery of 50mm pvc pipe 10ksc 46 supply and delivery of sintex tank 47 supply and delivery of 25mm pvc rigid pipe ( 1.80mm thick ) 48 tap point ( nalli, bend, coupling including all charges ) 49 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38903506 tender for palappanpatty panchayat agamt ii 2023 24 works 5nos thoppampatti block. 1 1. deepening strengthening with baby pond in paraivalasu kulam h / o palappanpatty ( survey no.341 ) esimate amount rs.8.20 lakhs 2 cleaning light jungle ( based on standardschedule of rates vid., w0002 ) 3 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete ( based on standard schedule of rates vid., w0085 ) 4 main pond 5 baby pond 6 channel area 7 civil work 8 earth work excavating and depositing on bank with an initial lead of 10m and initial lift of 2m in hard stiff clay stiff block cotton, hard red earth shales, murrams, gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil ss 20b for foundation 9 supplying and filling with sand for foundation and basement layers of not more than 15 cm thick well rammed andwatering complying with standard specification 10 cement concrete for foundation 1:4:8 using 40mm hbgs jelly including all incidental charges such as bailing out water finishing curing complete complying with standardspecification 11 providing random rubble masonry in cement mortar 1:5 mix with simultaneous pointing including cost andconveyance pf all materials to site and all labour charges etc complete 12 plastering with cement mortar 1:3 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete for 10 sqm 13 provision for name board charges 14 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 15 2. providing paver block @ ad colony iind street from nalappan house to rajkamal house at palappanpatty h / o palappanpatty ( length 32m ) estimate amount rs.1.43 lakhs 16 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 17 corewall foundation 18 levelling 19 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 20 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 21 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 22 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 23 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 24 provision for name board charges 25 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 26 3.construction of anganwadi at palappanpatty pudur h / o palappanpatty panchayat.estimate amount : rs.14.31 lakhs 27 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 28 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 29 filling in foundation and basement with conveyed gravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 30 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 31 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 32 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 33 rcc 1:1.5:3 mix using 20 mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 34 cement concrete 1:3:6 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 35 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 36 weathering course with best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no m.sand to be listed ) over the rcc roof slab in the proposition being brickjelly to lime 32:12:1 / 2 by volume and laid over into a single layer and cons 37 finishing the top of the roof with one course of machine pressedtiles of size 20 cm x 2 cm of approved quality laid in cement mortar 1:3 ( one cement and three m.sand ) 12 mm thick mixed with water proofing compound conforming to iss by 2% weight of cement us 38 paving the floor with plain marbonite tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 39 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 40 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 25mm thickness 41 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 42 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 43 supplying & fixing in positionof indian type baby water closet including cost and conveyace of all materials to site etc. complete. 44 iwc 45 ewc 46 supplying and fabrication of steel doord ( 1.00x2.10m ) 47 supplying and fabrication of steel doord ( 1.10x2.10m ) 48 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 49 supplying and fabrication of steel window w ( 1.2x1.3m ) 50 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 51 providing rain water pipe using 110mm pvc pipe including all labour charges etc. 52 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments with primerincluding all charges etc. 53 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 54 painting two coats for black board including all charges etc. complete 55 painting two coats over new iron work using synthetic enamel paint without primer including cost and conveyace of all materials to site etc. complete. 56 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 57 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 58 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 59 supply and fixing of 11w cfl lamp for existing bh point. ( data b ) sd 80 60 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 61 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 62 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 63 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 64 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 65 supply and fixing of main service board.etc complete. 66 provision for cartoon paintings 67 sub estimate providing pipe line arrangements 68 supply of following materials including all cost etc complete 69 63mm pvc pipe 4ksc 70 63mm pvc mta 71 63mm pvc bend 72 61000 litre hdpe tank 73 earth work excavation in all clauses of soil as per ss20b. 74 pipe line 75 provision for name board 76 supplying and fixing of rcc jolly including all charges etc. 77 construction of rain water harvesting including all charges etc. 78 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } 79 4.construction of drainage with vertical soak pit @ ad colony main street from thiuman house to periyavelan house @ palappanpattypudur ho palappanpatty panchayat ( length 9.00m ) estimate amount rs.1.80 lakhs 80 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 81 up to 0.30m 82 drainage 83 cement concrete 1:4:8 ( one cement, four m.sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 84 brick work in cement mortar1:5 ( one cement and five m.sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 85 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 86 cement concrete 1:3:6 mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete 87 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. ( contractor has to make his own arrangements for the supply of steel and binding wire ) 88 reinforced cement concrete 1:1 1 / 2:3 ( one cement, one and a half crushed stone m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three m.sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 89 plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials & all labour charges etc., complete. 90 towards cost and supply offilling materialsincluding material cost and labour charges etc.complete 91 90mm metal 92 40mm metal 93 20mm metal 94 gravel 95 supply and fixing ofrcc ring900mm dia for leachpit including material cost and labour charges etc.complete 96 supplying and fixing of coverslab of 900mm dia including all charges etc., complete. 97 supply and delivery of 180m dia pvc pipeincluding material cost and labour charges etc.complete 98 supplyand fixing of rcc precast slab of 75mm thick1:2:4 using 20mm hbg jelly including all costand conveyance charges etc., complete. 99 provision for name board charges 100 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 101 5. construction of threshing floor near ad colony at palappanpattypudur h / o palappanpatty panchayat.estimate amount rs.9.10 lakhs 102 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 103 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 104 supplying and erecting centering for sides & soffits including supports and strutting up to 3.29m height for plane surfaces in all floors with all cross bracing using mild steel sheets of size 90cm x 60cm and 10 gauge stiffened welded with mild steel angles of size 25mm x 25mm x 3mm for boarding laid over country wood poists of size 10cm x 6.5cm dia spaced at about 90cm center to center etc., complete 105 cement concrete 1:3:6 ( one cement, three sand and six hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 106 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 107 reilling the excavated earth other than sand including cost, conveyance and filling charges etc., as per standard specifications 108 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 109 cement concrete 1:2:4 ( one cement, two sand and four hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 110 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 111 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 112 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and approved colour over a priming coat including through scrapping, clean removal of dirt and including necessary plaster of pairs putty, wherever required etc complete complying with standard specification 113 resting shed roof 114 rafter 25 mm x 25 mm m.s. square tubular hollow pipe of 2.60 mm thick 115 supply and fixing of bitumen pad including cost and conveyance and all labour charges etc.complete 116 provision for name board 117 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38903498 tender for 16 pudur panchayat agamt ii 2023 24 works 5 nos thoppampatti block. 1 1. deepening strengthening of nachimuthu kuttaikulam with construction of baby pond at 16puthur h / o 16puthurestimate amount rs.7.80 lakhs 2 cleaning light jungle ( based on standardschedule of rates vid., w0002 ) 3 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete ( based on standard schedule of rates vid., w0085 ) 4 main pond 5 baby pond 6 channel area 7 civil work 8 earth work excavating and depositing on bank with an initial lead of 10m and initial lift of 2m in hard stiff clay stiff block cotton, hard red earth shales, murrams, gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil ss 20b for foundation 9 supplying and filling with sand for foundation and basement layers of not more than 15 cm thick well rammed andwatering complying with standard specification 10 cement concrete for foundation 1:4:8 using 40mm hbgs jelly including all incidental charges such as bailing out water finishing curing complete complying with standardspecification 11 providing random rubble masonry in cement mortar 1:5 mix with simultaneous pointing including cost andconveyance pf all materials to site and all labour charges etc complete 12 plastering with cement mortar 1:3 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete for 10 sqm 13 provision for name board charges 14 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 15 2. providing paver block @ ad colony ist street from rangasamy house to arumugam house @ 16pudur h / o 16pudur.estimate amount rs.1.00 lakhs 16 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 17 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 18 supply and errecting centering charges for plain surface including cost & conveyance of all materials to site and all labour charges etc., complete. 19 cc 1:3:6 mix using 20mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 20 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and compacting with three wheeler 80 100 kn static roller coa pcity to acheive the desired dinsity etc., completeas technical specification clause 402 grading c. 21 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 22 provision for name board charges 23 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 24 3.construction ofanganwadi building @ 16pudur h / o 16pudur panchayat.estimate amount : rs.14.31 lakhs 25 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 26 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 27 filling in foundation and basement with conveyed gravel in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 28 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 29 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 30 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 31 rcc 1:1.5:3 mix using 20 mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 32 cement concrete 1:3:6 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 33 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 34 weathering course with best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no m.sand to be listed ) over the rcc roof slab in the proposition being brickjelly to lime 32:12:1 / 2 by volume and laid over into a single layer and cons 35 finishing the top of the roof with one course of machine pressedtiles of size 20 cm x 2 cm of approved quality laid in cement mortar 1:3 ( one cement and three m.sand ) 12 mm thick mixed with water proofing compound conforming to iss by 2% weight of cement us 36 paving the floor with plain marbonite tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 37 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 38 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 25mm thickness 39 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 40 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 41 supplying & fixing in positionof indian type baby water closet including cost and conveyace of all materials to site etc. complete. 42 iwc 43 ewc 44 supplying and fabrication of steel doord ( 1.00x2.10m ) 45 supplying and fabrication of steel doord ( 1.10x2.10m ) 46 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 47 supplying and fabrication of steel window w ( 1.2x1.3m ) 48 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 49 providing rain water pipe using 110mm pvc pipe including all labour charges etc. 50 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments with primerincluding all charges etc. 51 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 52 painting two coats for black board including all charges etc. complete 53 painting two coats over new iron work using synthetic enamel paint without primer including cost and conveyace of all materials to site etc. complete. 54 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 55 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 56 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 57 supply and fixing of 11w cfl lamp for existing bh point. ( data b ) sd 80 58 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 59 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 60 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 61 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 62 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 63 supply and fixing of main service board.etc complete. 64 provision for cartoon paintings 65 sub estimate providing pipe line arrangements 66 supply of following materials including all cost etc complete 67 63mm pvc pipe 4ksc 68 63mm pvc mta 69 63mm pvc bend 70 61000 litre hdpe tank 71 earth work excavation in all clauses of soil as per ss20b. 72 pipe line 73 provision for name board 74 supplying and fixing of rcc jolly including all charges etc. 75 construction of rain water harvesting including all charges etc. 76 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } 77 4.construction of drainage with vertical soak pit @ ad colony main street from murugayee house to karnan house @ thumbalapatty h / o 16pudur panchayatestimate amount rs.2.94 lakhs 78 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 79 up to 0.30m 80 drainage 81 cement concrete 1:4:8 ( one cement, four m.sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 82 brick work in cement mortar1:5 ( one cement and five m.sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 83 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 84 cement concrete 1:3:6 mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete 85 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. ( contractor has to make his own arrangements for the supply of steel and binding wire ) 86 reinforced cement concrete 1:1 1 / 2:3 ( one cement, one and a half crushed stone m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three m.sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 87 plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials & all labour charges etc., complete. 88 towards cost and supply offilling materialsincluding material cost and labour charges etc.complete 89 90mm metal 90 40mm metal 91 20mm metal 92 gravel 93 supply and fixing ofrcc ring900mm dia for leachpit including material cost and labour charges etc.complete 94 supplying and fixing of coverslab of 900mm dia including all charges etc., complete. 95 supply and delivery of 180m dia pvc pipeincluding material cost and labour charges etc.complete 96 supplyand fixing of rcc precast slab of 75mm thick1:2:4 using 20mm hbg jelly including all costand conveyance charges etc., complete. 97 provision for name board charges 98 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 99 5. construction of threshing floor near ad colony at 16pudur h / o 16pudur panchayat.estimate amount rs.9.10 lakhs 100 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 101 cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 102 supplying and erecting centering for sides & soffits including supports and strutting up to 3.29m height for plane surfaces in all floors with all cross bracing using mild steel sheets of size 90cm x 60cm and 10 gauge stiffened welded with mild steel angles of size 25mm x 25mm x 3mm for boarding laid over country wood poists of size 10cm x 6.5cm dia spaced at about 90cm center to center etc., complete 103 cement concrete 1:3:6 ( one cement, three sand and six hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 104 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 105 reilling the excavated earth other than sand including cost, conveyance and filling charges etc., as per standard specifications 106 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 107 cement concrete 1:2:4 ( one cement, two sand and four hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for basementincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 108 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 109 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 110 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and approved colour over a priming coat including through scrapping, clean removal of dirt and including necessary plaster of pairs putty, wherever required etc complete complying with standard specification 111 resting shed roof 112 rafter 25 mm x 25 mm m.s. square tubular hollow pipe of 2.60 mm thick 113 supply and fixing of bitumen pad including cost and conveyance and all labour charges etc.complete 114 provision for name board 115 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38902714 tender for agamt ii 2023 2024vadamadurai block tn 05 01 ( 7 works ) . 1 1. deepening and strengthening the bund and construction of new weir in notchikulam mi tank at sithuvarpatty panchayat ( est.amt rs 9.97 lakhs ) 2 clearing light jungle ( based on standard schedule of rates vid s.no 2 item no.2 ) 3 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machineryand tippers includingbenching formation of bunds breaking clods sectioning etc complete ( based on standard schedule of rates vid s.no 86 item no.1 ) 4 tank bund portion 5 add to relevant t.n.d.s, s. no.20.a, rates for new tank bunds and closing breaches for extra watering and consolidationby power roller 6 tank bund portion 7 earth work excavation deploying earth moving machinery for desilting channel having a width of upto 3 10 m and forming bund on either sides and depositing the earth on banks including jungle clearance etc complete ( item no.58 b ) 8 supply channel 9 cost of civil work 10 earthwork excavation for foundation in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders hard gravelly soil inclusive ofshoring to full depth strutting and bailing out. 11 supply and filling with the sand in 10cm thick layer inculding watering compacting cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 12 cement concrete 1:4:8 mix using 40mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete for foundation 13 cement concrete 1:3:6 mix using 20mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 14 cement concrete 1:3:6 mix using 20mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 15 supply and errection ofcentering for sides and soffits of cc works including cost and conveyance of all materials to site and all labour charges etc., complete. 16 below gl 17 above gl 18 cement concrete 1:2:4 mix using 20mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 19 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 20 part 2 : providing cc pavement at vadugapatty sc streetsakthivel house to bt roadh / o sithuvarpatty ( 44m ) .estimate amount rs.2.34 lakhs 21 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 22 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete.labour charges etc., complete. 23 supply and errection ofcentering for sides and soffits of cc works including cost and conveyance of all materials to site and all labour charges etc., complete. 24 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 25 cement concrete 1:2:4 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 26 supply and fixing of bittumen pad including all labour charges etc., complete.labour charges etc., complete. 27 supply and fixing of citizen / information board including all cost and conveyance of all materials and all labour charges etc complete 28 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 29 part 3 : providing cc pavement at vadugapatty sc streetveeraganesan house to arumugam househ / o sithuvarpatty ( 44m ) .estimate amount rs.2.34 lakhs 30 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 31 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete.labour charges etc., complete. 32 supply and errection ofcentering for sides and soffits of cc works including cost and conveyance of all materials to site and all labour charges etc., complete. 33 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 34 cement concrete 1:2:4 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 35 supply and fixing of bittumen pad including all labour charges etc., complete.labour charges etc., complete. 36 supply and fixing of citizen / information board including all cost and conveyance of all materials and all labour charges etc complete 37 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 38 part 4 : providing cc pavement at thoppupatty west streetmookkan house to ohth / o sithuvarpatty ( 43m ) .estimate amount rs.1.97 lakhs 39 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 40 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete.labour charges etc., complete. 41 supply and errection ofcentering for sides and soffits of cc works including cost and conveyance of all materials to site and all labour charges etc., complete. 42 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 43 cement concrete 1:2:4 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 44 supply and fixing of bittumen pad including all labour charges etc., complete.labour charges etc., complete. 45 supply and fixing of citizen / information board including all cost and conveyance of all materials and all labour charges etc complete 46 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 47 part 5 : construction ofpublic distribution shopbuildingat palayasithuvarpatty h / o sithuvarpatty estimate amount rs.9.77lakhs 48 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 49 supplying and filling in foundation with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 50 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 51 cement concrete 1:4:8 ( one cement, four m.sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 52 brick work in cement mortar1:5 ( one cement and five m.sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 53 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaito 54 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 55 reinforced cement concrete 1:1.5:3 ( one cement, one and a half m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessaryetc., complete complying with standard specification and as directed by the departmental officers 56 plastering with cement mortar 1:3 ( one cement and three m.sand ) , 10mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 57 plastering with cement mortar 1:5 ( one cement and five m.sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 58 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 59 paving the floor with cement based hydraulically pressed anti skid tiles ( pattern design ) 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 60 providing granolithic floor finish of the 40mm thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 61 25mm thick 62 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 63 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 64 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 65 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 66 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 67 solid pvc door shutters using 19 gauge 19mm ms square tubes for styles and outer frames. 15mm ms square tubes for top, lock and bottom rails. the steel tubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for 68 pvc door d2 of size 0.90 x 2.10m ( single leaf ) 69 supplying fabricating and fixing of alu. anodised colour matt finish half paneled and half glazed double leaf door the outer frame shall be with alu.box section 70 aluminium door of size 1.00 x 2.10 m 71 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for pds building 72 steel window w of size 1.00m x 1.30m ( double leaf ) 73 fabrication and supply of n type mild steel glazed ventilator ( in two parts ) of of the following size outer frame made of 25x25x5mm equal m.s.l angle with intermediate rails using25 x 25 x 5mmequal m.s. t section for panels with 3mm thick pin headed glass with teak wood beading and glass putty and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame, 4 nos. of hold fasts connecting the 2 parts at 75mm clear and with 45 degree inclination with 25x25mm 10g weld mesh and wire mesh including painting the whole unit with one coat of best quality of red oxide primer for pds 74 ventilator of size 0.9 x 0.6m 75 towards the cost of supply and erecting ofpull and push type steel rolling shutterwith isi make using 18 gi sheet and paintedwith one coat of best quality of red oxide primer inclusive of hood covers, transportationcharges etc. complete 76 rolling shutter 77 fabrication supply and fixing in position of aluminium natural colour matt finish fully glazed fixed partition of size 4.50x3.00m size of opening with aluminium grill including all charges etc., complete 78 aluminium partition at office 79 labour charges for fixing of doors, windowsin position including allcharges etc., complete 80 steel door 81 steel window and ventilator 82 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 83 supply and fixing of best quality approved make colour glazed earthwere wash hand basin of size 550x400mm with all accessoreis such as cast iron brackets, 32mm dia c.p.waste coupling, rubber plug and chain, 32mm dia b class g.i waste pipe, 15mm dia gm wheel valve, 15mm dia nylon connection, 15mm dia brass nipples, 15mm c.p.pillar tap andpedastal including all etc., complete 84 supply and fixing of cuddapah slab of 20 / 30mm thick for shelf arrangements including cost and conveyace of all materials to site and all labour charges etc complete 85 electrification ( 2021 22 sor ) 86 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 87 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 88 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 89 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 90 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 91 supply and fixing of cfl bulb 11w including cost and conveyance of all materials and labour charges etc complete. sd 80 92 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 93 supply and run of 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor of 1100v grade in 25mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains ( sd no: 69 ) 94 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 95 eb deposit amount 96 provision for water supply arrangements etc., 97 supply and fixing of 1000 litre hdpe tank 98 63mm dia pvc pipe 99 63mm dia pvc tee 100 63mm dia pvc elbow 101 20mm dia pvc pipe 102 20mm dia pvc tee 103 20mm dia pvc elbow 104 20mm x 15mmdia pvc reducer 105 pvc screw down tap heavy type 20mm dia 106 earth work excavation in hard stiff clay and hard rock earth and lowering and laying, jointing of pipes and refilling the trench with excavation soils, well rammed and consolidated after the pipes and specials are laid, jointed and tests including all labour charges etc., complete 107 labour charges for pvc pipe and specials fixing charges 108 provision for sanitary pipe line & dispersion arrangements including all charges etc., complete 109 110mm dia pvc pipe 4kg / sqm 110 110mm dia pvc tee 111 110mm dia pvc elbow 112 provision for front elevation with border and projections including cost and conveyance and all labour charges etc., complete 113 provision for name board and information board 114 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 115 part 6 : construction ofdrainage and cover slab with filter media at palakurichi west streeth / o sithuvarpattyest amount : 7.06 lakhs 116 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 117 foundation 118 drainage 119 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 120 supply and errection of centering and shuttering charges etc., complete. 121 cement concrete 1:2:4 mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete 122 reinforced cement concrete 1:1.5:3 ( one cement, one and a half m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessaryetc., complete complying with standard specification and as directed by the departmental officers 123 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 124 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 125 plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials & all labour charges etc., complete. 126 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 127 20mm metal 128 40mm metal 129 gravel 130 sand 131 charcoal 132 supplyand fixing ofcudappah stoneincluding all costand conveyance charges etc., complete. 133 supplying and fixing of 140mm dia pvc pipe including all charges etc., complete. 134 supplying and fixing of 63mm dia pvc pipe including all charges etc., complete. 135 towards the labour charges for filling metal , charcoal, gravel , sand etc., complete 136 providing weld mesh including cost of steel , labour charges etc., complete 137 provision for name board 138 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 139 part 7: construction of threshing floorpalayasithuvarpatty h / o sithuvarpatty estimate amount rs.9.10lakhs 140 earthwork excavation for foundation in all clauses of soils and subsoils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring, struting and bailing out water wherever neccessary and refilling the sides of foundation 141 cement concrete 1:4:8 mix using 40mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete complying with std. specifications and as directed. rate for 10 cum. 142 collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for fillingetc.complete, 143 supplying and filling in foundation, basement, etc with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 144 cement concrete 1:3:6 mix using 20mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc completefor 10 cum. 145 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 146 supply and eracting centering for sides and soffits including support and strutting up to 3.29m high for plane surface such as using mild steel sheets of size 90 x40 cm and bg for stiffened with welded mild steel angle of size 25 x 25 x3 mm for boarding laid over silver oak ( country wood ) joists of size 10 x6.50 cm spaced at about 90 centre to centre and supported by casaurina props of 10 13 cm dia spaced at 75 cm c / c etc., complete 147 cement concrete 1:2:4 mix using 20mm iss hbg metal including all cost and conveyance of all matirials and all labour charges etc complete ., 148 plastering with cement mortar 1:5 mix to 20mm thick including curing, cost and conveyance of all materials & all labour charges etc., complete. 149 supply of50 mm ms pipeincludingcost & conveyance ofall materialsetc., complete. 150 fabrication, supply and erection of steel structures as per the specification, dimensions and design requirement including all labour charges and other charges etc. complete ( including primary and secondary framing, foundation bolts, stiffener plate, cleat plate, fasteners, cold formed purlin members, ms angle, rectangular hollow sections, sag rods, bracing rods, end plate, base plate, connection plate etc using welding ) 151 supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers. 152 provision for name board charges 153 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Public Works Department - Tamil Nadu

38902206 tender for construction of 4 class room building ingovernment higher secondary school at pillayarnatham in virudhunagar district. 1 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 2 supplying and filling in foundation, basement, etc with filling stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 3 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 4 supply and filling in foundation andbasement with conveyed earth 5 kmmrin layers of not more than 15 cm thick well watered, without consolidation etc. complete complying with standard specification and as directed by the departmental officers. 5 cement concrete 1:5:10 (one cement, five crushed stone sand (m sand) and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 6 cement concrete 1:5:10 (one cement, five crushed stone sand (m sand) and ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying,consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (the rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers 7 brick workusing countrybricks of size 8 3/4 x 4 1/4 x2 3/4 in cement mortar 1:5 (one cement and five crushed stone sand) including curing neat finishing, etc., complete complying with standard specifiction. 8 a) in foundation & basement 9 brick workusing using countrybricks of size 8 3/4 x 4 1/4 x2 3/4 in cement mortar 1:6 (one cement and six crushed stone sand) including curing neat finishing, etc., complete complying with standard specifiction. 10 a) in foundation & basement 11 b) in ground floor 12 c) in first floor 13 d) in second floor 14 brick partition walls using best quality using countrybricks of size 8 3/4 x 4 1/4 x2 3/4 in cement mortar 1:3 (one cement and three crushed stone sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (hoop iron reinforcement will be measured and paid for separately) 15 a) in ground floor 16 b) in first floor 17 supplying and erecting steel strutting including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (payment for centering shall be given after the concrete is laid) 18 supplying and erecting, centering for sides and soffits including supports and strutting upto 3.29m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheet of 90cm x60cm bg 10 guage stiffened and welded with m.s. angle of 25 x 25 x 3mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10 cm to 13 cm dia spaced at 75 cm centre to centre at suitable intervals etc. complete in all floors complying with standard specification.(the payment for centeringshall be made only after the concrete is laid) 19 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 20 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 21 providing and laying in position, standardised concrete mix m 20 grade in accordance using 20mm with is:456 2000, and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg/ms and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10 12mm machine crushed stone jelly and with about (4.79 cum) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. (no separate payment will be made by the department for the excess usage of materials). 22 a) in foundation & basement 23 b) in gound floor 24 c) in first floor 25 d) in second floor 26 supplying, fabricating and placing in position m.s. or r.t.s. reinforcements grill for rcc works as per the design given including cost of steel and black binding wire etc., complete complying with standard specification. (the contractor will have to make his own arrangements for the supply of ms plain rod / rts rod and black binding wire) 27 damp proof course with cement mortar 1:4 (one cement and four p sand) 12mm thick mixed with best approved quality water proofing compound conforming to indian standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification. 28 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 29 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 (one cement and three crushed stonesand) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 30 paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un polished) in all floors laid in of cement mortor 1:3 (one cement three sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. the kota stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work, etc., complete as per standard speicification. 31 paving the floor with cement based hydrically pressed anti skid tiles (required shape and design) of 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three crushed sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.(the make and brand of the tiles should be got approved by executive engineer before use on works) 32 paving the floor with pre polished concrete anti skid step tiles (required shape and design) of 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.(the make and brand of the tiles should be got approved by executive engineer before use on works) 33 supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of ms flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete.an additional ms flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers. 34 supplying and fixing 40mm dia gi pipe for staircase hand rail including labour charges for cutting, welding and fixing with ms flats (excluding cost of flat), etc., as directed by the departmental officers 35 supplying and fixing gi pipe handrails for differently abled persons using 50mm dia gi pipe double handrail at a height of 800mm and 900mm from floor level with 25mm thick ms square rods as balusters embedded in the concrete and welded with pipe at 60cm centre to centre as shown in ca job no. 9123 / 1 including cutting, welding, bending and fixing charges and applying one coat of red oxide primer for ms members as directed by the departmental officers 36 supplying and fixing in position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 37 a) 110 mm dia 38 supplying and fixing fine polished cuddapah slab of following thickness for cup board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers. 38 / 40mm thick 39 plastering with cement mortar 1:5 (one cement and five p sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 40 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (one cement and three p sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers 41 painting two coats of newly plastered wall surface with ready mixed interior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 42 painting two coats of newly plastered wall surface with ready mixed exterior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 43 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over thered oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (the make, quality and colour of paint should be got approved by the executive engineer before use on works.) 44 supplying and fixing galvalume sheeted 0.47mm thickroofing withcement sheets of fully corrugated (grey colour) of approved quality by drilling holes (and not by punching) with necessary ‘j’ / ‘u’ bolts and nuts of 8mm dia of suitable length and providing one set of bitumen washers of 25mm dia and 1.60mm thick for each bolt including protruding portion of bolts in roof shall be covered with bitumen compound etc., complete complying with standard specification and as directedby the departmetal officers 45 providing black board in two layers with first layer in c.m. 1:5(one cement and five sand) 20mm thick and second layer in combination mortor 1:1:6 (one cement one lime and six sand) 20mm thick and 50mm width including cost of one coat blockoxide paint of approved quality etc., complete complying with standarded specification and as directed by departmental officers. 46 manufacturing supplying and fixing of steel door with the following specification ms angels of size 40x40x6mm are used for the outer frames and m.s. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm m.s flat is provided at required intervals in the shutter frame. 18 gauge c.r. sheet laid as panel in the shutter and welded intact. m.s. flat 18x5mm is welded over the 32 x 6mm m.s. flat sandwitching the c.r. sheet in between additional stiffeners with 18x5mm m.s. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. tower bolts 2nos. one at the top and the other at the bottom are provided 1no. aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door one rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place.incase of double leaf door m.s.flat 32 x 3mm at 1.1kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. a tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. all members are given a coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete. single leaf 47 manufacturing supplying and fixing of steel door with the following specification ms angels of size 40x40x6mm are used for the outer frames and m.s. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm m.s flat is provided at required intervals in the shutter frame. 18 gauge c.r. sheet laid as panel in the shutter and welded intact. m.s. flat 18x5mm is welded over the 32 x 6mm m.s. flat sandwitching the c.r. sheet in between additional stiffeners with 18x5mm m.s. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. tower bolts 2nos. one at the top and the other at the bottom are provided 1no. aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door one rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place.incase of double leaf door m.s.flat 32 x 3mm at 1.1kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. a tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. all members are given a coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.double leaf 48 fabricating, supplying and fixing of steel emergency exitdoor cum, emergency window with the following specification. m.s. angle in size 40x40x6mm are used for the outer frames and m.s. angle of sie 35x35x5mm for the shutter frame, stiffners with 32x6mm m.s. flats provided at required intervals in the shutter frames 18 guage cr sheet is laid as panel and welded instant for 1/3 bottom portion of the shutter, m.s. flat 18x5mm is welded over the 32x6mm m.s flat sandwitching the cr sheet in between additional stiffner with 18x5mm m.s. flat is provided diagonally at the rear side of the shutter. the balance 2/3 portion at top is provided with grill at an average weight of 15kg/m2 and the top portion of operation emergency window is to be made of 25x25x3mm m.s. angle welded intact with cr sheet and 25x3mm m.s. flat at diagonally at the near side of the window at required interwals 6 nos. of hinges to be provided,6 nos of holdfast 100mm in length made of angle section spliced at the ends are welded to the outer frame of the door. tower bolts 2 nos. one at top and the other at the bottom are to be provided one aldrop is provided at an appropriate place in the door 2 nos. of d typehandle for emergency window and 2 nos of handle for door is to be provided at appropriate places. a tie bar is provided at the bottom of the outer frame to prevent twisting offrame during transportation of fixing. all members are given one coat of red oxide primer as directed by the departmental officers. the rate includes cost of materials, labour transportation to side of works, loading, unloading and all other incidental charges etc., complete. double leaf 49 fabricating, supplying and fixng in position of steel windows (three leaves) with the following specifications. outer frames of windows made of z section f7d of size 33 x 25 x 3mm at 1.419 kg/ m and mullion j section (f4b) of size 46x25x3mm at 2.28kg/m and shutter section of made off7d of 33x25x3mm at 1.419 kg/m as specified in is 7452/1990. each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. the panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. horizontal stiffeners using 18x5mm ms flat at 0.70kg/m at 3 nos. for each shutter and additional diagonal stiffners of the same ms flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the cr sheets in position firmly.2 numbers of sturdy hinges and one number ofhandle cum latch of special type made with 18x5mm ms flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m ms flat of lenght 320mm with three adjustable position. a matching peg is provided in the outer frame of the window at suitable place. 4 nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using ms flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter.an ms square bar of 12mm size is welded to the inner face of the window at an equal 50 supplying and fixing mild steel iron grill for windows ventilators and grill gate etc., including one coat of red oxide primer using m.s. angle of size 40x40x6mm and grill using 20x6mm ms flat and necessary hold fast with m.s. angle of size of 40x40x6mm 230mm long spliced at end is to be provided appropriate places for fixing the grill etc complete complying with standard specification. the type design for the grills should be got approved by the departmental officers before execution. 51 providing anti termite treatment to soil adjacent under building foundation, plinth periphery of the building by application of chemicals of isi 63613 part i to iv in stages to suit the progress of work as per the detailed specification as below. including breaking of termite mounds, making holes with clow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers. stage 1: spraying anti termite chemical solution for the foundation before laying concrete in bottom and sides of foundation.stage 2: spraying anti termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth.stage 3: spraying anti termite chemical solution on the sand for the flooring before laying the flooring concrete. this treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60 cms and at 60cms intervals on both.stage 4: spraying anti termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment. 52 gst 18 % ...

Integral Coach Factory - Tamil Nadu

38887585 auction sale of description: scrap magnetic stainless steel shop refuse of various grades consisting of regular / irregular offcuts of sheets, plates, channels, pipes of all sorts, sizes and designs, punchings, remnants of punchings, window punchings of all sorts and sizes, small bits and strips of s.s magnetic variety, all rejected / obsolete fabricated magnetic stainless steel coach components generated from lhb unit, condemned / obsolete stainless steel seat, luggage and berth frames, rejected and obsolete stainless steel coach components, stainless steel window punchings, handles of all sorts, shapes, obsolete stainless steel fasteners, couplings , unusable to icf.note: ( 1 ) full sheets excluded ( 2 ) any non magnetic s.s , other ferrous, non ferrous / plastic attachments can be removed at the time of delivery. ( 3 ) larger fabricated pieces of approximately 1500 mm x 500 mm can be cut into smaller ones for loading during delivery. ( 4 ) temporary electrical connection has to be obtained from electrical department for using electical cutters. necessary hot working permit has to be obtained from safety department if gas cutting is used. gst 18 percent.other taxes as applicable.gst and any other taxes as imposed by central or state government will be to buyer?s account?location ( 1 ) bin no 15a ( 2 ) bin no 16a ( 3 ) west side of bin 16a and 15a ( 4 ) south side of ramp leading to scrap ward office and surrounding concreted area by the side of the southern boundary wall of scrap yard extending up to south side of bin no 16a, 17a quantity 50000 kg.ul no 36 9809 0719 13 14.hsn code 720421....

Rural Development And Panchayats Department - Tamil Nadu

38850702 tender for part 1 : desilting and strengthening and reconstruction of sluice at alachankulam mi tank at kulathupatti panchayat ; 2 cleaning light jungle 3 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete ( based on standard schedule of rates vid., s.no 86 item no.1 ) 4 tank bund 5 for compaction 6 channel area 7 civil work 8 earth work excavating and depositing on bank with an initial lead of 10m and initial lift of 2m in hard stiff clay stiff block cotton, hard red earth shales, murrams, gravel, stoneyearth and earth mixed with small size boulders and hard gravelly soil ss 20b for foundation 9 supply and filling of snad including cost and conveyance af all materials to site and all labour charges etc complete 10 cement concrete for foundation 1:4:8 using 40mm hbgs jelly including all incidental charges such as bailing out water finishing curing complete complying with standard specification 11 supplying, laying, jointing and fixing in position of r.c.c. hume pipes of np 3 class of 900 mm. dia with suitable collars including labour charges and jointing materials, etc., complete complying with standard specification and as directed by the departm 12 supplying and fixing cut stone roughly dressed to size all faces and set in cement mortar 1:3 ( one cement and three sand ) including all incidental charges such as finishing and curing etc., complete complying with standard specification 13 supply and erection of centering and shuttering including all cost and all charges etc complete 14 cement concrete for foundation 1:3:6 using 20mm hbgs jelly including cost and conveyance pf all materials to site and all labour charges etc complete 15 fabricating andsupply of country woodplug size of 40 * 40 cm and 45 cm to 60 cm height. the plug rod with 20 mm dia mild steel rod size of 3.0m to 4.50 m height, the plugtop side, middle, centre and bottom side covered iron strap 3 nos. plate th 16 provision for name board charges 17 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 18 part 2 : construction of agricultural godown at rengagoundanpudhur in kulathupatty panchayatestimate amount rs.13.50 lakhs 19 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 20 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 21 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 22 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 23 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 24 below gl 25 above gl 26 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 27 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 28 below gl 29 above gl 30 plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 31 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 32 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 33 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 34 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 35 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 36 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 37 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 38 towards supply and delivery and fixing of rolling shutter 39 rs ( 1.80*2.10 ) 40 towards supply and delivery of new steel window as per std. specification 41 steel window w of size 1.20m x 1.30m ( double leaf ) 42 electrification 43 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 44 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 45 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 46 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 47 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 48 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 49 provision forname board 50 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38835973 construction of community hall building in ambedhkar nagar in thiruchitrambalam village and panchayat in tenkasi panchayat union in tenkasi district under nnt fund 2023 24 construction of community hall building in ambedhkar nagar in thiruchitrambalam village and panchayat in tenkasi panchayat union in tenkasi district under nnt fund 2023 24 , 1.construction of community hall building in ambedhkar nagar in thiruchitrambalamvillage andpanchayat in tenkasipanchayatunion. , earth work excavation in hard stiff clay soil with initial lead and lift as per ss 20b for corewall etc., complete. , cement concrete 1:4:8 mix using 40mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing,laying and curing etc completefor 10 cum. , brick work in cement mortar 1:5 mix using country bricks 83/4x4 1/4x2 3/4 and conveyance of all materials to site and all labour charges etc complete for 10cum , supplying and fabrication of steel including cost and conveyance of bending to shape and tying in position and forming grills for all r.c.c works including cost and conveyance of all materials to site , reinforced cement concrete 1:1.5:3 mix using 20mmiss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum. , providing steel centering & shuttering charges for rcc &plain surface cost of country wood plank including all cost & conveyance and all labour charges etc complete above basement , below basement , above basement , refilling the basement with excavated earth including all labour charges such as watering and ramming etc complete. , supplying and filling of conveyed earth by lorry in basement filling including stacking for premeasurement, conveyance loading, and unloading charges and all other incidential charges and including filling laying watering and consolidating etc., complete , supplying and fixing ofsteeldoor size 0.90 mx2.10m including cost and conveyance of all materials to site and all labour charges etc complete. , supplying and fixing ofsteeldoor size 1.80 mx2.10m including cost and conveyance of all materials to site and all labour charges etc complete. , supplying and fixing of pvcdoor size 0.75 mx2.10m including cost and conveyance of all materials to site and all labour charges etc complete. , supplying and fixingwindowof size 1.20x1.30 including cost and conveyance of all materials to site and all labour charges etc complete. , supplying and fixingwindowof size 1.50x1.30 including cost and conveyance of all materials to site and all labour charges etc complete. , supplying and fixing of steel ventilatorsof size 0.90x0.45mincluding cost and conveyance of all materials to site and all labour charges etc complete. , labour charges for fixing of steel door includingcost and conveyance of all materials to site and all labour charges etc complete. , labour charges for fixing of steel window,ventilators includingcost and conveyance of all materials to site and all labour charges etc complete. , plastering with cement mortar 1:3 mixto 10 mm thick including cost and conveyance of all materials to site and all labour charges etc complete for 10 sqm. , plastering with cement mortar 1:5 mixto 12 mm thick including cost and conveyance of all materials to site and all labour charges etc complete for 10 sqm. , providing granolethic floor finish in cement concrete 1:2:4 mix using 10 12mm iss metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete for 10 cum. , brick jelly lime concrete using 20mm brick jelly with slacked lime in the ratio of 32:12.5 including cost andconveyance of all materials to site and all labour charges for mixing , laying ,and finishing etc complete for10 cum , finishing the top of roof with one course of pressed tiles of size 23 cm x 23 cm x 2 cm laid in cement mortar 1:3 (one cement and three sand) 12mm thick mixed with water proofing compound conforming to i.s. at 2% by weight. , white wasting two coat using shalline distembering two coats with best approved distemberincluding cost and conveyance of all materials to site and all labour charges etc complete , color wasting two coat using cobt exterior emulsion painting two coats with best approved quality and colourpaint over one coat of base coat including cost and convyance of all materials to work site and labour charges etc., complete. , painting two coats over new iron works using ready mixed enamel paint including cost and conveyance of paint and all labour charges etc complete , supplying and fixing in position best quality pvc rain water pipe having isi mark and providing leak proof joints including fixing to the wall with special pvc/ms clamps etc. , gst amount for providing service to government contract works for the above renewalworks. { gst amount is the total gst amount for overall quoted amountabove this row in column bb for all works in this package} (refer clause 13.2 & 13.3 of section 2 of instruction to bidders (itb) of sbd)...

Rural Development And Panchayats Department - Tamil Nadu

38816220 tender for shanarpatty block of6 works snpt 11 4. 1 part 1:desilting and strengthing ofbund kalathupatty kalkuthu oorani with baby pond at kalathupatty h / o madur estimate amount :9.85 / lakhs 2 clearing the scrubed jungle without uprooting and disposing of the same as directed by the engineer in charge of the works and as per technical specification 3 earth work in all soils except hard rock requiring blasting and conveying by earth by deploying earth moving machineries and tippers etc complete fomation of bund in layer of suitable thickness benching of slopes prior to placement od earth fill breaking clods watering to omc ( optimum moidture content ) and compaction of each layer to 95% proctor density through deployment of appropriate compaction eqipement ( + 8 10t power roller / vibtratory power roller / short width + 0.90m with drum ) power roller or vibratory power roller / fuel oparated or elect oparated plade compactor ensuring compaction of dedigned bund section including side slopes complete as per specification. 4 main pond 5 baby pond 6 channel area 7 bathing ghad 8 earth work excavating and depositing on bank with an initial lead of 10m and initial lift of 2m in hard stiff clay stiff block cotton, hard red earth shales, murrams, gravel, stoneyearth and earth mixed with small size boulders and hard gravelly soil ss 20b for foundation 9 supplying and filling with sand for foundation and basement layers of not more than 15 cm thick well rammed and watering complying with standard specification 10 cement concrete 1:4:8 mix using 40mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 11 supplying and erecting centeringshuttering includingnecessary supportsfor plane surface infoundationandbasementandinallfloorsfor pcc column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, criticalpier etc 12 cement concrete for superstructure 1:3:6 using 40mm hbgs jelly including all incidental charges such as bailing out water finishing curing complete complying with standard specification 13 cement concrete 1:2:4 mix using 20mm iss metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete 14 provision for name board charges 15 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 16 part 2 : providing paver block pavement with two side drainage at pugaielaipatty from mariya arockiyam teacher house to yagappan house ( 120m ) estimate amount :9.73 / lakhs 17 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss 20b ( for drain ) 18 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 19 supplying and erecting centeringshuttering includingnecessary supportsforplane surface includng all labour charges etc., complete 20 pcc 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 21 constrution of granular sub base by providing with graded materials of size 25 mm to 4.75mm metal in 65% 4.74 mm to 2.36 mm metal in 20%& 2.36mm in 15% includingspreading in uniform layaerswith motor grade on propared surface , mixing by mix in place method with rotavator at omc and compacting with three wheler 80 100 kn static roller capacity to acheive the desired density etc.. complete as technical specification clause 402 grading c ( out put 300cum ) 22 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 23 plastering in c:m 1:5 mix to 20mm thick including cost and conveyance of all matials to site and all labour charges etc., complete. 24 provision for name board charges 25 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 26 part 3 : providing paver block pavement with drainage at madurpalani house to drama stage estimate amount :4.00 / lakhs 27 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b ( for core wall ) 28 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 29 supplying and erecting centeringshuttering includingnecessary supportsforplane surface includng all labour charges etc., complete 30 pcc 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 31 constrution of granular sub base by providing with graded materials of size 25 mm to 4.75mm metal in 65% 4.74 mm to 2.36 mm metal in 20%& 2.36mm in 15% includingspreading in uniform layaerswith motor grade on propared surface , mixing by mix in place method with rotavator at omc and compacting with three wheler 80 100 kn static roller capacity to acheive the desired density etc.. complete as technical specification clause 402 grading c ( out put 300cum ) 32 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 33 plastering in c:m 1:5 mix to 20 mm thick including cost and conveyance of all matials to site and all labour charges etc., complete 34 provision for name board arrangements etc., complete. 35 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 36 part 4 :constrcution of girls toilet at m.maniyakaranpatty puesestimate amount :6.18 / lakhs 37 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 38 cement concrete 1:4:8 ( one cement, four m.sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 39 r.r. masonry in c.m.1:5 mix for foundation and basement using rough stones and bond stones with simultaneous pointing with same mortar including cost and conveyance of all materials to site and all labour charges etc., complete. 40 brick work in cement mortar1:5 ( one cement and five m.sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 41 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 42 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 43 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 44 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 45 reinforced cement concrete 1:1.5:3 ( one cement, one and a half m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessaryetc., complete complying with standard specification and as directed by the departmental officers 46 plastering with cement mortar 1:3 ( one cement and three m.sand ) , 10mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 47 plastering with cement mortar 1:5 ( one cement and five m.sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 48 plastering with cement mortar 1:3 ( one cement and three m.sand ) , 20mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 49 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 50 paving the floor with cement based hydraulically pressed anti skid tiles ( pattern design ) 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 51 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 52 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 53 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 54 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 55 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 56 fabrication and supply & delivery of mild steel doors of the following sizewith double leaf outer frame made of 35x35x5 mm equal m.s.l angle and shutter frame made of 25x25x5mm equal m.s l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 nos horizontal, 3 nos. diagonal for each shutter using ms flat of size 20x5mm fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos. of hold fasts made of 35x35x5 mm equal m.s l angle, 2 nos. of wind appliances, 3 nos. of tower bolts, 1 no aldrop, 3 nos. of handles fixing the shutter with 6 nos. of 6 inchhinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for anganwadi building. 57 steel door d of size 0.75 x 1.80m ( single leaf ) 58 steel door d1 of size 1.00 x 1.80m ( single leaf ) 59 supply and fixing of rcc jally of size 0.90 x 0.45m including cost and conveyace of all materials to site and all labour charges etc complete 60 rcc jally of size 0.60 x 0.45m 61 labour charges for fixing of doors, windowsin position including allcharges etc., complete 62 supplying and fixing in position by means of 75mm long and 6.5mm dia counter sunk bolts and nuts embedded in the floor with rubber or fibre washers.best quality and approved make white glazed earthern ware european water closet with p or s trap with seat and double flapped rigid pvc seat cover with chromium plated hinges, and giving necessary connection to pvc socket using 110 mm dia pvc pipe 6 kg / sqcm.of 0.60m length including supplying and fixing pvc tank of 10.00 litre capacity with all internal fittings witha pair of cast iron brackets and with all fittings such as 15mm dia nylon connection, 15mm dia gm wheel value, 15mm dia brass nipple including, labour charges for fixing the flushing tank on wall with teak wood plugs and screws, giving water supply connection, painting ci brackets with two coats of best approved quality synthetic enamel paint over a coat of red oxide primer, redoing the disturbed masonry and flooring to original condition, etc. complete complying with standard specification. 63 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 ( one lime two sand and five brick jelly ) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg / sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 64 supply and fixing of best quality approved make colour glazed earthwere wash hand basin of size 550x400mm with all accessoreis such as cast iron brackets, 32mm dia c.p.waste coupling, rubber plug and chain, 32mm dia b class g.i waste pipe, 15mm dia gm wheel valve, 15mm dia nylon connection, 15mm dia brass nipples, 15mm c.p.pillar tap andpedastal including all etc., complete 65 provision for water supply arrangements etc., 66 supply and fixing of 500 litre hdpe tank 67 32mm dia pvc pipe 10ksc 68 32mm dia pvc coupler 69 32mm dia pvc elbow 70 32mm dia pvc tee 71 32mm dia pvc ball valve 72 20mm dia pvc screw down tap heavy type 73 earth work excavation in hard stiff clay and hard rock earth and lowering and laying, jointing of pipes and refilling the trench with excavation soils, well rammed and consolidated after the pipes and specials are laid, jointed and tests including all labour charges etc., complete 74 provision for sanitary pipe line & dispersion arrangements including all charges etc., complete 75 110mm dia pvc pipe 4kg / sqm 76 110mm dia pvc tee 77 110mm dia pvc elbow 78 supplying and fixing ac ventilating shaft of 100mm dia with 3 metre height including cost of 100mm dia ac cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers 79 supplying and fixing in position ci manhole covers with ci frames ( heavy duty ) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications 80 soak pits 81 manufacturing, supplying of 900mm dia precast reinforced cement concrete ring of 12mm thickness with 300mm hieght in rcc 1:1.5:3, using 10 12mm hbgs jelly including cost of reinforcement steel in position and cost of moulding charges, casting of ring, finishing, curingetc., complete complying with standard specification and as directed by the departmental officers 82 manufacturing, supplying of 900mm dia precast reinforced cement concrete slab of 250mm thickness in rcc 1:1.5:3, using 10 12mm hbgs jelly including cost of reinforcement steel in position and cost of moulding charges, casting of ring, finishing, curingetc., complete complying with standard specification and as directed by the departmental officers 83 fifre roofing for toilets 84 supplying and fixing of hollow ms rectangle and square for light roofing for urinal including cost and conveyance of ms hollow pipe and labour charges for cutting and welding and placing in position including all labour charges etc., complete 85 supplying and fixing colour coated galvanised sheet for roofing including all labour charges for fixing neccesary bolt, nuts, screws, j or u bolts etc including cost and conveyance etc., complete 86 towarfs the cost for providing hand rail for ramp including cost and conveyance and all labour charges etc., complete 87 provision for name board arrangements etc., complete. 88 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 89 part 5 :construction of drainage with herizontal fillter media at kannimanagar ad colony from manikam house to kumar house estimate amount :7.80 / lakhs 90 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss 20b 91 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 92 supplying and erecting centeringshuttering includingnecessary supportsforplane surface includng all labour charges etc., complete 93 pcc 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 94 supplying and filling of 40mm metal including all cost, conveyance and all labour charges etc., complete. 95 supplying and filling of 20mm metal including all cost, conveyance and all labour charges etc., complete. 96 supplying and filling of sand including all cost, conveyance and all labour charges etc., complete. 97 plastering in c:m 1:5 mix to 20mm thick including all cost, conveyance and all labour charges etc., complete. 98 exterior emulsion painting two coats with best approved quality emulsion over one coat of base coat including all cost, conveyance and all labour charges etc., complete. 99 towards the cost, supply of 63 mm pvc pipe including cutting and fixing labour charges etc., complete. 100 supply of 63mm dia pipe, cutting and fixing all labour charges etc., complete. 101 provision for kalvazhai plantation including cost, conveyance and fixing the plant labour charges etc., complete. 102 provision for name board arrangements etc., complete. 103 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 104 part 6:construction of agricultural godown at m.mettupatty h / o madurestimate amount :6.70 / lakhs 105 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 106 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 107 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 108 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 109 supplying and filling in basement with gravel with an average lead of 1km inculding cost of gravel and conveyance charges and all other labour charges etc.complete 110 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 111 below gl 112 above gl 113 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 114 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 115 below gl 116 above gl 117 plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 118 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 119 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 120 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 121 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 122 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 123 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 124 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 125 towards supply and delivery and fixing of rolling shutter 126 rs ( 1.80*2.10 ) 127 towards supply and delivery of new steel window as per std. specification 128 steel window w of size 1.20m x 1.30m ( double leaf ) 129 supply and fixing of ventilator 0.90x0.45 130 labour charges for fixing of windowsin position including allcharges etc., complete 131 electrification 132 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 17 133 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 134 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 135 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 136 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 137 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 138 provision for name board arrangements etc., complete. 139 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 140 provision for name board...

Rural Development And Panchayats Department - Tamil Nadu

38815996 tender for vedasandur block dindigul district of 2 works tn 05 14 agamt 09. 1 part 1 : construction of pd shop at samymuthanpatty in marambady panchayatestimate amount rs.9.77 lakhs 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation with filling m.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 5 cement concrete 1:4:8 (one cement, four m.sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 6 brick work in cement mortar1:5 (one cement and five m.sand) using best quality of country bricks of size 8 3/4 x 4 1/4 x 2 1/4for foundation and basement including curing, etc., complete complying with standard specifiction. 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 8 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 9 reinforced cement concrete 1:1.5:3 (one cement, one and a half m.sand and three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessaryetc., complete complying with standard specification and as directed by the departmental officers 10 plastering with cement mortar 1:3 (one cement and three m.sand), 10mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 11 plastering with cement mortar 1:5 (one cement and five m.sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 12 dadooing wall with glazed tiles of any colour of any size laid in c.m 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete 13 paving the floor with cement based hydraulically pressed anti skid tiles(pattern design) 20mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. 14 providing granolithic floor finish of the 40mm thickness with plain cement concrete 1:2:4 (one cement, two sand and four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 15 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 (one cement and three sand) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 16 white washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers. 17 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 18 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 19 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 20 solid pvc door shutters using 19 gauge 19mm ms square tubes for styles and outer frames. 15mm ms square tubes for top, lock and bottom rails. the steel tubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. the over all size of styles shall be 50mm x 30mm. the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. the over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter 21 pvc door d2 of size 0.90 x 2.10m (single leaf) 22 aluminium door of size 1.00 x 2.10m 23 fabrication and supply of mild steel window of of the following size with double leaves outer frame made of 35x35x5 mm equal m.s.l angle, mullion section made of 25x25x5mm equal t section, shutter frame madeof 25 x 25 x 5mmequal m.s.l angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2 no. horizontal for each shutter using 25 x 25 x 5mmequal m.s. t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame,4 nos. of hold fasts made of 35x35x5 mm equal m.s.l angle , 2 nos. of peg stays with holes for keeping the windows open in different positions, 2 nos. of locking handles, fixing the shutter with 4 nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for pds building 24 steel window w of size 1.00m x 1.30m (double leaf) 25 fabrication and supply of n type mild steel glazed ventilator (in two parts)of of the following size outer frame made of 25x25x5mm equal m.s.l angle with intermediate rails using25 x 25 x 5mmequal m.s. t section for panels with 3mm thick pin headed glass with teak wood beading and glass putty and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame,4 nos. of hold fasts connecting the 2 parts at 75mm clear and with 45 degree inclination with 25x25mm 10g weld mesh and wire mesh including painting the whole unit with one coat of best quality of red oxide primer for pds 26 ventilator of size 0.90m x 0.60m 27 towards the cost of supply and erecting ofpull and push type steel rolling shutterwith isi make using 18 gi sheet and paintedwith one coat of best quality of red oxide primer inclusive of hood covers, transportationcharges etc. complete 28 rolling shutter 29 fabrication supply and fixing in position of aluminium natural colour matt finish fully glazed fixed partition of size 4.50x3.00m size of opening with aluminium grill including all charges etc.,complete 30 aluminium partition at office 31 labour charges for fixing of doors, windowsin position including allcharges etc.,complete 32 steel doors 33 steel window and ventilator 34 supplyand fixing in position best approved quality and make white glazed earthen ware oriya type indian water closet of size 580 mm with p or s trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 (one lime two sand and five brick jelly) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the pvc soil stacks using 0.60 mlong pvc pipe 110 mm dia. 6 kg/sqcm by dismantling masonry, rcc roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications 35 supply and fixing of best quality approved make colour glazed earthwere wash hand basin of size 550x400mm with all accessoreis such as cast iron brackets, 32mm dia c.p.waste coupling, rubber plug and chain, 32mm dia b class g.i waste pipe, 15mm dia gm wheel valve, 15mm dia nylon connection, 15mm dia brass nipples, 15mm c.p.pillar tap andpedastal including all etc.,complete 36 supply and fixing of cuddapah slab of 20/30mm thick for shelf arrangements including cost and conveyace of all materials to site and all labour charges etc complete 37 electrification 38 wiring with 2 x 1.5 sq.m (22/0.3) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point/fan point(for electronic regulator) s.d.no: 17 39 wiring with 2 x 1.5 sq.m (22/0.3) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 40 supply and fixing of 1200mm (48) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 41 supply and run of 2 of 1.50 sq.mm (22/0.3) pvc insulated sc unsheathed cu.conductor of 1100 v on 7/20 gi bearer wire for service connection mains. s.d.no: 64 42 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 43 supply and fixing of cfl bulb 11w including cost and conveyance of all materials and labour charges etc complete. sd 80 44 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral (side handle) on suitable tw board, with earth connection only. s.d.no: 142 45 supply and run of 2 x 1.5 sq.mm. (22 / 0.3) pvc insulated single core unsheathed copper conductor of 1100v grade in 25mm dia gi pipe (class b) suitably bent at both ends with necessary angle iron upright and end supports for mains (sd no: 69) 46 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit(500v) 32a neutral link and earth link (1x1/8 copper flat) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7/20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 47 eb deposit amount 48 provision for water supply arrangements etc., 49 supply and fixing of 1000 litre hdpe tank 50 63mm dia pvc pipe 51 63mm dia pvc tee 52 63mm dia pvc elbow 53 20mm dia pvc pipe 54 20mm dia pvc tee 55 20mm dia pvc elbow 56 20mm x 15mmdia pvc reducer 57 pvc screw down tap heavy type 20mm dia 58 earth work excavation in hard stiff clay and hard rock earth and lowering and laying, jointing of pipes and refilling the trench with excavation soils, well rammed and consolidated after the pipes and specials are laid, jointed and tests including all labour charges etc.,complete 59 labour charges for pvc pipe and specials fixing charges 60 provision for sanitary pipe line & dispersion arrangements including all charges etc.,complete 61 110mm dia pvc pipe 4kg/sqm 62 110mm dia pvc tee 63 110mm dia pvc elbow 64 provision for front elevation with border and projections including cost and conveyance and all labour charges etc.,complete 65 provision for name board 66 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package} 67 part 2 : construction of agricultural godown at muthupalaniyur in usilampatty panchayatestimate amount rs.9.10 lakhs 68 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 69 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 70 cement concrete 1:4:8 (one cement, four sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 71 brick work in cement mortar1:5 (one cement and five sand) using best quality of country bricks of size 8 3/4 x 4 1/4 x 2 1/4for foundation and basement including curing, etc., complete complying with standard specifiction. 72 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 73 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 74 below gl 75 above gl 76 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 77 reinforced cement concrete 1:1.5:3 (one cement, one and a half sand and three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 (one cement and three sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 78 below gl 79 above gl 80 plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 81 plastering with cement mortar 1:5 (one cement and five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 82 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (one cement, two sand and four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 83 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 84 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 (one cement and three sand) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 85 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 86 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 87 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 88 towards supply and delivery and fixing of rolling shutter 89 rs (1.80*2.10) 90 towards supply and delivery of new steel window as per std. specification 91 steel window w of size 1.20m x 1.30m (double leaf) 92 labour charges for fixing of windowsin position including allcharges etc.,complete 93 electrification 94 wiring with 2 x 1.5 sq.m (22/0.3) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point/fan point(for electronic regulator) s.d.no: 20 95 wiring with 2 x 1.5 sq.m (22/0.3) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 96 supply and fixing of 1200mm (48) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 97 supply and run of 2 of 1.50 sq.mm (22/0.3) pvc insulated sc unsheathed cu.conductor of 1100 v on 7/20 gi bearer wire for service connection mains. s.d.no: 64 98 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 99 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral (side handle) on suitable tw board, with earth connection only. s.d.no: 142 100 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit(500v) 32a neutral link and earth link (1x1/8 copper flat) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7/20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 101 providing rain water downfall pipe 102 provision forname board 103 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package} ...

Rural Development And Panchayats Department - Tamil Nadu

38813348 tender for vedasandur block dindigul district of 4 works. 1 part 1 : providing paver block pavement at navamarathupatty ad colony east street thirumathal house to vennila house in usilampatty panchayatestimate amount rs.3.08 lakhs 2 earthwork excavation and depositing on bank with an initial lead and lift in all classes of soils and sub soils except in hard rock including all labour charges etc . complete. 3 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 4 supply & erection of centering for sides & soffits of all r.c.c. worksincluding cost & conveyance of all materials to site and all labour charges etc., complete. 5 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 6 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and 7 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of spec 8 provision for name board 9 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 10 part 2 : providing paver block pavement at usilampatty old ad colony wast street community hall to murugayee house in usilampatty panchayatestimate amount rs.1.80 lakhs 11 earthwork excavation and depositing on bank with an initial lead and lift in all classes of soils and sub soils except in hard rock including all labour charges etc . complete. 12 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 13 supply & erection of centering for sides & soffits of all r.c.c. worksincluding cost & conveyance of all materials to site and all labour charges etc., complete. 14 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 15 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and 16 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of spec 17 provision for name board 18 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 19 part 3 : providing paver block pavement at navamarathupatty ad colony north street andiyammal house to dhanalakshmi house in usilampatty panchayatestimate amount rs.3.60 lakhs 20 earthwork excavation and depositing on bank with an initial lead and lift in all classes of soils and sub soils except in hard rock including all labour charges etc . complete. 21 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 22 supply & erection of centering for sides & soffits of all r.c.c. worksincluding cost & conveyance of all materials to site and all labour charges etc., complete. 23 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 24 construction of granular sub base by providing with graded materials of size 9.5mm to 4.75mm metal in 66% & 2.36mm in 34% including spreading in uniform layers with motor grader on propared surface, mixing by mix in place method with rotavator at omc and 25 providing and laying of interlocking concrete block ( surface textured ) pavements having thickness 60mm and compacted over a thin bedding sand layer of 30 mm thickness and joints shall be filled by fine sand of specified grading as per table 1500.6 of spec 26 provision for name board 27 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 28 part 4 : construction of agricultural godown at muthupalaniyur in usilampatty panchayatestimate amount rs.9.10 lakhs 29 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 30 supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 31 cement concrete 1:4:8 ( one cement, four sand and ten hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 32 brick work in cement mortar1:5 ( one cement and five sand ) using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 1 / 4for foundation and basement including curing, etc., complete complying with standard specifiction. 33 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 34 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton 35 below gl 36 above gl 37 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. 38 reinforced cement concrete 1:1.5:3 ( one cement, one and a half sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 39 below gl 40 above gl 41 plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete. 42 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 43 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 44 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 45 finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 46 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. 47 painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 48 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. 49 towards supply and delivery and fixing of rolling shutter 50 rs ( 1.80*2.10 ) 51 towards supply and delivery of new steel window as per std. specification 52 steel window w of size 1.20m x 1.30m ( double leaf ) 53 labour charges for fixing of windowsin position including allcharges etc., complete 54 electrification 55 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) s.d.no: 20 56 wiring with 2 x 1.5 sq.m ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessoriesand with 150 x 100 x 113 tw switch box for 5a 3pin non inter locking cs plug with painting of suitable colour with continuos earth wire connection of 14 swg tc wire for open pvc plug s.d.no: 36 57 supply and fixing of 1200mm ( 48 ) ac ceiling fan with stepped electronic 300 w regulator with 1 meter down rod on the existing clamp. s.d.no: 107 58 supply and run of 2 of 1.50 sq.mm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100 v on 7 / 20 gi bearer wire for service connection mains. s.d.no: 64 59 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 60 supply and fixing of 16 amps dpic switch of 500v with fuse and neutral ( side handle ) on suitable tw board, with earth connection only. s.d.no: 142 61 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1x1 / 8 copper flat ) on tw plank of size 375mmx300mmx19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit sd no: 125 62 provision forname board 63 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38742782 construction of cremation shed and 2 nos works under agamt fund 2023 24 nilakkottai block tn 05 01. 1 1. providing providing paver block with drainagefrom anna nagarrajathiamman kovil to soman houseat ramarajapuramh / o ramarajapuram 160m est rs 9.90 lakhs 2 earth work excavation for foundation in all soils and sub soils to full depth etc., ordinary soil complete 3 earth work excavation for foundation in all soils and sub soils to full depth etc., ordinary soil complete for drain 4 cement concrete 1:4:8 ( one cement, four m.sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification 5 plain cement concrete 1:3:6 ( one cement, twom.sand and four hard broken stone jelly ) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.for core wall 6 plain cement concrete 1:3:6 ( one cement, twom.sand and four hard broken stone jelly ) using 40mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. for drain 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. ( payment for centering shall be given after the concrete is laid ) 8 construction of granular sub base by providing well graded material ( 25 mm to 4.75 mm irc hbg metal @ 65 %, 4.75 to 2.36mm irc hbg metal@20%&2.36 mm below irc hbg metal @15% ) & ( the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 25 & 6% repectively ) spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with rotovator at omc and compacting with three wheel 80 100 kn capacity and finished in accordance with the requirements of the specification and thickness as per approved plans or as directed by the engineer ( mix in place method ) . 9 providing and laying of interlocking concrete ( surface textured ) block pavements having thickness 60mm and compacted over a thin bedding m.sand layer of 25 mm thickness and joints shall be filled by fine m.sand of specified grading as per table 1500.6 of specification of rural roads 2014 andtechnical specification clause 1504. 10 plastering with cement mortar 1:5 ( one cement and five m.sand ) , 20 mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 11 provision for name board 12 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 13 2.construction ofanganwadi building in south street at ramarajapuramh / o ramarajapurampanchayatest rs 14.31lakhs 14 earth work excavation for foundation in all soils and sub soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation. 15 cement concrete 1:4:8 ( one cement, four m.sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification 16 filling in foundation and basement with conveyed in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 17 brick work using country bricks of size 83 / 4x41 / 4x23 / 4in cement mortar 1:5 ( one cement and fivem.sand ) including curing neat finishing, etc., complete complying with standard specifiction. 18 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. ( payment for centering shall be given after the concrete is laid ) 19 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. ( contractor has to make his own arrangements for the supply of steel and binding wire ) 20 r. cement concrete 1:1 1 / 2:3 ( one cement, one and a half crushed stone m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three m.sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 21 plain cement concrete 1:2:4 ( one cement, twom.sand and four hard broken stone jelly ) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. 22 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no crushed stone m.sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 23 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three crushed stonem.sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 24 paving the floor with best quality vertified tiles of size 600 x 600 x 8mmof approved colour, shade and quality laid in cement mortar 1:3 ( one cement and three crushed stone m.sand ) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) 25 dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in cement mortar 1:2 ( one cement and two crushed stone m.sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 26 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two crushed stone m.sand and four aggregate ) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. ( the rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers ) 27 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 ( one cement and threem.sand ) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers 28 plastering with cement mortar 1:4 ( one cement and three m.sand ) 20mm thick mixed with water proofing compound conforming to bis at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers. 29 plastering with cement mortar 1:5 ( one cement and five m.sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 30 providing cuddapa slab including all charges etc. 20mm / 30mm thick 31 supplying & fixing in positionof indian type baby water closet and erupean water closet including cost and conveyace of all materials to site etc. complete. 32 iwc 33 ewc 34 supplying and fabrication of steel door , window and ventilaters including all charges etc. 35 supplying and fabrication of steel doord ( 1.00x2.10m ) 36 supplying and fabrication of steel doord ( 1.10x2.10m ) ( 3 nos ) 37 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 38 supplying and fabrication of steel window w ( 1.2x1.3m ) ( 6 nos ) 39 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 40 providing rain water pipe including all labour charges etc. 41 towards labour charges forfixing of steel doors, 42 towards labour charges forfixing of steel windows, & ventilators 43 supplying & fixing of teracotta jally ( 0.90 x 0.45 ) 44 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 45 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 46 supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., ( without primer ) 47 black board painting two coats with including cost & conveyance of all materials to site and all labour charges etc., complete. 48 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 49 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 50 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 51 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting s.d.no: 88 52 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 40 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 53 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 54 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin plug point. sd 36 55 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 56 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wallsd 115 57 supply and fixing ofmain service board.etc complete. 58 towards for service connection for e.b.etc complete. 59 63mm pvc pipe 4ksc 60 63mm pvc mta 61 63mm pvc bend 62 1000litre hdpe tank 63 brass chromium plated screw down tap 15 / 12 mm dia ( heavy type ) 64 20 mm dia pvc items finolex ( or ) equivalent ( with isi monogram ) 10 kg / cm 2 65 20 mm dia pvccoupler 66 20 mm dia pvcelbow 67 earth work excavation in all clauses of soil as per ss20b. waterpipe line 68 labour charges for laying and joining pvc pipes including all cost etc complete 69 provision for cartoon paintings 70 provision for handrails 71 provision for name board 72 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38739118 tender for reddiyarchatram block agamt ii 2023 2024 package no 04. 1 part 1 : providing paver block at centre street from rajendran house to sahnmugam house h / o t.pudhupatti ( 100m ) .estimate amount rs.5.00 lakhs 2 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 3 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete.labour charges etc., complete. 4 supply and errection ofcentering for sides and soffits of cc works including cost and conveyance of all materials to site and all labour charges etc., complete. 5 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 6 construction of granulaer sub base by providing with graded materialof size9.5mm to 4.75mm metal in 66 % and 2.36mm in 34 % including all labour charges etc., complete.labour charges etc., complete. 7 providing and laying of inter locking concrete block pavements havingthickness 60mm and compacted over a thinincluding all labour charges etc., complete.labour charges etc., complete. 8 supply and fixing of citizen / information board including all cost and conveyance of all materials and all labour charges etc complete 9 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 10 part 2 : providing paver block at east street from palanisamy house to senthil house ( 45m ) .estimate amount rs.6.19 lakhs 11 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 12 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete.labour charges etc., complete. 13 supply and errection ofcentering for sides and soffits of cc works including cost and conveyance of all materials to site and all labour charges etc., complete. 14 cement concrete 1:3:6 mix using 20mm iss hbg metal including cost and conveyance of all materials to site and all labour charges etc., complete. 15 construction of granulaer sub base by providing with graded materialof size9.5mm to 4.75mm metal in 66 % and 2.36mm in 34 % including all labour charges etc., complete.labour charges etc., complete. 16 providing and laying of inter locking concrete block pavements havingthickness 60mm and compacted over a thinincluding all labour charges etc., complete.labour charges etc., complete. 17 supply and fixing of citizen / information board including all cost and conveyance of all materials and all labour charges etc complete 18 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 19 part 3 :deepening and strenthening of kappiliyappati pond with construction of baby pond and bathing ghat .estimate amount rs.10.00 lakhs 20 claening light jungle ( based on standard schedule of rate ) 21 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 22 main pond 23 baby pond 24 channel area 25 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 26 cement concrete 1:4:8 mix using 40mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15 cm thick compacting etc., complete complying with std. specifications and as directed. 27 refilling the excavated earth otherthen m. sand including all cost and conveyance of all matirials and all labour charges etc complete ., 28 supplying and erecting centering for sides and soffits including support and strutting up to 3.29m high for plane surface such as using mild steel sheets of size 90 x 40 cm and bg 10 stiffened with welded mild steel angle of size 25x25x3mm for boarding laid over silver oak ( country wood ) joists of size 10x6.50cm spaced at about 90 centre to centre and supported by casaurina props of 10 13cm dia spaced at 75cm c / c etc. complete. 29 supplying, fabricatingand placing of mild steel or ribbed for steel rods and all rcc works as per the design given including cost steel and binding wire in all floors etc., & convayence of steel as per std. specificationand directed. 30 cement concrete 1:3:6 mix using 40mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15 cm thick compacting etc., complete complying with std. specifications and as directed. 31 cement concrete 1:2:4 mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15 cm thick compacting etc., complete complying with std. specifications and as directed. 32 provision for name board charges 33 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 34 part 4 :construction of anaganwadi building at pudhupattiestimate amount rs.14.31 lakhs 35 earthwork excavation and depositing on bank with initial lead and lift in hard gravelly soil for foundation etc. complete. 36 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete 37 filling in foundation and basement with excavated earth in layers of not more than 15cm. thick well rammed, watered and consolidated complying with standard specifications etc., complete. 38 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 39 supplying and erecting shuttering including necessary support for plane surface in foundation basement and roof labs strutting upto 3.29m height for plane surfaces for floors for rcc column footings columns plinth beam and connected with foundations 40 supplying, fabricating and placing in position mild steel or ribbed to steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete. 41 rcc 1:1.5:3 mix using 20 mm iss hbg metal including cost & conveyance of all materials to site and all labour charges etc., complete. 42 cement concrete 1:2:4 mix using 20mm metal including cost and conveyance of all materials to site and labour charges etc. complete. 43 weathering course with best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no m.sand to be listed ) over the rcc roof slab in the proposition being brickjelly to lime 32:12:1 / 2 by volume and laid over into a single layer and cons 44 finishing the top of the roof with one course of machine pressedtiles of size 20 cm x 2 cm of approved quality laid in cement mortar 1:3 ( one cement and three m.sand ) 12 mm thick mixed with water proofing compound conforming to iss by 2% weight of cement us 45 paving the floor with vertified tiles of any colour and any size laid in cm 1:2 20mm thick and pointing with white cement 0.4kg / sqm mixed with colouring pigment to suit the colour of the tiles including finishing the joint neatly complying with std specification. 46 dadooing walls with glazed tiles of any colour and any size laid in cm 1:2, 10mm thick. and pointing with white cement 0.4 kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complete 47 providing the following thickness of granolithic pattern floor finish with plain cement concrete 1 : 2 : 4 mix using 10 12mm isshbg metal and the top rubed smooth etc., complete 25mm thickness 48 plastering with cm 1:3 mix 10mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 49 plastering with cm 1:4 mix 20mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 50 plastering with cm 1:5 mix 12mm thick including cost and conveyance of all materials to site and labour charges etc. complete. 51 providing cuddapa slab including all charges etc. 52 supplying & fixing in positionof indian type baby water closet including cost and conveyace of all materials to site etc. complete. 53 iwc 54 ewc 55 supplying and fabrication of steel doord ( 1.00x2.10m ) 56 supplying and fabrication of steel doord ( 1.10x2.10m ) 57 supplying and fabrication of steel door d1 ( 0.75x1.80m ) 58 supplying and fabrication of steel window w ( 1.2x1.3m ) 59 supplying and fabrication of steel ventilator ( 0.60x0.45m ) 60 towards labour charges forfixing of steel doors, 61 towards labour charges forfixing of steel windows, & ventilators 62 supplying and fixing of rcc jolly including all charges etc. 63 providing rain water pipe using 110mm pvc pipe including all labour charges etc. 64 colour washing two coatswith approved quality of oil bound distemper withgood colour pigments with primerincluding all charges etc. 65 painting two coats with best quality of ready mixed plastic emulison of ist class paintwith appd. colour approved by the departmental officersincluding cost & conveyance of all materials to site and all labour charges etc., complete. 66 painting two coats over new iron work using synthetic enamel paint without primer including cost and conveyace of all materials to site etc. complete. 67 painting two coats for black board including all charges etc. complete 68 supply and fixing of 16 ampsdpic switch of 500v grade with fuse and nutralon suitable t.w. board with painting of suitable colour with pwd earthing ( sd no.142 ) 69 supply and run of 2 of 6 sq. mm ( 84 / 0.30 ) polythene insulated and pvc unsheeted s.c. alu cable of 1100 v on 7 / 20 gi bearerwirefor service connection main sd.66 70 supply and run of 2 x1.5sq. mm ( 22 / .3 ) pvc insulated sc unsheeted cu. conductor of 1100grade in 25mm dia gi pipe ( glassb ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 69 71 supply and fixing of 11w cfl lamp for existing bh point. ( data b ) sd 80 72 supply and fixing of w.t. bulk head fitting complete with guard suitable for lamp with 60 w bulb with pvc unsheated leads from terminal to the fitting sd. 84 73 wiring with 2 x 1.5 sq.mm pvc uncheated sc cu.cable of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point & fan point sd 17 74 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin non inte plug point. sd 36 75 supply and fixing of ceiling fan ( crompton make ) including cost and conveyance of all materials and labour cherges etc complete.ceiling fan sd 114 76 supply and fixing of ac exhaust fan 300mm sweep complete without provision of hole in the wall exhaust fan 300mm sd 115 77 supply and fixing of main service board.etc complete. 78 provision rainwater harvesting 79 provison for cartoon painting 80 provision for handrails 81 providing pipe line arrangements 82 63mm pvc pipe 4ksc 83 63mm pvc mta 84 63mm pvc bend 85 1000litre hdpe tank 86 pvc tap 87 earth work excavation in all clauses of soil as per ss20b. 88 labour charges for laying and joining pvc pipes including all cost etc complete 89 provision for name board 90 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } 91 part 5:providing draiangenorth street vinayakar kovil to magudeeswaran kadai with horizontal soak pit ( 105m ) est amount :6.80lakhs 92 earthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 93 foundation 94 drainage 95 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 96 brick work in c.m 1:5 mix using country bricks including cost & conveyance of all materials to site and all labour charges etc., complete. 97 supply and errection of centering and shuttering charges etc., complete. 98 cement concrete 1:3:6 mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete 99 rcc 1:1:5:3mix using 20mm iss hbg metal for foundation including watering whenever necessary and laid in layers not more than 15cm thick compacting etc., complete 100 supply and fabrication of steel rod including curing cost and conveyace 101 plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials & all labour charges etc., complete. 102 90mm metal 103 40mm metal 104 20mm metal 105 provision for name board 106 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38598090 tender for agamt ii 2023 24 anangoor panchayat. 1 providing cement concrete pavement at mariammankovil street in anangoor colony in anangur panchyat 2 earthwork excavation forpavement &drain in all soilandsubsoilsand todepthasmaydirected except rockrequiring blasting but inclusiveof shoringandbalingoutwaterwherevernecessary etc., complete. ss20b. 3 cc 1:4:8 mix using 40mm iss hbg metal including all other labour charges etc 4 supplyinganderectioncenteringforsidesand sofficts inculdingcostandconveyancecostofall labourchargesetccomplete 5 cc 1:2:4mix using 20mm iss hbg metal including costofall other labour charges etc 6 cost and supply of 300mm dia rcc pipe 7 towards cost of nameboard charges 8 towards cost ofphotograph 9 towards cost of bitumen pad 10 construction of anganwadi building atanangur colony in anangur panchyat 11 earth work excavation and depositing on bank with intial lead and lift in all clasuses of soil such as hard gravely soil, gravely soil except hard rock requiring blasting etc complete as per ss20b for narrow foundation 12 cement concrete 1:4:8 mix using 40mm isshbg stone jelly for foundation and flooring including cost, conveveyance of all materials and labour chargesto laid in layers not more than 15cm thick, well rammed etc, complete with standard specification 13 refilling in basement with excavated earth in layers of not more than 15 cm thick , well watered, rammed and consolidated complying with standard specification etc complete . 14 supplying and filling inbasement withconveyed gravel in layers not more than 15 cm thick , well ramed and consolidated complying with standard specification 15 supplying and filling inbasement with filling sand in layers not more than 15 cm thick , well ramed and consolidated complying with standard specification 16 supplying and erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. rate for 10m2 for the following items ( rcc floor slab, roff slab, rectangular / square, tee / ell beams, lintels, staircase waist slablanding slab landing beam canopy etc in all floors with all cross bracings using mild steel sheets of size 90cm x 60cm and 10bg stiffened withmild steel angles of size 25mmx3mm for boarding laid over country wood joists of size 10cmx6.50cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre etc, complete and as directed. 17 superstructure 18 forsunshade & platform 19 toilet roof 20 supplying, fabricating and placin g in position of rts or ms rod for all reinforced cement concrete works as per design given including cost of steel and binding wire in all floors etc, complete complying with standard specification 21 reinforced cement concrete in 1 : 1.5 : 3 , mix using 20mm iss hbg stone jelly for all reinforced cement concrete works excluding cost of centering and stellbut including laying, vibrating, curing and finishing , fixing fan clamps in the rcc floor and roof slab works wherevver necessery and bearing surface of the wall at the sides and bottom of the slab, beam shall be finished smooth with cement mortor 1:3 and craft paper without claiming extra cost., complete compying with standard specification and as directed by the departmental officers 22 brick work in cement mortor 1 : 5 mix using country bricks of size 22 x 11 x 7 cm including cost and conveyance of all materials and labour charges etc complete . 23 plastering with cement mortor 1:5, 12mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specificationas directed by the departmental officers 24 plastering with cement mortor 1:3, 20mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specificationas directed by the departmental officers 25 special ceiling plastering and finishing all rcc exposed surfaces such as rcc slabs, canopies, sunshades, landing slab beams , etc with cementmortor 1:3, 10mm thick ( one cement and three sand ) including cost and conveyance of all materials and labour charges etc complete as directed by the departmental officers etc complete complying with standard specification. 26 weathering course concrete by using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be added ) over the rcc roof slab in the proportion of brick jelly to lime being 32 : 12.5 by volume and laid in a single layer and consolidated to the required slope and finished thickness by beating the concrete with wooden beaters if approved pattern keeping the surface constantly wet by sprinkling lime jaggery water as per standard specification etc., complete as directed by the departmental officers. 27 finishing the top of roof with one course of pressed tiles of size 23 cm x 23 cm x 2 cm laid incement mortor 1 : 3 mix usingm.sand and pointingwith the same mortor mixed with water proof compoundincluding cost conveyance of all materials and labour charges etc complete 28 paving the wall andfloor with best quality stain free nano polishvetrifiedtiles of size 60 cm x 60 cm x 8 mm any approved colour and sizeshape and quality laid in cement mortor 1 : 3 to 20 mm thick in all floors and the top pointed with the white cement 0.40 kg mixed with the same colouring pigments etc complete 29 paving the wall and floor with anti skid tiles of any colour and any size laid in cm 1 :2 , 20 mm thick andpointing with white cement 0.40 kgper sqm mixed with colouring pigment to match the colour of the tiles including finishing the joints neatly complying with the standard specification and as directed by the departmental officers . 30 dadooing walls with colour designed glazed tiles of sizes 300 mm x 200 mm x 6 mm size of approved make and quality and colour set in cement mortor 1 : 2 ( one cement and two sand ) over 10 mm base layer plastering and pointing with white cement neatly as directed . 31 fabrication and supply and delivery of mild steel doors of the following sizes with single leaf outer frame made of 35x35x5 mm equal m.s l angle and shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal and 3 nos diagonal using ms flat of size 20x5 mmfully covered with 18 guage plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos of holdfasts made of 35x35x5mm equal m.s.l angle, 1 no of wind appliance, 2 nos of tower bolts, 1 no of aldrop, 2 nos of handles, fixing the shutter with 6 nos of 6 inch hinges with outer frame of the door inculding painting the whole unit with one coat of best quality of red oxide primerof size 1.10 x 2.10 m 32 fabrication and supply and delivery of mild steel doors of the following sizes with single leaf outer frame made of 35x35x5 mm equal m.s l angle and shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal and 3 nos diagonal using ms flat of size 20x5 mmfully covered with 18 guage plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos of holdfasts made of 35x35x5mm equal m.s.l angle, 1 no of wind appliance, 2 nos of tower bolts, 1 no of aldrop, 2 nos of handles, fixing the shutter with 6 nos of 6 inch hinges with outer frame of the door inculding painting the whole unit with one coat of best quality of red oxide primer ofs size 1.00 m x 2.10 m 33 fabrication and supply and delivery of mild steel doors of the following sizes with single leaf outer frame made of 35x35x5 mm equal m.s l angle and shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal and 3 nos diagonal using ms flat of size 20x5 mmfully covered with 18 guage plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos of holdfasts made of 35x35x5mm equal m.s.l angle, 1 no of wind appliance, 2 nos of tower bolts, 1 no of aldrop, 2 nos of handles, fixing the shutter with 6 nos of 6 inch hinges with outer frame of the door inculding painting the whole unit with one coat of best quality of red oxide primer of size 0.75 m x 2.10 m 34 fabrication and supply and delivery of mild steel window of the following sizes with double leaf outer frame made of 35x35x5 mm equal m.s l angle mullion section made of 25x25x5mm equal t section , shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontalfor each each shutter using 25x25x5mm equal m.s t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly andalso fixing by welding protective grill with 12mm square m.s rods at an interval of not greater of not greater than 10cm centre to centre to the outer frame , 6nos of hold fasts made of35x35x5 mm equal m.s.l angle, 3nos of peg stays with holes for keeping the window open in different positions , 3nos of locking handles , fixing the shutter with 6 nos of 4inch hinges with outer frame of the windowinculding painting the whole unit with one coat of best quality of red oxide primer of size 1.20 x 1.30 m 35 fabrication and supply and delivery of mild steel window of the following sizes with double leaf outer frame made of 35x35x5 mm equal m.s l angle mullion section made of 25x25x5mm equal t section , shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontalfor each each shutter using 25x25x5mm equal m.s t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly andalso fixing by welding protective grill with 12mm square m.s rods at an interval of not greater of not greater than 10cm centre to centre to the outer frame , 6nos of hold fasts made of35x35x5 mm equal m.s.l angle, 3nos of peg stays with holes for keeping the window open in different positions , 3nos of locking handles , fixing the shutter with 6 nos of 4inch hinges with outer frame of the windowinculding painting the whole unit with one coat of best quality of red oxide primer of size 1.20 x 1.30 m 36 supply of rcc jolly of size 0.90 m x 0.45 m etc complete 37 supply and fixing of rcc jolly of size 0.60 m x 1.30 m including cost and labour charges etc complete 38 fixing charges for steel door in position etc complete 39 fixing charges for steel window in position etc complete 40 fixing charges for jolly in position etc complete 41 paving the floor with best quality anti skidtiles of any approved colour and size 300 mm x 300 mmx 8 mm shape and quality laid in cementmortor 1 : 2 to 20 mm thick in all floors and the top pointed with the white cement 0.40 kg mixed with the same colouring pigments etc complete 42 distembering two coats with best approved oil bound distember including cost of painting with primer coatover new plastered surface and conveyance of all materils to site and all labour charges etc complete 43 painting two coats with approved exterior emulsion over one coat of primer coat over plastered wall surface, ceiling and other new surface including cleaning , preparing the surface, curing, scaffolding charges etc, complete. 44 painting two coats over iron work including cost of paint and labour charges etc complete 45 providing and fixing pvc. rainwater downfall pipes of size 110 mm diametre with necessary shoes, bends and other specials, clamps, screws, nailsteakwood plugs etc complete including cost of all materials. the rate include cost of removable cast iron gratings of appropriate size.the size of teak wood plugs to be used is 150 mm x 25 mm in front and 200 mm x 75 mm in rear and all other sides with a depth of 100 mm . the pipe is to be fixed by means of u clamps at the centre of the pipe to be fixed in addition to these for more than three metres pipie length , complete complying with standard specification 46 suppling and fixing in position of baby freindlyindian water closet , white glazed earthen ware of approved quality with p trap or s trap confirming to is:2556 part xii with sand cushion and forming the closet using 40mm broken jelly lime concreteetc complete 47 supplying and fixing in position of coloured glazed europeyenwater closet of best quality and approved make with 100 mm p or s trap connecting with ci 100 mm dia / pvc pipe of 110 mm dia , double flapped rigid pvc back seat and seat cover with cp brass hinges including cost of white cement , cement for packing , spun yarn , teak wood plugs, brass screws , etc , including supplying and fixing 10 litres capacity pvc / 12.5 litres capacity porcelin low level flushing tank with a pair of ci brackets , etc., complete with all fittings such as 15 mm brass ball valve with polythene . 48 manufacturing, supplying and fixing of stainless steel hand rails for staircase steel hand rail for steps , ramp using 50 mm dia 304 l grade stainless steel pipe of 1.60 mm thick will be provided with tubular supports made of 304 l grade stainless pipe of 25 mm dia of 1.60 mm thick welded to the railing . the supports will be grouted into the wall and provided with 93.00 mm thick stainless steel circular base plate of 304 l grade .the rate shall included for groutting into concrete with necessasry supporting arrangements the hand rail in floor polishing buffing , bonding , cutting , grinding, conveyance, welding charges, electrical charges etc , complete 49 provision of pvc tank 500 litres 50 provision for lock and key 51 name of work : providing water supply arrangements 52 provision for rain water harvesting structures 53 provision for soak pit arrangements 54 provision for name board and photo charges 55 painting cartoons in hall and toilet and outer lettering, drawing pictures 56 construction of threshing floor @ near periya kulam at anangur panchyat 57 earthwork excavation forpavement &drain in all soilandsubsoilsand todepthasmaydirected except rockrequiring blasting but inclusiveof shoringandbalingoutwaterwherevernecessary etc., complete. ss20b. 58 cc 1:4:8 mix using 40mm iss hbg metal including all other labour charges etc 59 filling inthe basement with filling gravelincluding cost and conveyanceto the site and all labour charges for fillingas per standard specifications 60 filling inthe basement with filling sand including cost and conveyanceto the site and all labour charges for fillingas per standard specifications 61 supplayinganderectioncenteringforsidesand sofficts inculdingcostandconveyancecostofall labourchargesetccomplete 62 cc 1:3:6 mix using 20mm iss hbg metal including costofall other labour charges etc 63 cc 1:2:4mix using 20mm iss hbg metal including costofall other labour charges etc 64 supplying and fixing in position 40m dia best approved quality of b class g.i pipe of roof rafters and purlin to receive the gi sheet roof including cost of gi pipe 65 supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers. 66 towards cost of nameboard charges 67 towards cost of photo charges 68 towards cost of bitumen pad 69 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Rural Development And Panchayats Department - Tamil Nadu

38525688 tender for construction of panchayat office building colony at pallineliyanur panchayat. 1 construction of panchayat office building colony @ pallineliyanur panchayat 2 earth work excavation and depositing on bank with intial lead and lift in all clasuses of soil such as hard gravely soil, gravely soil except hard rock requiring blasting etc complete as per ss20b for narrow foundation 3 cement concrete 1:4:8 mix using 40mm isshbg stone jelly for foundation and flooring including cost, conveveyance of all materials and labour chargesto laid in layers not more than 15cm thick, well rammed etc, complete with standard specification 4 refilling in basement with excavated earth in layers of not more than 15 cm thick , well watered, rammed and consolidated complying with standard specification etc complete . 5 supplying and filling inbasement with filling sand in layers not more than 15 cm thick , well ramed and consolidated complying with standard specification 6 supplying and erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. rate for 10m2 for the following items ( rcc floor slab, roff slab, rectangular / square, tee / ell beams, lintels, staircase waist slablanding slab landing beam canopy etc in all floors with all cross bracings using mild steel sheets of size 90cm x 60cm and 10bg stiffened withmild steel angles of size 25mmx3mm for boarding laid over country wood joists of size 10cmx6.50cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre etc, complete and as directed. 7 for below gl centering 8 superstructure 9 for sill slab lintel, portico beam 10 supplying, fabricatung and placin g in position of rts or ms rod for all reinforced cement concrete works as per design given including cost of steel and binding wire in all floors etc, complete complying with standard specification 11 reinforced cement concrete in 1 : 1.5 : 3 , mix using 20mm iss hbg stone jelly for all reinforced cement concrete works excluding cost of centering and stellbut including laying, vibrating, curing and finishing , fixing fan clamps in the rcc floor and roof slab works wherevver necessery and bearing surface of the wall at the sides and bottom of the slab, beam shall be finished smooth with cement mortor 1:3 and craft paper without claiming extra cost., complete compying with standard specification and as directed by the departmental officers 12 grade beam 13 abovebasement 14 brick work in cement mortor 1 : 5 mix using country bricks of size 22 x 11 x 7 cm including cost and conveyance of all materials and labour charges etc complete . 15 upto basement 16 superstructure 17 plastering with cement mortor 1:5, 12mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specificationas directed by the departmental officers 18 plastering with cement mortor 1:3, 20mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specificationas directed by the departmental officers 19 special ceiling plastering and finishing all rcc exposed surfaces such as rcc slabs, canopies, sunshades, landing slab beams , etc with cementmortor 1:3, 10mm thick ( one cement and three sand ) including cost and conveyance of all materials and labour charges etc complete as directed by the departmental officers etc complete complying with standard specification. 20 weathering course concrete by using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be added ) over the rcc roof slab in the proportion of brick jelly to lime being 32 : 12.5 by volume and laid in a single layer and consolidated to the required slope and finished thickness by beating the concrete with wooden beaters if approved pattern keeping the surface constantly wet by sprinkling lime jaggery water as per standard specification etc., complete as directed by the departmental officers. 21 finishing the top of roof with one course of pressed tiles of size 23 cm x 23 cm x 2 cm of approved quality laid in cement mortor 1 : 3 ( one cement and three sand ) 12 mm thick mixed with water proofing compound confirming to is at 2% by weight of cement used and the top pointed with same mortor mixed with redoxide to the full depth of tiles , complete coplying with standard specification ( the rate inclusive of redoxide and water proofing compound ) and as directed by the departmental officers . 22 paving the floor with best quality ceramic tiles of size 600 mm x 600 mmof approved colour, shade and quality laid in cement mortor 1 : 3 ( one cement and three sand ) 20 mm thick in all floors and the top pointed with the white cement mixed with same colouring pigments and as directed by the departmental officers etc complete complying with standard specification 23 paving the floor with best quality anti skidtiles of any approved colour and size 300 mm x 300 mmx 8 mm shape and quality laid in cementmortor 1 : 2 to 20 mm thick in all floors and the top pointed with the white cement 0.40 kg mixed with the sa 24 dadooing walls with colour designed glazed tiles of sizes 300 mm x 200 mm x 6 mm size of approved make and quality and colour set in cement mortor 1 : 2 ( one cement and two sand ) over 10 mm base layer plastering and pointing with white cement neatly as directed . 25 supply of mild steel door of size 1.10 m x 2.10 m with two leaf. outer frame o f40 x 40x 6 mm equal ms angle, shutter frame made of 35 x325 x 5 mm equal ms angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using ms plate of size 20 x 5 mm fully covered with 18 gauge plain ms full sheet welded with shutter frame neatly and also fixin by welding, tower bolts 30 cm long , butt hingestwo nos of locking handles fixing the shutterincluding painting the whole unit with one coat of best quality red oxide primer . 26 supply of rolling shutter of size 1.20 m x 2.10 mwith frame and locking arrangements etc complete 27 solid pvc door shutter using 19 gauge 19 mm ms sq . tubes for styles and outer frames , 15 mm ms sq .tubes for top , lock and bottom rails . the steel tubes shall be covered with 5 mm thick solid pvc sheets , shutter using 5 mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings . the over all size of styles shall be 50 mm x 30 mm. the over all size of top rail , lock rail and bottom rail shall be 75 mm x 30 mm . the over al lsize of frames shall be50 mm x 45 mm with suitable rebate for housing the shutter . 28 supply of mild steel window of size 1.20 m x 1.30 m with two leaf. outer frame of 35 x 35 x 5 mm equal ms angle , mullion section made of 35 x 35 x 5 mm equal tee section , shutter frame made of 25 x 25 x 5 mm equal ms angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using ms plate of size 20 x 5 mm fully covered with 18 gauge plain ms full sheet welded with shutter frame neatly and also fixin by welding , protective grill with 12 mm square m s rods at an interval of not greater than 10 cm centre to centre to the outer frame , two nos peg stays with hole for keeping the windows open in different positions , two nos of locking handles fixing the shutter with four nos of hinges hold fasts , six nos of hinges with outter frame of the window including painting the whole unit with one coat of best quality red oxide primer . 29 supply and fabrication of steel grill gate of over all size of 1.50 m x 2.10 m using structural steel etc complete in all respects as directed 30 supply and fixing of rcc jolly of size 0.60 m x 0.45 m including cost and labour charges etc complete 31 supply and fixing of cudappa slab 20 mm thick including cost and conveyance to site and labour charges etc complte 32 distembering two coats with best approved oil bound distember including cost of painting with primer coatover new plastered surface and conveyance of all materils to site and all labour charges etc complete 33 painting two coats with approved exterior emulsion over one coat of primer coat over plastered wall surface , ceiling and other new surface including cleaning , preparing the surface, curing, scaffolding charges etc, complete. 34 painting two coats over iron work including cost of paint and labour charges etc complete 35 providing and fixing pvc. rainwater downfall pipes of size 110 mm diametre with necessary shoes, bends and other specials, clamps, screws, nailsteakwood plugs etc complete including cost of all materials. the rate include cost of removable cast iron gratings of appropriate size.the size of teak wood plugs to be used is 150 mm x 25 mm in front and 200 mm x 75 mm in rear and all other sides with a depth of 100 mm . the pipe is to be fixed by means of u clamps at the centre of the pipe to be fixed in addition to these for more than three metres pipie length , complete complying with standard specification 36 suppling and fixing in position of indian water closet coloured of size 580 mm x 440 mm , white glazed earthen ware of approved quality with p trap or s trap confirming to is:2556 part xii with sand cushion and forming the closet using 40mm broken jelly lime concreteetc complete 37 suppling and fixing in position ofeuropean water closet coloured with p or s trap with double flapped seat and seat cover with brass hinges and 10 litre capacity pvc low level flushing tankwith all internal fittingsof size 580 mm x 440 mm , white glazed earthen ware of approved quality with p trap or s trap confirming to is:2556 part xii with sand cushion and forming the closet using 40mm broken jelly lime concreteetc complete 38 supply and fixing of coloured wash hand basin with pedestal of size 550 mm x 400 mm with all accessories such as cast iron brackets , 32 mm dia cp waste coupling , rubber plug and chain , 32 mm dia b class g i waste pipe, 15 mm dia gm wheel valve , 15 mm dia nylon connection , 15 mm dia brass nipples , 15 mm cp . pillar tap etc complete . 39 hand rails stainless steel by manufacturing , suppying and fixing of stailess steel hand rails for staircase near wet riser using 50 mm dia 304 l grade stainless steel pipe of 1.60 mm thick will be provided with tubular supports made of 304 l grade stainless steel pipe of 25 mm dia of 1.60 mm thick welded to the railing. the supports will be grouted into the wall and provided with 93 mm thick stainless steel circular base plate of 304 grade . the rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing , bonding , cutting , grinding , conveyance welding charges , electrical charges etc complete . 40 wiring with 2 x 1.50 sqm ( 22 / 0.3 ) pvc insulated sc unsheathedcu conductor of 1100 v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accesseries, in flush with wall , with tw box 150 mm x 100 mm x 113 mm tw switch box with 3 mm thick hylem sheet coverfor 5a3 pin non inter locking cs plug with painting of suitable colour with contionues earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed plug point sd no 38 for pvc plug point 41 wiring with 2 x 1.50 sqm ( 22 / 0.3 ) pvc insulated unsheathed single core copper conductor of 1100 v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accesseries with tw switch box with 5 a f . t . switchand making good of the concealed portionwithsuitable colour forpvcconcealed light point and fan point s d n o 16 42 supply and fixing of fancy glass shade and11 wcfl in the existing light point sdno 80 43 supply and fixing of single box type 440 w fiu fitting complete with copper choke and condenser with teak wood round blocks on wall or ceiling with fiu tube with pvc unsheathed copper leads from terminals to the fitting sd no 88 44 supply and fixing of 32 a dpic switch of 500 v with f & n ( side handle ) on suitable t w box with pwd earthing ( s d n o 141 ) 45 supply and run of 2 of 6 sqmm ( 84 / 0.3 ) pvc insulated single core unsheathed copper conductor of 1100 v grade on 7 / 20 g i bearer wire for service connection mains ( s dno 66 ) 46 supply and run of 2 of 6 sqmm ( 84 / 0.3 ) pvc insulated single core unsheathed copper conductor of 1100 v grade in25 mm dia g i suitable pipe bclass suitably bended both ends with necessery angle iron upright and end support for mains ( s d n 71 ) 47 supply and fuixing of water tight bulk head fitting with guard suitable for 11 wlamp withcfl sd no 83 48 supply and fixing of 1200 mm ( 48 ) a c ceiling fan complete with stepped eloctronic 300 w regulator with 1.00 meter down rod on the existing clamp s d n o 106 49 supply and fixing of tneb meter board suitable for 32 a single phase sc . with 32 a fuse unit etc complete . sd no 125 50 provision for eb deposit charges 51 provision for1000 litres hdf pvc tank 52 provision for pipe line and tap forwater supply arrangements 53 provision for rain water harvesting structures 54 provision for soak pit arrangements 55 provision for name board 56 provion for photo charges 57 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Integral Coach Factory - Tamil Nadu

38259844 auction sale of description: scrap magnetic stainless steel shop refuse of various grades consisting of regular / irregular offcuts of sheets, plates, channels, pipes of all sorts, sizes and designs, punchings, remnants of punchings, window punchings of all sorts and sizes, small bits and strips of s.s magnetic variety, all rejected / obsolete fabricated magnetic stainless steel coach components generated from lhb unit, condemned / obsolete stainless steel seat, luggage and berth frames, rejected and obsolete stainless steel coach components, stainless steel window punchings, handles of all sorts, shapes, obsolete stainless steel fasteners, couplings , unusable to icf.note: ( 1 ) any ms , non ferrous / plastic attachments can be removed at the time of delivery, ( 2 ) jcb permitted for spreading gst 18 percent.other taxes as applicable.gst and any other taxes as imposed by central or state government will be to buyer?s account?location: north peripheral road at area opposite to street light pillar no 8 and street light pillar no 9. ( north side of scrap yard ) quantity 20000 kg.ul no 36 9809 0719 13 14.hsn code 720421....

Rural Development And Panchayats Department - Tamil Nadu

38035250 tender for construction of anganwadi building at village area in sathipattu panchayat. 1.01 construction of anganwadi building at village area in sathipattu panchayat 1.02 earth work excavation and depositing on bank with intial lead and lift in all clasuses of soil such as hard gravely soil, gravely soil except hard rock requiring blasting etc complete as per ss20b for narrow foundation 1.03 cement concrete 1:4:8 mix using 40mm iss hbg stone jelly for foundation and flooring including cost, conveveyance of all materials and labour charges to laid in layers not more than 15cm thick, well rammed etc, complete with standard specification 1.04 refilling in basement with excavated earth in layers of not more than 15 cm thick , well watered, rammed and consolidated complying with standard specification etc complete . 1.05 supplying and filling in basement with conveyed gravel in layers not more than 15 cm thick , well ramed and consolidated complying with standard specification 1.06 supplying and filling in basement with filling sand in layers not more than 15 cm thick , well ramed and consolidated complying with standard specification 1.07 supplying and erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. rate for 10m2 for the following items ( rcc floor slab, roff slab, rectangular / square, tee / ell beams, lintels, staircase waist slablanding slab landing beam canopy etc in all floors with all cross bracings using mild steel sheets of size 90cm x 60cm and 10bg stiffened withmild steel angles of size 25mmx3mm for boarding laid over country wood joists of size 10cmx6.50cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre etc, complete and as directed. 1.08 superstructure 1.09 for sunshade & platform 1.1 for lintel, beam and slab 1.11 supplying, fabricating and placin g in position of rts or ms rod for all reinforced cement concrete works as per design given including cost of steel and binding wire in all floors etc, complete complying with standard specification 1.12 reinforced cement concrete in 1 : 1.5 : 3 , mix using 20mm iss hbg stone jelly for all reinforced cement concrete works excluding cost of centering and stell but including laying, vibrating, curing and finishing , fixing fan clamps in the rcc floor and roof slab works wherevver necessery and bearing surface of the wall at the sides and bottom of the slab, beam shall be finished smooth with cement mortor 1:3 and craft paper without claiming extra cost., complete compying with standard specification and as directed by the departmental officers 1.13 brick work in cement mortor 1 : 5 mix using country bricks of size 22 x 11 x 7 cm including cost and conveyance of all materials and labour charges etc complete . 1.14 plastering with cement mortor 1:5, 12mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specification as directed by the departmental officers 1.15 plastering with cement mortor 1:3, 20mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specification as directed by the departmental officers 1.16 special ceiling plastering and finishing all rcc exposed surfaces such as rcc slabs, canopies, sunshades, landing slab beams , etc with cementmortor 1:3, 10mm thick ( one cement and three sand ) including cost and conveyance of all materials and labour charges etc complete as directed by the departmental officers etc complete complying with standard specification. 1.17 paving the wall and floor with best quality stain free nano polish vetrified tiles of size 60 cm x 60 cm x 8 mm any approved colour and size shape and quality laid in cement mortor 1 : 3 to 20 mm thick in all floors and the top pointed with the white cement 0.40 kg mixed with the same colouring pigments etc complete 1.18 paving the wall and floor with anti skid tiles of any colour and any size laid in cm 1 :2 , 20 mm thick and pointing with white cement 0.40 kg per sqm mixed with colouring pigment to match the colour of the tiles including finishing the joints neatly complying with the standard specification and as directed by the departmental officers . 1.19 dadooing walls with colour designed glazed tiles of sizes 300 mm x 200 mm x 6 mm size of approved make and quality and colour set in cement mortor 1 : 2 ( one cement and two sand ) over 10 mm base layer plastering and pointing with white cement neatly as directed . 1.2 fabrication and supply and delivery of mild steel doors of the following sizes with single leaf outer frame made of 35x35x5 mm equal m.s l angle and shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal and 3 nos diagonal using ms flat of size 20x5 mmfully covered with 18 guage plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos of holdfasts made of 35x35x5mm equal m.s.l angle, 1 no of wind appliance, 2 nos of tower bolts, 1 no of aldrop, 2 nos of handles, fixing the shutter with 6 nos of 6 inch hinges with outer frame of the door inculding painting the whole unit with one coat of best quality of red oxide primer of size 1.10 x 2.10 m 1.21 fabrication and supply and delivery of mild steel doors of the following sizes with single leaf outer frame made of 35x35x5 mm equal m.s l angle and shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal and 3 nos diagonal using ms flat of size 20x5 mmfully covered with 18 guage plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos of holdfasts made of 35x35x5mm equal m.s.l angle, 1 no of wind appliance, 2 nos of tower bolts, 1 no of aldrop, 2 nos of handles, fixing the shutter with 6 nos of 6 inch hinges with outer frame of the door inculding painting the whole unit with one coat of best quality of red oxide primer ofs size 1.00 m x 2.10 m 1.22 fabrication and supply and delivery of mild steel doors of the following sizes with single leaf outer frame made of 35x35x5 mm equal m.s l angle and shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal and 3 nos diagonal using ms flat of size 20x5 mmfully covered with 18 guage plain m.s full sheet welded with shutter frame neatly and also fixing by welding 6 nos of holdfasts made of 35x35x5mm equal m.s.l angle, 1 no of wind appliance, 2 nos of tower bolts, 1 no of aldrop, 2 nos of handles, fixing the shutter with 6 nos of 6 inch hinges with outer frame of the door inculding painting the whole unit with one coat of best quality of red oxide primer of size 0.75 m x 2.10 m 1.23 fabrication and supply and delivery of mild steel window of the following sizes with double leaf outer frame made of 35x35x5 mm equal m.s l angle mullion section made of 25x25x5mm equal t section , shutter frame made of 25x25x5mm equal m.s.l angle for horizontal and vertical members and the shutter frame strengthenened by stiffeners of 2 nos horizontal for each each shutter using 25x25x5mm equal m.s t section fully covered with 18 gauge plain m.s full sheet welded with shutter frame neatly andalso fixing by welding protective grill with 12mm square m.s rods at an interval of not greater of not greater than 10cm centre to centre to the outer frame , 6 nos of hold fasts made of 35x35x5 mm equal m.s.l angle, 3 nos of peg stays with holes for keeping the window open in different positions , 3 nos of locking handles , fixing the shutter with 6 nos of 4inch hinges with outer frame of the window inculding painting the whole unit with one coat of best quality of red oxide primer of size 1.20 x 1.30 m 1.24 fabrication and supply of n type mild steel glazed ventilators ( in two parts ) of the following size with outer frame made of 25x25x5 mm equal m.s.l angle with intermediate rails using 25x25x5 mm m.s t section for panels with 3mm thick pin headed glass with teak wood beading and glass putty and also fixing by welding protective grill with 12mm square m.s rods at an interval of not greater than 10cm centre to centre to the outer frame , 4 nos of hold fasts connecting the 2 parts at 75 mm clear and with 45 degree inclination with 25x25x5mm 10g weld mesh and wire mesh including painting the whole unit with one coat of best quality of redoxide primer of .size 0.90 x 0.45 m 1.25 supply of rcc jolly of size 0.90 m x 0.45 m etc complete 1.26 supply and fixing of rcc jolly of size 0.60 m x 1.30 m including cost and labour charges etc complete 1.27 fixing charges for steel door in position etc complete 1.28 fixing charges for steel window in position etc complete 1.29 fixing charges for jolly in position etc complete 1.3 providing gronolothick floor finish in plain cement concrete 1 : 2 : 4 ( one cement, two sand and four aggregate ) using 10 to 12 mm gauge hard broken stone jelly including laying , finishing and the top rubbed smooth with trawel thread lining , curing etc , complete complying with standard specification and as directed by the deparmental officers . 1.31 distembering two coats with best approved oil bound distember including cost of painting with primer coat over new plastered surface and conveyance of all materils to site and all labour charges etc complete 1.32 painting two coats with approved exterior emulsion over one coat of primer coat over plastered wall surface, ceiling and other new surface including cleaning , preparing the surface, curing, scaffolding charges etc, complete. 1.33 painting two coats over iron work including cost of paint and labour charges etc complete 1.34 providing and fixing pvc. rainwater downfall pipes of size 110 mm diametre with necessary shoes, bends and other specials, clamps, screws, nailsteakwood plugs etc complete including cost of all materials. the rate include cost of removable cast iron gratings of appropriate size.the size of teak wood plugs to be used is 150 mm x 25 mm in front and 200 mm x 75 mm in rear and all other sides with a depth of 100 mm . the pipe is to be fixed by means of u clamps at the centre of the pipe to be fixed in addition to these for more than three metres pipie length , complete complying with standard specification 1.35 suppling and fixing in position of baby freindly indian water closet , white glazed earthen ware of approved quality with p trap or s trap confirming to is:2556 part xii with sand cushion and forming the closet using 40mm broken jelly lime concrete etc complete 1.36 supplying and fixing in position of coloured glazed europeyen water closet of best quality and approved make with 100 mm p or s trap connecting with ci 100 mm dia / pvc pipe of 110 mm dia , double flapped rigid pvc back seat and seat cover with cp brass hinges including cost of white cement , cement for packing , spun yarn , teak wood plugs, brass screws , etc , including supplying and fixing 10 litres capacity pvc / 12.5 litres capacity porcelin low level flushing tank with a pair of ci brackets , etc., complete with all fittings such as 15 mm brass ball valve with polythene . 1.37 manufacturing, supplying and fixing of stainless steel hand rails for staircase steel hand rail for steps , ramp using 50 mm dia 304 l grade stainless steel pipe of 1.60 mm thick will be provided with tubular supports made of 304 l grade stainless pipe of 25 mm dia of 1.60 mm thick welded to the railing . the supports will be grouted into the wall and provided with 93.00 mm thick stainless steel circular base plate of 304 l grade .the rate shall included for groutting into concrete with necessasry supporting arrangements the hand rail in floor polishing buffing , bonding , cutting , grinding, conveyance, welding charges, electrical charges etc , complete 1.38 provision of pvc tank 500 litres 1.39 provision for lock and key 1.4 provision for rain water harvesting structures 1.41 provision for soak pit arrangements 1.42 provision for name board and photo charges 1.43 painting cartoons in hall and toilet and outer lettering, drawing pictures 1.44 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...